How to install a fishing line for a trimmer on a trimmer coil for Huter grass

Trimmer for grass is a suitable and desired tool for a summer cottage and a personal house. Many have and use it intensively, but not everyone knows how to change the fishing line for a trimmer in a trimmer, in particular, first.

In this annotation, we will analyze the entire substitution process step by step. Looking ahead, there are two methods to season with fishing trimmer rogue. There is no principle difference-the difference is that in the first case, one fishing line for a trimmer will be refueling, folded in half, and in the 2nd such forest there will be two segments.

The first way

The prepared segment (in this case, it is 4 meters) is bent approximately in half-one segment should be 15-20 cm longer, and inserted into a special gap located on a dividing partition.

A fishing line for a trimmer is wound in a particular direction. This is done in an interference, the fishing line for the trimmer is neatly distributed. In this case, you need to wind the segment, which is longer into the section, which is closer to the button.

There are designs in which there is no division of the coil into two sections. This does not change anything, the fishing line for the trimmer is wound in a similar way. It is only necessary to ensure that the segments do not overlap among themselves.

The first should end the segment that is located at the bottom of the coil, t.e. closer to the fixing holes.

This tip is placed in the corresponding diameter hole. Trimmer fishing line is reliably fixed.

A long segment wraps another half turn. There it is similarly fixed. At the same time, the segment crosses another coil section.

A long segment wraps another half turn

The fixed ends of the wound fishing line are inserted into the holes of the trimmer’s corps of the grass.

The fixed ends of the wound fishing line are inserted into the holes of the trimmer’s corps of the grass

The coil is attached to the body. The ends of the fishing line are pulled with force so that the fishing line previously recorded in the holes of the coil of the fishing. This is easily determined by the characteristic sound (click).

The coil with the button is snapped in the corps of the trimmer’s trammer for the grass.

The coil with the button is snapped in the corps of the trimmer’s trammer for the grass

The replacement of the fishing line was successfully made. In this case, you need to install it back on a trimmer for grass and you can proceed to the span of grass.

It should be repeated, you do not need to remove the spool from the trimmer for the grass. this was done to clarify the process of replacing fishing line. You can disassemble the rogue in place, wind it up and put it back.

The tips so that they do not beat the trimmer casing for the grass, you can and should be cut.

Method 2. two segments

The only difference from the method is no different from the method. two wound segments of fishing line, instead of one.

There are two special fixing nests on the coil (see drawing above).

They hook it previously formed on the fishing line, and begin to wrap a fishing line for a trimmer.

Winding is carried out in a special order

The winding needs to be carried out in the following order: first the lower fishing line for the trimmer, t.e. that which is closer to the fixing holes at the bottom of the coil, and only then the upper one, t.e. the one that will overlap the lower section.

The tips are made in the holes of the corps of the rogue trimmer for the grass. They are pulled to a click, which means that the fishing line for the trimmer has left the latch.

trimmer, coil, huter, grass, works

The tips are torn into the holes of the corps of the rogue trimmer for the grass

The coil is fastened into the case. The fishing line for the trimmer in the rogue is replaced.

Overview of a garden electric trimmer for Bosch AFS 23-37 grass

The order on the personal plot takes care of any owner of the cottage, cottage, or even an old lup. Before growing weeds, everyone is equal. Everyone monitors his own site in their own way. For example, my neighbor uses this way of weed fighting:

Every day he sets her a new area of ​​processing. Its main minus: the processing of selective, dried grass always remains untouched, and not everything to her taste.

With the development of modern technology, traditional inventory as braids for grass, hoe and shovels are gradually giving way to mechanized devices that not only greatly simplify labor, but also increase the speed and quality of processing of the site.

Today, the main character of our review will be one of these modern assistants: an electric garden trimmer for Bosch AFS 23-37 grass.

Model operating instructions

The above trimmer for grass gasoline “Huter” should be used taking into account the safety rules that are registered in the instructions. Of these, you can find out what to use equipment to persons who are under the influence of alcohol or physically tired are unacceptable. Before starting work, it is necessary to arm yourself with special means of protection, among them the appropriate clothes, protective glasses, mittens or gloves, helmets and headphones should be highlighted among them. Equipment should not be used near flammable and explosives. This also applies to the conditions under which high humidity remains.

To replace a fishing line for a trimmer in a trimmer, remove the head cover. To do this, press the fingers of the latches of fixers located on both sides of the lid, and pull the lid up. Access to the coil will open. After that, pull it out, pulling up the axis on which the coil sits. If the ends of the fishing line stick out from the holes of the head, then lift the coil along the axis and pull the remaining fishing line from the holes of the head. Now the detail does not hold anything and it is easy to remove and remove the remaining working thread.

The coil is divided into two parts by the central partition with a neckline. Different models of cobs differ in size, so you need to check how much you can wind the fishing lines on the bobbin. Its length ranges between 1 and 4 m.

Types of trimmer heads

A mowing head for grass is a cylindrical case in which a coil (bobbin) is inserted with a fishing line in it (cord). This design can be installed both on gasoline and electric trimmer. The heads differ in the method of refueling and supplying the cord and there are 3 types.

  • Automatic. The cord is supplied after the user reduces engine speed. Although the automatic supply of the fishing line is convenient if large volumes of work are performed, such rods have one drawback. a large thread consumption.
  • Semi.automatic. Using this type of head does not require complicated manipulations from the user. The principle of their operation is arranged so that the cord is automatically lengthened at a time when the device works at full speed. It is enough to slightly hit the trimmer’s head for the grass on the ground (this removes the cord lock), and the fishing line for the trimmer, due to the centrifugal force, moves out of the bobbin, after which it is cut to the desired length with a knife located on a protective casing.
  • Manual. For lengthening the cord, the device is required, after which the fishing line for the trimmer is handed out manually.

Based on the above, semi.automatic bobbins are the most optimal option. It should also be borne in mind that the coils for a trimmer for grass are one.built (used only to trim the grass) and two.string, which are used to mow high grass and small, with thin stems of shrubs.

Instructions with a step.by.step description how to wind the coil of a trimmer for grass and lawn mower

In order not to make a mistake with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the coil. This information is usually presented on a tip, which will not allow us to make a mistake using the appropriate equipment.

How to open a self.supporting coil (spool) motorcycles.

If the information on the coil about what diameter the fishing line for the trimmer can be refueled, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the equipment, it remains to figure out how to charge it. There are two ways for this, but not for all they are applicable. Consider both methods in details, and already depending on what models and trimmers you use, you are determined on your own which option is suitable.

It is interesting! The principle of how to wind a fishing line for a trimmer for a tip of motorcycles is appropriate not only for autonomous benzar groups, but also for electric trimmers.

Peculiarities

If you read the features of the models of this manufacturer, then to begin with, it should be said that this company from Germany was based on one thousand nine hundred 70 nine years. All the equipment that is produced under this brand is created by qualified engineers and developers and is being verified at every step of creation. In general, the lawn mowers of this German company are massive and fairly productive models. Their use allows you to cut grass in almost all criteria. Very often the best models of this company are used specifically for professional purposes. One of the fundamental features characteristic of all models of the manufacturer will be that motor.coats from Huter are equipped with a two.stroke engine with air cooling and electric ignition. This function makes it possible to ensure the highest power of the device and high.quality execution of the intended target.

The quality of the spark is determined by its ability to set fire to a correctly formed air-fuel mixture in working criteria. A weak spark in the criteria for lean pressure and temperature in the combustion chamber cannot do this. Ignition occurs later or does not occur at all. A bulge appears in the operation of the motor, the motor does not gain momentum, vibration, detonation appears, the “blast shock” effect may seem in the starter.

The insidiousness of this breakdown lies in the fact that the diagnosis below the above methods does not give 100 percent conviction of the performance of the ignition reel. Such implicit breakdown, when there seems to be a spark, but it is not completely true, often misleads and forces the difficulties with the ignition coil to a carburetor malfunction. Ordinary acts in such cases are an increase in the supply of fuel. It turns out that such a spark can set fire to the enriched mixture, but there is no correct. But the introduction of an enriched consistency leads to the rejection of the cylinder-piston group and muffler. Therefore, in such controversial situations, check both the carburetor and the ignition coil again.

How to wrap a fishing line for a trimmer for a trimmer for Huter grass

March 22, 2018. How to change a fishing line for a trimmer trimmer for grass and how best to choose. How to wind up a coil now let’s talk about how to wind. Trimmer for Huter GGT 2500S Video grass I bought a gasoline trimmer for Huter GGT2500S Hello Hello Hello everyone. Gasoline trimmer for Huter GGT 1300T HELL.

With a GGT-1500S gasoline trimmer, the arrow consists of two parts and can be easily assembled without tools

But if you do not need to transport the tool to the mowing position, you should pay attention to his “twin brother” with a strong bar GGT-1500T. The position of the handle on the trimmer is adjustable in height for the optimal balance

Shoulder belt bothers your hands as much as possible. Thanks to an effective anti.vibration system, prolonged work will be performed without excessive fatigue. The plastic case protects the operator from throwing grass, branches and stones from under the cutting block.

Features of a trimmer for grass Huter GGT-1500S-safety operation HUTER GGT-1500S Safe Operational Call prevents grass on the operator. Convenient control GGT-1500S Convenient control of the recover fuel tank. for convenient tracking fuel consumption. Convenient installation of the HUTER GGT-1500S tool, convenient installation of the tool, convenient bicycle handle of a gasoline trimmer for grass Huter GGT-1500S. for uniform natural movements of the operator during operation. Easy transportation Huter GGT-1500S light transportation.The advantages of the Huter GGT-1500STA engine are established. 1.5 kWhn both young grass and dense growth.Electronic ignition.Vibration extinguishing system.

trimmer, coil, huter, grass, works

How to change a nylon fishing line for a trimmer on a trimmer?

To fill the shock head of a lawn trimmer for grass with a nylon fishing line for cutting grass, the shock head will need to be previously removed from the drive shaft and disassemble.

The disassembly process is simple. There are visible grooves on the head of the head that actually indicate the fasteners. In these places of the cover of the lid, it is necessary to create a small pressure, while stretching the lid.

Operation on the analysis of the module case where the nylon fishing line for a trimmer is refueling, acting as a cutting tool of a trimmer for grass in the mode of cutting the grass of lawns

To lay a new nylon fishing line in a trimmer for grass, about 3 meters of material in each groove (6 meters in total), designed for this plastic coil. Previously, the coil is removed from the spindle with the spring and the puck. The remnants of the previously refueling nylon fishing line from the coil must be removed.

Next, take a pre.purchased nylon fishing line for a trimmer (diameter 2.5 mm), rewind 6 meters of the product, cut off a measured piece. The resulting segment of the fishing line for a trimmer for the grass is folded in half. The end part of the nylon fishing line in the place of a half bend forms a kind of loop.

Winding of nylon fishing line on the reel

At the next stage of the operation, the coil of the head of the trimmer for the grass of the lawn is grasped with the palm of the left hand, holding in the position, as shown in the picture below. With the other hand, throw the loop of the nylon fishing line into the protrusion of the central side, dividing the winding area of ​​the coil into two sectors.

Laying nylon fishing line in a trimmer for grass, or rather in the sectors of the coil. Loop version of the stop of the material before winding. Some trimmers for grass lawn (garden) have other options for the stop (mount)

Win both halves of the nylon fishing line evenly and tightly counterclockwise (or on the arrow indicated on the coil body). Stretch. wrap the slings without twisting one sling from the other. The winding ends when the residual ends of the nylon fishing line are about 150 mm long.

Then they insert the coil back into the spindle and pass the remaining 150 mm ends of the nylon fishing line into spindle grooves specially provided for these purposes. Then the spindle part of the assembly is rested on the palm of the left hand and on the opposite side of the coil is installed in the place of the washer and the spring previously removed.

The assembly process. installation of a wound coil: 1. the production of the remaining 150 mm ends of the nylon fishing line in special grooves of the spindle; 2. installation on the coil of previously removed elements

This is the replacement of the fishing line in the trimmer ends, the assembled module is installed on the drive part, as was considered above in the text. Meanwhile, many models of trimmers of lawn (garden) are also supplied with bush cutters, the use of which also requires installation procedures.

Trimmer coil device for grass

Cassyle heads for trimmers come in different designs. both simple and complex. The figure below shows a semi.automatic trimmer head from the Husqvarna motorcycle (Husqvarna).

This type of head is present in the configuration of most benzocosyles and electrimmers such as Stihl (Stihl), Patriot (Patriot), Champion (Champion), Bosch (Bosch), Huter (Huter) and others. The device of the braid head is quite simple. It includes the following details:

  • the base of the mowing head;
  • button for semi.automatic supply of the cord;
  • Spulk (coil), into which a fishing line for a trimmer is refuel;
  • spring;
  • eyes. through them a fishing line for a trimmer goes outside;
  • trimmer head cover;
  • Trimmer fishing line (cord).

There are also simpler trimmer heads shown in the next photo.

All these nozzles do not allow you to change the length of the fishing line in semi.automatic mode (after pressing the button). In the case of a break in the cord, you have to stop the mower and change it manually.

Trimmer coil device for grass

Cassyle heads for trimmers come in different designs. both simple and complex. The figure below shows a semi.automatic trimmer head from the Husqvarna motorcycle (Husqvarna).

This type of head is present in the configuration of most benzocosyles and electrimmers such as Stihl (Stihl), Patriot (Patriot), Champion (Champion), Bosch (Bosch), Huter (Huter) and others. The device of the braid head is quite simple. It includes the following details:

  • the base of the mowing head;
  • button for semi.automatic supply of the cord;
  • Spulk (coil), into which a fishing line for a trimmer is refuel;
  • spring;
  • eyes. through them a fishing line for a trimmer goes outside;
  • trimmer head cover;
  • Trimmer fishing line (cord).

There are also simpler trimmer heads shown in the next photo.

All these nozzles do not allow you to change the length of the fishing line in semi.automatic mode (after pressing the button). In the case of a break in the cord, you have to stop the mower and change it manually.

The main malfunctions of the coil

Users of the electrimmer and lawn mower often face a problem associated with a semi.automatic braid head. Coil malfunctions can be as follows:

The cord spontaneously lengthens

There are situations when a user of a trimmer for grass notices a very fast fishing line consumption. At the same time, he never hit the ground with a button to lengthen the fishing line. The reason that the fishing line for a trimmer spontaneously lengthens, cutting off a special knife on the casing of the device, may be the absence of a spring in a mowing head. Often beginner users of mowers, trying to charge a fishing line for a trimmer into a coil, forget to install a clamping spring in the head, or completely lose it when opening the lid, and in the future, they do not even suspect its existence.

Also, a fishing line for a trimmer can lengthen without using a button if the spring is weakened. If the spring check confirmed this fact, then it is necessary to put several goals under it to strengthen its clamping properties.

Materials:

From point of view. hacksaw canvases should not be completely red.hot.

Everything that is needed for the manufacture of the nozzle

First you need to make the base of the nozzle. For this, from a metal plate

Cut the square with a side of 100 mm. You need to mark it in such a way that there is a hole exactly in the center (at the intersection of the diagonals). To do this, from the center of the selected opening perpendicular to the short side of the plate, we measure a distance of 50 mm and plan the trimming lines.

Cut the excess and get a square of 100 mm x 100 mm. Now it is necessary to twist the corners a little and drill the central hole for the shaft of a trimmer for the grass.

Twist the corners and drill the central hole for the shaft of a trimmer for grass

Cut the canvases for metal, measuring from each end 8 cm. We get 4 blanks with finished holes.

The end of the screw must be blown up so that the nut does not fly.

Fishing lines winding algorithm

The procedure for winding the fishing line depends on the type of coil. with one or two antennae, as well as with automatic charging the cord.

On a reel coil

Winding a fishing line for a trimmer to a coil with one osik is very easy. In such structures, depending on the brand of a trimmer for grass, from two to five meters of the cord is placed. The edge of the fishing line in the spool must be tucked into a special hole or groove, after which the string is wound in the direction opposite to the rotation of the coil during operation.

After the fishing line for the trimmer is windpowed, you need to leave a small piece (15-30 cm), walk into the output of the spool and collect the head again.

To a coil with two antennae

In the rogues of this type, you need to inspect the inside of the coil and determine the number of grooves for winding the cord provided for in it.

For winding, you need to take a piece of fishing line with a length of two to three meters. For a spool with one groove, tie a fishing line for a trimmer into a through hole, combine a mustache, leve and wind it up in the direction in the direction of its rotation during operation. If fixing grooves are provided, they need to go through the ends of the cord, then stretch them into the output, and then close the coil and put them in the same place.

Read also: Sharpening drill at home video

For a two.lep mewood, the difference is that the section of the string should be folded in half. Next, it is necessary to charge the middle of the bend into the groove between the grooves, and then wrap each of the pieces of fishing line on its path, fix the antennae and assemble the coil as well as the spool with one track.

On a trimmer head with automatic dressing

For heads with automatic refueling, it is enough to just start and squeeze the edges of the fishing line, and the tool will perform further winding on its own when turning on. It is impossible to make a mistake here, because the coil itself recognizes how the antennae should be located.

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
  • Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
  • Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

How to disassemble and assemble a trimmer for grass

For an independent disassembly of a trimmer for grass, a set of tools is prepared:

Disassemble each node of the device separately for diagnostics.

Dismantling the electrimmer

Electric trimmer for grass consists of a main electric block and a rod. Consider how to analyze for the repair of the electric part:

  • Put an electric car on a flat surface.
  • Unscrew the fixing screws of the trimmer body for grass on one side.
  • Having removed the lid, you can diagnose, repair or replace the electric motor, drive and bearings, brush unit, launch buttons and other elements.
  • To assemble a trimmer ectric for the grass should be sequentially: first, install the motor by tightening the fasteners; connect an electric circuit; Gently lay the wires in the case in the corresponding recesses; Close the top cover and tighten the screws.

Dismantling of a benzotrimmer (the video instructions shows a trimmer for Gruntek BS 52x grass) for engine repair is performed as follows:

  • First you need to remove the gasoline engine from the rod.
  • Disconnect the starter by unscrewing the fixing bolts.
  • Remove the protective casing of the gas tank, and the tank itself.
  • Unscrew the spark plug and remove the outer engine cover.
  • Remove the carburetor, pipe, ignition and muffler from the engine.
  • In order to conduct diagnostics and replace faulty parts of the motor, first of all it is necessary to disconnect the clutch node. To do this, fix the combustion chamber, and with the help of a unit key, unscrew the fixing bolts of clutch.
  • After the repair, collect a motorcycle, performing the same action in the reverse order.

What trimmer do you use in a summer cottage, and whether to repair the tool yourself?

Solving possible problems with fishing line

Most of the problems associated with the fishing line are similar to different trimmers and are solved in a similar way.

The string is not advanced

In the coils of automatic and semi-automatic cords, the cord is served without stopping the trimmer for grass. If this does not happen, then:

The fishing line for a trimmer in the head is wound wrong, so the coil does not spin; The winding of the fishing line is made unevenly, so the cord stuck between the turns and does not go out. so that this does not happen, you need to wrap the thread carefully, preventing distortions, a turn to the turns; The ends of the cord emerging from the holes are very short, centrifugal force is not enough to extract them, so the fishing line is not served-before turning on the trimmer for the grass, it is important to control the length of the thread and slightly lengthen it, if necessary; The cord is stuck

How to remove or refuel a fishing line for a trimmer in a trimmer for grass

In order to wind a fishing line for a trimmer, it will need about 10-15 minutes. What is the coil of a trimmer for grass? A plastic case with a snot cassette on which there is a special hook for a comfortable winding of fishing line.

In fact, all the coils of trimmers have a similar principle of fastening, this is a central screw-button, when pressed, it becomes possible to stretch the fishing line for the trimmer of the required length. The photo below shows several examples of different coils for trimmers.

Bobbins of the trimmers, the motor of which is located near the ground, have a different fastening to the rotation axis, they have two buttons on the coil located at the edges that need to be squeezed, the rest of the thread is no different from the other cassettes.

String Trimmer Ignition Coil Replacement #545046701

The principle of proper winding of the fishing line is identical in all of the above cases, therefore, for example, we will see the standard option with 2 antennae.

To remove the coil with a fishing line, you need to unscrew the screw in the center, but keep in mind, the thread there will have to be twisted clockwise, it is specially made so that during operation it does not open under the influence of centrifugal force.

Further, using the screwdriver, to disassemble the head and pull out the coil, on which the fishing line for the trimmer is specifically wound.

Having measured the desired length and folding twice, it is necessary to season the fishing line for the trimmer to the coil, leading, ultimately, its ends opposite each other (for this there are special slots for fixation).

After that, you need to collect the head in the back, passing the ends of the cord in two corresponding holes.

If there are doubts or it is not completely clear how to charge a fishing line for a trimmer for a trimmer for grass we advise you to look: how to correctly wind the fishing line for a trimmer into a lawn mower.

How to reload a RYOBI 40V Trimmer Line

In this video, the instructor will thoroughly open the trimmer head in steps, measure the right amount of fishing line, usually from 2 to 4 meters, and demonstrate the assembly and installation for a trimmer for the grass.

| Denial of responsibility | Contacts |RSS