At what speed to drill an electric screwdriver

The need to hang a chandelier, install hinged cabinets, a socket is not t.D., The moment comes in the current life of every owner of the living space. Given the fact that concrete columns, ceilings are not ceilings. This is a very common thing for modern apartments, it may come out so that the fasteners have to be mounted on a concrete structure. If you are “lucky”, then it will quite be what will ask the question of how to drill concrete?

Concrete is one of the most durable building materials at the moment. For what materials are the peorator used. Is it possible to drill wood, metal or tile. However, its strength is the main problem here, since it is prohibited to drill reinforced concrete without specialized equipment. With all this, the call of specialists to form several small.Sized holes will cost you a disproportionately large amount.

Drilling the wall with a pedorator drill: photo

If you want to save money, it will be useful to think about an independent solution to this problem. Despite the obvious difficulty. The correct approach is not a clear observance of the technological part of the process helps to achieve a qualitative result. Below you will be given a detailed instruction what is really, how to drill concrete in artisanal conditions.

Tools

To drill a reinforced concrete surface, it is necessary to use specialized tools. In our version, you cannot do with a home.Made tool.

Change of nozzles

During home repairs or other operations, the master often has to perform a change of nozzle. So that this procedure does not delay the process, you need to know how to secure a bat, drill or screwdriver correctly in an electric screwdriver.

The equipment is fixed in a special element called a cartridge. The selected nozzle is pinched manually using a special key or automatically (without using the latter). The fastener method is determined by the type of cartridge.

Planetary Gear Set

Varieties of cartridges

Most models use a quick.Packed version of the equipment holder. To carry out the procedure with one hand, insert the nozzle between the open fists, and the other is slowly pressed on the trigger. In this case, the sleeve will rotate clockwise. In models with a key cartridge, the new equipment is inserted into the nest and rotated in the same direction until it stops.

To extract a drill or bit, the tool is switched to a reverse, fix the cartridge and press the Start button. At the same time, fists are unclenched, and the nozzle is easily extracted.

Make sure that the drill or bit is tightly clamped in the cartridge, you can turn on the tool in idle. With proper installation, the nozzle will not hesitate and deviate.

Tool use options

Answering the question of how to use an electric screwdriver for beginners, you need to take into account the tasks of using the tool.

Drilling metal and wood using an electric screwdriver

To make a hole in strong materials, you must choose the right drill and set the desired mode. This is done using the rotary part of the tool, which is located directly behind the cartridge. Then the drill must be put to the desired point and press the start button.

Note! It is important to keep the device strictly perpendicular. Otherwise, the drill may break.

Drilling concrete and stone using an electric screwdriver

To answer the question of how to properly drill concrete with an electric screwdriver, you must first pay attention to the choice of a drill. It should have a winning tip. Usually used drills with a diameter of 6 mm. Too thick devices are not suitable, since the power of the electric screwdriver will be too small.

Keep the tool required perpendicular to the axis. It is not required to crush too much on the drill. From time to time, the pressure is required to weaken.

Twisting screws, screws and bolts with an electric screwdriver

This is the main purpose of an electric screwdriver. Each tool has a number of numbers that indicate a protracting moment. The thicker the fasteners and firmly the material, the more value you need to install.

To tighten screws into roofing metal, the value of 12-14 is required. To tighten ordinary screws into a tree, 8 is enough.

You also need to know how to insert a screwdriver into an electric screwdriver. During the tightening of the mount, you need to press the bit quite strongly so that it slip.

Functionality and equipment

Which electric screwdriver is better to choose for work, based on its capabilities, a question that interests many users.

Network and battery models

Squads working from the network can be purchased when repairing small rooms. The main plus of such tools is a constant source of electric current. But the work may be limited by the length of the wire.

Batteries are more autonomous. A large amount of work at a construction site, assembly of metal structures. All this will require the presence of a powerful tool. The advantages of such devices are a long service life and functionality. The disadvantages include a high price tag of some copies.

Bruste or best

The brush (collector) version of the engine of an electric screwdriver is considered inexpensive and popular. The design has brushes to remove excess current. Only one advantage is low price. Of the shortcomings. Low efficiency and the inability to work in fire hazardous places.

The brilliant engine has more advantages:

  • Long time for use.
  • When loading on the cartridge, the revolutions are not reduced.
  • You can work in explosive places.
  • The rotation frequency mode is wider than the brush engines.

Of the minuses there is a high price. But in professional activities you can not do without such tools.

The diameter of the cartridge and the size of the square

Much depends on what problem the electric screwdriver will solve. If at the entire stage of the work a high power of the tool is required, respectively, the diameter of the cartridge should be larger.

There are no exact parameters for such purposes, but there are general diameters for all cartridges. They vary from 8 to 13 mm., Depending on the tool model.

Square for all screwdrivers is common. ½ inch.

Type of battery, capacity, type of fastening

In batteries, 3 batteries are used in battery screws:

Household models have a battery capacity of no more than 2 ah. A professional tool has an indicator from 2 to 6 Ah. The question arises, at what temperature you can operate with an electric screwdriver with different capacities? High capacity allows you to operate the tool in adverse conditions, for example, in the frost.

From mounts, the most common are 3 types:

  • Threaded mount. The thread is located inside the cartridge, on the shaft;
  • The carvings of the type of “cone Morse”. The simplest type of fastening;
  • Fixed screw. Helps to keep the part in the right position.

Weight

The smaller the mass of an electric screwdriver, the easier it is to use it. If the work is associated with a simple repair of a house or on the street, you can purchase a tool with a mass of 0.8-0.9 kg. When drilling holes, working with brick or concrete, it is better to look for a more massive tool on sale. From 0.9 to 1.5 kg.

Before inserting the seeder, first make sure that the seeder is in working condition and disconnect it from the power source. Only then can you start training.

Installation of a working tool on a peorater

As indicated above, the hammer should be checked before installing the drill. To perform such a test, a regimen for not combat drilling is established. If you hear and feel that the engine works smoothly and without shock when pressing the start button on the device, this means that the hammer can be used as intended after drilling or drilling.

To attach a drill with a cylindrical shank in a peorator, use a cam adapter

Before inserting the drill into the peoporator, the shank of the working tool should be treated with a special lubricant that will protect it from corrosion. The procedure for installing drills in the drill is as follows.

  • The peorator is installed on the back of the floor or other hard surface.
  • The mobile part of the clamping device is allotted back.
  • The tool is inserted into the punch until it stops. In this case, a drill or drill for inserting in a drill should be kept vertically. If you do not comply with this requirement, you may encounter a breakdown or even a breakdown of the tool, which can also lead to a malfunction of the drilling bite.

Click to the click, then pull out the drill if it does not work. Everything is fine

Due to the fact that clamping cartridges on modern peorators are distinguished by a rather simple principle of operation, questions about how to get a drill from a peorator, as a rule, does not arise.

After removing the used tool from the penetrator to replace it with others, it is recommended to immediately clean the shank of fat and construction dust. The drill chin you are going to insert should also be cleaned and pre.Lubricated. The tool replaced in this way will not damage the shock mechanism and will last much longer.

The lubricant extends the service life of both the drill and the drill

With the help of a pedorator, you can not only get a drilled structural element, but also process using a special bite. You can also install the mixer of the device as a working body.

Homemade employees also often have questions about how to insert a drill into a screwdriver or how to replace the cartridge with a shock drill. The first issue is easy to resolve, since cartridges of the same design are used in the design of the screwdrivers as for drills and peorators. But to the question of how to properly replace the cartridge with the pea, you need to approach with the ability: to carry out such a procedure without certain knowledge and skills is not easy.

Some tips for using a drilling tool

In order to avoid the risk of harm to your health with flying tools or concrete chips, drilling should be performed with all precautions. To ensure this safety, you should use protective glasses, gloves, bears or ears plugs. Naturally, all work should be performed in special clothing in which there should not be hanging elements that can be wound on the drill

Naturally, all work should be performed in special clothing in which there should not be hanging elements that can be wound on the drill.

To prevent overheating of the power tool used for drilling, it should be related regularly

speed, work, electric, screwdriver, number

It is very important to insert the drill correctly (this must be done until the tool stops)

Two ways to squeeze a thin cartridge if the fists reach the shank slightly

If the drill stuck in the wall during drilling, it should be removed without removing the tool from its surface. To do this, remove the drill out of the penetrator and insert another with which you want to start breaking the wall around the drilled hole in it.

If the drill cannot be extracted from a drill or a pedorator, it should be squeezed in a vice, and then pressed with a hammer with a wooden gasket to press the cams of the clamping mechanism. Oil can help with this, a few drops of which are poured into a key cartridge.

Magnetization and hardening of nozzles

A large number of nozzles are produced in China from soft material. Therefore, they quickly lose their shape. The new bit is enough for a short time. To extend the life, the nozzle must be tempered. You will need: machine oil, gas burner or gas stove, a small container for oil from any tin can, a piece of steel wire.

    Wrap the wire on the bit so that it does not fall out.

speed, work, electric, screwdriver, number

The hardened bat will last longer than the usual.

For ease of work, especially in hard.To.Reach places, nozzles are magnetized. This can be done in several ways.

Method 1

You will need to purchase a special device for magnetization and demagnetization of the screwdrivers. Insert the bit there. The square window is magnetized, and the stepped. On the contrary.

Device for magnetization and demagnetization

Device for magnetization and demagnetization

Method 4

  • Buy in the radio store neodymium magnets.
  • Divide them into two parts and put them in one row so that the formed groups push off from each other. Put a plastic cap from the handle between them. To keep the repulsive magnets, fix them with plasticine.

The process of magnetization of bats by neodymium magnets

As a result, the nozzle will magnetize the fasteners better than the new.

Is it possible to drill metal with an electric screwdriver

If there is no drilling machine or drill in stock, metal products can also be drilled with an electric screwdriver. The main thing is to choose the right equipment. Equipment for concrete, wood or tiles made of ceramics, formed and imprisoned in different ways. For metal, equipment is indicated by the letters HSS.

To increase strength and resistance to wear, the working surface of the equipment is covered with titan. For steels of a solid structure, equipment with marking R18 is used. If COBALT is added to the coating, then the strength of the equipment increases significantly. Now you can not think how to drill the front door of the front door with an electric screwdriver.

You can drill even alloyed steel with electric screwdriver if the tip of the drill. But this is already from the field of experiments, as it will come out for a lot. If the metal is thin.Leafy, conical drill is used when drilling.

Equipping an electric screwdriver for metal has the designation HSS

Is it possible to drill metal with an electric screwdriver

If there is no drilling machine or drill in stock, metal products can also be drilled with an electric screwdriver. The main thing is to choose the right equipment. Equipment for concrete, wood or tiles made of ceramics, formed and imprisoned in different ways. For metal, equipment is indicated by the letters HSS.

To increase strength and resistance to wear, the working surface of the equipment is covered with titan. For steels of a solid structure, equipment with marking R18 is used. If COBALT is added to the coating, then the strength of the equipment increases significantly. Now you can not think how to drill the front door of the front door with an electric screwdriver.

You can drill even alloyed steel with electric screwdriver if the tip of the drill. But this is already from the field of experiments, as it will come out for a lot. If the metal is thin.Leafy, conical drill is used when drilling.

Equipping an electric screwdriver for metal has the designation HSS

Master Class. How to make a lathe from a drill

You will be surprised, but the drill can also be used to create a simple lathe. All structural elements are made with their own hands (with the exception of screws and bearing). There is nothing superfluous. Only the most necessary!

First of all, you need to prepare everything that is required to work.

What is required for a lathe

Next, you should decide what the size of the countertop will be. It is not necessary to take the dimensions given in the example. You can have their own.

The dimensions of the countertop

After that, the center at the drill is determined. It is placed on the countertop, then the distance from it (countertops) to the center of the cartridge is measured. A square wood is taken, a hole for the neck of the drill is made in it. The center of this hole will be a previously measured distance. Thanks to this, the drill will be recorded exactly.

All unnecessary is cut, after which the mount should be set aside for a while.

The excess is cut off

We proceed to the assembly of two corner parts, which are a couple of rectangular woods glued with each other.

Assembly of corner parts

A smaller part (grandmother) will hold a spinning workpiece from the opposite side, and a large one is a bed, the tool itself will rely on it

It is important that the height of the grandmother is about 1.5 times larger

Then, guides are created on both blanks. Holes are drilled along the line, which are then connected at an angle.

Xiaomi Wowstick 1F: The Life-Changing Mini Electric Screwdriver

The holes are connected at the slope and the bed

3 important elements are ready. If you want, paint them with a can.

A hole for the bearing is drilled in the grandmother (it should not be through). A bolt is inserted into the bearing itself, tightened with a nut. Glue is applied to the seat, then the bearing is placed (it should be a nut outside).

First, a small hole in the water location of the adhesive is inserted by a nut to the end

Directors from the racks are attached to the countertop. Holes (3 pieces) are drilled for long bolts, fastening for a drill is fixed with self.Tapping screws. You need to install a small wooden rectangle under the handle of the drill. All parts are screwed.

Directs from the re.Strengthening under the driller gear under the handle of the drill

The drill itself is fixed with self.Tapping screws. It should “sit” hard.

The design is almost ready, it remains only to make a fixator to hold the workpiece. For this purpose, circle is cut out, self.Tapping screws are inserted into it, as well as a bolt with a nut.

A round.Haired self.Tapping clamp is screwed in the circle

The finished part is attached in the cartridge.

Fixer fastening in the patronage of the lathe

| Denial of responsibility | Contacts |RSS