How to correctly charge a trimmer to grass

Since trimmers for grass are produced in a wide variety, the spills on them also have several types. They are classified according to various signs: if the user is necessary in the process of serving the string, according to the material of manufacture, by design (for semi.Automatic models) and by the method of winding the cord per coil.

For feeding the cord

By the method of serving fishing line, trimmer heads are divided into:

A manual coil appeared before other options. Its design is simple and reliable, but you need to unwind the fishing line for the trimmer to replace the used. To do this, you have to change the trimmer motor for the grass and stretch both ends to the suitable length.

The semi.Automatic coil allows you to lengthen the cord without turning off the engine, right during operation. To do this, you need to press the head to the solid surface so that the mechanism that releases the ends of the forest works. The centrifugal force unwinds the cord, and the person again raises the head of the device above the ground, when the length is sufficient. The whole procedure takes a matter of seconds.

The automatic coil works when the braid lowers the engine speed (the gas mower has such an opportunity, but not an ethletric trimmer for grass) or starts it. The fishing line for the trimmer is advanced until the user again increases the moment.

According to the material

According to the material from which the working heads are produced, plastic and metal coils are distinguished. For the manufacture of the former, shockproof plastic is used, for the latter. Aluminum and steel.

By design

Spilles of semi-automatic coils are one- or two-section. On a single.Section cord is wound evenly, the turns are distributed along one groove. Two.Sectional bobbins are divided in half, so that the fishing line for a trimmer is laid in two grooves, and when lengthening the working part, each end is fraught out of its compartment. For such a spool, the uniformity of the turns is not important.

By type of winding

By the method of winding fishing line on the bobbin, there are the following types of coils:

How to Wind a Trimmer Head

To refuel a collapsible bobbin, you will have to turn off the trimmer for the grass, remove the cutting head, get the coil from it, remove the remnants of the worn fishing line and manually wrap up a new one. Then collect everything in the reverse sequence and continue the mowing.

A quick.Shot reel is not required to remove the cord for wrapping. It is enough to draw the ends of the new forest in the holes on the coil body, wind it on the bobbin in the right amount and cut off the excess length or cut the loop.

charge, trimmer, coil, stihl, grass, fishing

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. Specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
  • Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
  • Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

How to replace the fishing line for a trimmer in a mowing head, coil of the motorcycles Stihl FS 55

How to correctly change the fishing line for a trimmer in a mowing head, a coil of the Motokos STIHL FS 55 online store store for

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.Captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. Inside the arrow is usually indicated the correct direction of the winding.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.Consuming, but over time and experience, this task will be solved much faster and easier.

charge, trimmer, coil, stihl, grass, fishing

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. This operation is not a complicated one and, with some patience, will necessarily be crowned with success:

A couple of tips

If the fishing line for the trimmer was wound correctly, then when pressing the button button, automatic stretching of the cutting element should occur. A trimmer fishing line for your mowing device is one of the most important elements, without which a trimmer for grass can lose all its functional abilities. We can say that a fishing line for a trimmer (cutting element) is the heart of your mowing. Therefore, when buying a fishing line, primarily devote to its quality. When purchasing a fishing line for a trimmer of a particular company, be sure to compare it with the quality of the old fishing line.

What can be used instead of fishing line

Most mowers are interested in others or sellers in specialized stores about what can still be used (replaced) except for the fishing line. Many of them begin to experiment and use unsafe methods, installing different cutting elements on their trimmer for grass, including copper wire, metal, some manage to use strings from guitars and even cables, and someone is completely a fishing line for fishing networks.

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. Specific actions will depend on the complexity of the configuration and the type of product itself:

String Trimmer Heads. Everything you Need To Know! Decoding Myths.

charge, trimmer, coil, stihl, grass, fishing

  • Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
  • Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack bobber. After disconnecting the nut, the whole bobin is removed.
  • Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

How to correct the fishing line for a trimmer to the coil of a trimmer for grass

The coils exist different. For a coil working with one osik, it is easier to refuel a fishing line for a trimmer than with others. In the inside of the coil there is a hole designed to fix the fishing line. You need to insert the tip of the fishing line into it and start wrapping.

It is important. You need to wind in the opposite direction from rotation of the coil in the trimmer. Look carefully, most likely in the same place, on the coil, the direction will indicate the direction where to wind

The winding can go from about two to four meters of fishing line. It depends on the size of the coil itself. At the end of winding, a small piece should be left free. He will protrude outside. In order to squeeze it, there is a groove that is the same on the inner surface of the coil. This groove fixes the end of the fishing line tightly and does not allow it to be unwound when collecting a coil. If the design of the coil does not provide for this groove, then hold the end of the fishing line with your hands yourself. Now you can attach the outer part of the coil. It also has a hole in which you need to pass the outer piece of your fishing line. Now you can return the assembled coil to a place for a trimmer for the grass.

Text about coils designed to work with two antennae. First you need to see how much there are fishing strokes on the coil. There is a presence of either one or two in different coil designs. And then it becomes clear how it should be wrapped. Two antennae at once in one groove, or each antennae in a separate

Please note that if there is one groove in your coil, then the hole for the fishing line should be through. Now you need to reinforce the fishing lines about 2-4 meters and go into this through hole so that the fishing line is the same on one and the other side

Now look again, there will be an arrow indicating where to wind. Direction. Against the direction of rotation of the coil in the trimmer. Wrap two fish outflows at once, together. Leave small ends. If there are special grooves. We pinch in them, if not, then we just hold it tightly with your hand, with your finger. There will be two holes in the outer body of the coil. For each end of the fishing line, a separate. Passed, collected a reel and put it on a trimmer for the grass.

If you have a coil with two grooves, then a won piece of fishing line (all the same 2-4 meters) should be folded in two, and in a special groove (it should be just between the grooves), insert the place of the cod of the fishing line, that is, folding it, folding her loop. Wind up, as in the previous case, you need both fishing lines at once, only this time. Each on a separate groove. And then. As described above. Fixed, attached the upper body, fixed the coil to the trimmer for the grass.

Another type of coils is with a through hole on its inside. There are holes on the external case. That is, it turns out that the fishing line for the trimmer must be passed through these holes in the inner and in the outside, and immediately collect the coil. And for winding, use a button (this is the same button that is used to release fishing line during operation). Just to wound a fishing line for a trimmer now you need to rotate this button. Over, the mechanism of this button is arranged in such a way that it can only be twisted in one, just the direction you need.

Fixcut and Durocat braids

Two more simple models for mowing and clearing the territory. Compatible with a number of strings of different sizes and shapes that are inserted manually. Durocat, unlike Fixcut, allows you to use not only two, but also four strings: the locations of the fishing line at this head are indicated by arrows.

Both versions are radically different from previous options in that the cutting strings in this design are simply inserted from the outside. Therefore, the question “how to wind a fishing line for a trimmer for a trimmer for grass” for owners of the corresponding devices is not entirely appropriate. In the modification of Fixcut, unfold and disassemble the head is not required. This is due to the fact that it is not equipped with a coil at all.

The described variety provides only the installation of cutting strings up to 20 cm long. Replacing the fishing line in the trimmer is carried out only with the engine turned off.

Varieties of fishing line in shape. What it affects and why they are different

Initially, the fishing line for the trimmer was produced only round in shape, but other modifications soon began to appear. Square, hexagonal, in the form of a star and others. They are still different in color, but the color does not affect anything, except for the visibility of cutting equipment during operation.

The shape of the string affects the type of mowing grass. In the shape of the cord there are:

  • Round is a common form that is still considered universal. The round shape of the string is divided into smooth and with turns. If a smooth string is characterized by noisiness of work, then twisted on the contrary works quieter, but its accelerated consumption is observed
  • Square and hexagonal. The presence of sharp corners provides a more effective cut of vegetation, which must be taken into account when processing large areas
  • Ribbed and in the form of a star. Even more effectively cut different types of stems, and reduce the load on the engine

Some craftsmen, when spent on the fishing line, replace it with a steel wire or metal string, which is unacceptable. The wire is not only capable of cutting the dense shoes of the roeer, but can also be wound on the head, which will lead to its jamming with the shaft. The jammed head will entail the wear of the transfer mechanism and the power unit.

The shape of the section Appointment Advantages disadvantages
Round For young and green grass only Cheapness, resistance to large loads, smooth cut and low consumption Noisiness during work, and is not suitable for dry and thick.Nisted grass
Quadrratic High green and dried grass Even cut of grass, lack of crushing stems Large consumption, quick wear, fragility and the possibility of use only on powerful trimmers
Star Dry grass and shrubs High.Quality and effective cut due to a large number of corner faces High cost, the possibility of using on the corresponding heads
Twisted round Any grass from green young to dried Effective cut of stems, high speed and performance, noiselessness Quickly wear out, hardly unwinds from the coil during operation

How to correct the fishing line for a trimmer to the coil of a trimmer for grass

The coils exist different. For a coil working with one osik, it is easier to refuel a fishing line for a trimmer than with others. In the inside of the coil there is a hole designed to fix the fishing line. You need to insert the tip of the fishing line into it and start wrapping.

It is important. You need to wind in the opposite direction from rotation of the coil in the trimmer. Look carefully, most likely in the same place, on the coil, the direction will indicate the direction where to wind

The winding can go from about two to four meters of fishing line. It depends on the size of the coil itself. At the end of winding, a small piece should be left free. He will protrude outside. In order to squeeze it, there is a groove that is the same on the inner surface of the coil. This groove fixes the end of the fishing line tightly and does not allow it to be unwound when collecting a coil. If the design of the coil does not provide for this groove, then hold the end of the fishing line with your hands yourself. Now you can attach the outer part of the coil. It also has a hole in which you need to pass the outer piece of your fishing line. Now you can return the assembled coil to a place for a trimmer for the grass.

Text about coils designed to work with two antennae. First you need to see how much there are fishing strokes on the coil. There is a presence of either one or two in different coil designs. And then it becomes clear how it should be wrapped. Two antennae at once in one groove, or each antennae in a separate

Please note that if there is one groove in your coil, then the hole for the fishing line should be through. Now you need to reinforce the fishing lines about 2-4 meters and go into this through hole so that the fishing line is the same on one and the other side

Now look again, there will be an arrow indicating where to wind. Direction. Against the direction of rotation of the coil in the trimmer. Wrap two fish outflows at once, together. Leave small ends. If there are special grooves. We pinch in them, if not, then we just hold it tightly with your hand, with your finger. There will be two holes in the outer body of the coil. For each end of the fishing line, a separate. Passed, collected a reel and put it on a trimmer for the grass.

If you have a coil with two grooves, then a won piece of fishing line (all the same 2-4 meters) should be folded in two, and in a special groove (it should be just between the grooves), insert the place of the cod of the fishing line, that is, folding it, folding her loop. Wind up, as in the previous case, you need both fishing lines at once, only this time. Each on a separate groove. And then. As described above. Fixed, attached the upper body, fixed the coil to the trimmer for the grass.

Another type of coils is with a through hole on its inside. There are holes on the external case. That is, it turns out that the fishing line for the trimmer must be passed through these holes in the inner and in the outside, and immediately collect the coil. And for winding, use a button (this is the same button that is used to release fishing line during operation). Just to wound a fishing line for a trimmer now you need to rotate this button. Over, the mechanism of this button is arranged in such a way that it can only be twisted in one, just the direction you need.

| Denial of responsibility | Contacts |RSS