How much fishing line is needed per trimmer for grass

If the fishing line for the trimmer does not correspond to the power of the power unit, then this is fraught with the development of the following consequences:

  • If you use a thin cord on a powerful gasoline trimmer, the material will wear out quickly, the productivity and efficiency of the tool will decrease
  • If you put a fishing line for a low-power electric trimmer for a trimmer with a cross section of 2.6-3 mm-performance will decrease, constant wound of the cord on the coil will be observed, and the load on the motor will also increase, which will cause its accelerated wear

For the manufacture of fishing line, such material as nylon is used. It provides high reliability indicators, and also has good cutting properties. Why use a fishing line for a trimmer on a trimmer if there are metal disks? This question is asked by many masters.

  • A cord or fishing line for a trimmer on a tool is used when a vegetation ukros is performed in the territory where there are different obstacles. Stones, poles, benches, trees, etc.P. Flexible equipment when colliding with these obstacles only wears out faster, but the tool motor does not overload
  • Metal discs. Their purpose is to cope with a variety of difficulties in the field. They effectively mow thick and thick.Nisted vegetation. In a collision with obstacles, there is a rapid dullness of the teeth, as well as the overload of the power unit

many, fishing, line, trimmer, grass

Knowing the difference between steel disks and the cord, it is not difficult to decide what exactly is better to purchase. Trimmer fishing line in stores is sold in skeins with a meter of 15 meters. You can wind up from 4-5 meters of fishing line on a trimmer coil, which depends on its diameter. To save, you can buy a fishing line for a trimmer for a trimmer for grass in a bay, where its meter is from 250 meters.

It is interesting!When choosing a cord for a lawn mower, it is necessary to check the date of its manufacture. This is done to exclude the likelihood of buying outdated material. After all, nylon tends to refer and lose its original parameters. If the fishing line for a trimmer is stored for a long time, then do not dispose of it, and soaking the previous technical properties will help soaking in water or fat.

Preparation of a trimmer coil for grass for winding

Initially, as a rule, the coil is installed to the head of the device itself. The coil consists of two parts. This is a lid and a spring.

many, fishing, line, trimmer, grass

You can buy the highest quality electric ships, trimmers for grass and additional components here in the online store “Garden mechanisms” for the lowest for the selected goods from the category. The directory of the link presents the most popular, demanded electric mowers from world brands such as Bosch, Makita, Patriot, Gardena, Hyundai and others.

  • Whatever company you have a trimmer for the grass for preparation are the same for all types. Disassemble the device, or rather, remove the coil from the head of the trimmer for the grass. To do this, we click on the fixers located on the sides of the head of the head, and turn the head clockwise.
  • In order to open the mowing head without problems, click on the side latches, if you do not succeed with your hands, use a flat screwdriver to help you help. We take out the coil from the head.
  • In order to correctly choose a fishing line for a trimmer for your equipment, digital designations must be applied on the inside of the coil, which indicate the thickness and type of permissible fishing line. All designations are indicated, as a rule, in millimeters.
  • If you have not found any numbers, then the maximum permissible diameter of the fishing line can be determined by a through hole for lingering the fishing line. The fishing line for the trimmer should go forward and backwardly.

Two working antennae

In this type of squelpies, you should find the number of grooves for winding the fishing line lying on the inside of the coil:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.Captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. Inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded into them or hold the fingers of the free hand, spread into the through hole of the outer half of the bobin, the spool is locked and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each on their own groove, fixing antennae and assembly of the coil is similar to the option considered above with one groove.

The 1st implementation of this procedure may seem to be long and quite laborious, but over time and experience, this problem will be solved significantly more freaky and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. This operation is not a complicated one and, with some patience, will necessarily be crowned with success:

many, fishing, line, trimmer, grass

Fishing line for a trimmer. Varieties and the ability to replace other material

A cord for a trimmer for grass can be of different diameters (from 1.2 to 4 mm), and it must be chosen depending on which vegetation is required to mow. The thicker the fishing line is for a trimmer, the more rough grass it will cope. Experienced users recommend putting a fishing line for a trimmer 2 mm thick, which is a universal.

The shape of the fishing line can be round (for juicy grass) or with sharp faces in the form of a square or asterisk (for beveling dry grass). The second type is less durable and wear out faster compared to the round cord.

One of the popular issues regarding the work of trimmers is whether it is possible to replace a special cord for mowers with other materials, for example, metal or steel cables and strings, wire, etc.D. You need to know that the installation of such items is not recommended, because along with them the trimmer for grass turns into dangerous equipment. During the mowing, pieces of wire or metal will constantly break off and fly off in different directions, risking to injure the employee. And if you accidentally touch their limbs during work, a serious wound is provided.

Owners of trimmers interested in whether it is possible to use a fishing fishing line for a trimmer, we answer. This is allowed, but it will be much faster to tear and wear out, which means it is a frequent replacement.

Advice! The fishing fishing line for a trimmer is good for cleaning herbs near a fence or metal mesh-instead of spending an expensive trimmer cord, you can charge a large caliber tackle (2-3 mm), which is much cheaper.

Automatic winding of the fishing line on the reel

There is a variety of coils in which the automatic mechanism performs winding on its own. It is enough to correctly season the fishing line for a trimmer from the user. The fishing line for the trimmer is passed through the hole on the inside of the case, its antennae without winding are spread through the hole on the outer body, the bobbin is assembled, and when rotating the winding button for the trimmer, it is wound independently inside. It is impossible to make the winding incorrectly in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

When spring comes, people often spend their free time in a summer cottage. They try with the coming of warm days to free their own site from such difficulty as weeds and grass.

It is hard to do this manually, especially if the territory is very large, because the lawn mower will help. Thanks to this technique, there is an option to trim the grass and remove weeds. This is a suitable device to mow unnecessary plants near the fence, at home, between the rows in the garden on a flower bed, etc.D. What to choose a lawn mower that is suitable for your needs read here.

Best trimmer line on the planet

The cutting element in this device is a fishing line for a trimmer (strong polyethylene thread), which is wound on a special element. Coil. However, over time, the fishing line for the trimmer wears out and is necessary in its substitution.

The thickness of the polyethylene thread is depending on the model of the technique and varies from 1.4.5 to 4 mm. You will like it:

  • With a round section. This is the strongest material for mowing grassy plants;
  • With curly section. Used to mow soft plants;
  • Twisted. Used for narrow grass;
  • Professional type, is not suitable for all models of technology.

To change the fishing line for a trimmer on a lawn mower, you need to purchase a cutting thread that will be completely suitable to feel or another type of mowing.

You can soak the thread in a basin with water for a couple of minutes to increase elasticity and hardness.

The device of the element where the nylon thread is wound very ordinary. This element is called a reel. There are two “paths”. Upper and lower. There is a special partition with a recess among these paths. A fishing line for a trimmer is wound on all these paths. For earlier it must be stretched through the recess.

So that it is possible to remove the coil without obstacles, you need to unscrew a special button that is placed on the mowing housing.

It is worth noting that the coils in mowers are usually different:

  • For functioning with one osik;
  • For functioning with 2 antennae;
  • A fishing line for a trimmer should be extended through a through hole, which is placed in the snuffs of the element.

No need to confuse this part with an extension cord for a lawn mower on a coil, because despite the similar title, these are two completely different elements.

Small excavator technique of chainsaws is created for easy work and people who prefer to keep the device with the same hand.

This article will say to you what, how much does the ZIL 130 dump truck weighs what this transport is capable of.

Read here // MachinSpec.COM/Leszagotovitelnaya/Benzopila/Stanok-Dlya-Zatochki.Html, how to assemble a machine for sharpening chains of a chainsaw yourself swiftly and simply.

In the first version, wound the cutting element is very easy:

many, fishing, line, trimmer, grass

  • On the inside of the coil element there is a fixing ear.
  • One osik thread is inserted there.
  • The nylon thread must be refuel in the direction of the revolutionary rotation of the coil element.
  • It will come in handy from 2 to 4 meters of fishing line. When the winding process is completed, put the small end of this cutting element outward and fix in the groove that is needed to fix the fishing line so that it does not spin the functioning of the braid at the time.
  • If there is no special groove, then the end should be held with the hand so that the cutting element does not spin the upcoming element collection at the time.
  • At the final step, you need to pass the outer end of the thread into a special hole located on the outer part of the element. Subsequently, of course, insert the coil into a mower.

How to refuel a fishing line for a trimmer to a trimmer coil for grass?

The third method is suitable for refueling single.Section mowing coils.

Review of ECHO SRM 2510 petrol pumps how to start a trimmer, run-in, work correctly, subtitles

All actions should be performed in the following order:

  • First of all, it will be necessary to disassemble the spitter head, after which it is necessary to clean it of grass, fine debris and the remnants of the old cord;
  • Next, you need to cut off from the total amount of about 10 m new fishing line and bend it in half. As a result, one hand must hold both ends of the fishing line and the place of its fold;
  • After that, you need to find a recess in a spool. In a single.Section mowing head, it is located on top or below. Next to the notch there should be an arrow, which indicates in which direction to wrap the cord;
  • Then you need to start wrapping the fishing line. During installation, a fishing line for a trimmer should not bend or hang. Otherwise, she will constantly jump out of the coil;
  • After winding the cord in the hands of the operator, 2 ends should remain, 10-15 cm long;
  • These ends must be put into through holes located in the side walls of the upper part of the coil, opposite each other;
  • After that, you need to assemble the coil. In this case, her spring should definitely stand between two metal washers.

Trimmer for grass is the necessary and useful tool for a summer cottage and a private house. Many own and actively use it, but not everyone knows how to replace a fishing line for a trimmer in a trimmer, especially at first.

In this instruction, we will analyze the entire replacement process step by step. Looking ahead, there are two ways to refill a fishing rod with a fishing rod. There is no fundamental difference. The difference is that in the first case, one fishing line for a trimmer will be refueling, folded in half, and in the second there will be two segments of these forests.

The coil is worn out from long work.

The first repair project is to solder a new extension cover made of nylon or plastic.

In order for the saw to stay in the hole, it was necessary to clamp it in the cartridge of the lathe and cut the groove under the locking ring using a cutter with a depth of 1 mm and 2 mm wide.

I leaned over the stop ring onto a trimmed pipe of water from a bicycle needle and removed an additional place.

After a simple repair, I put my head on a bureau, put on a shoe, tucked a fishing line for a trimmer and went to the garden for testing. Everything is working! Correctly! I pressed the updated speech. Trimmer fishing line continued. After mowing, the dust remained in place. Planned surfaces are not clogged with grass and earth.

The successful decision over the next hour was re.Implemented on the second worn head. Now I have a spare!

If you carefully look at the attached drawings, you can guess along the bronze workpiece of the articular prosthesis “Tube plus tube”.

Or even with a protective cap on the trunk. Then a groove with a locking ring is not needed.

How to remove a fishing line for a trimmer

To replace a fishing line for a trimmer in a trimmer, remove the head cover. To do this, press the fingers of the latches of fixers located on both sides of the lid, and pull the lid up. Access to the coil will open. After that, pull it out, pulling up the axis on which the coil sits. If the ends of the fishing line stick out from the holes of the head, then lift the coil along the axis and pull the remaining fishing line from the holes of the head. Now the detail does not hold anything and it is easy to remove and remove the remaining working thread.

The coil is divided into two parts by the central partition with a neckline. Different models of cobs differ in size, so you need to check how much you can wind the fishing lines on the bobbin. Its length ranges between 1 and 4 m.

Summing up the above, we note the main factors affecting the choice of fishing line for the lawn mower:

When choosing a fishing line for a trimmer, pay attention to the shape of the section and the thickness of the product; Buy only those models that are suitable for a lawn mower; Give preference to manufacturers who have proven themselves in the market with quality goods; Wipe the fishing line for a trimmer thoroughly after work, so that the remnants of grass and dirt do not remain on it.

Remember that the hardworking character of the owner of the site will become clear already on a well.Groomed lawn in front of the house. When choosing a fishing line for a trimmer, listen to the recommendations of experienced summer residents.

| Denial of responsibility | Contacts |RSS