Guide to Bending a Metal Angle

Sometimes it is necessary to trim a part or a product at a certain angle. As a rule, you need to trim baguettes, moldings, platbands, baseboards and similar interior elements at an angle of 45 degrees. Anyone can do it. The main thing is not to rush, not to be nervous, and everything will work out.

Buy ready-made corner elements

Of course, the easiest thing is not to torment with the trimming of this or that part, and buy ready-made, not in need of processing and trimming. Such parts and elements are now sold everywhere in large supermarkets or smaller stores.

For example, in the case of baguettes or fillets, they are sold as special corner elements that fit perfectly into the corner and do not need to be trimmed. They just need to be glued in place and pressed down well.

A few words about tools and materials

Floor skirting boards are now made of wood or polyvinyl chloride (PVC), simply put, plastic. Ceiling fillets have a slightly longer list:

The range of ceiling skirting boards

The range of ceiling plinths is much wider than that of the floor direction.

  • Polyurethane. these baseboards have good elasticity and can envelop radial and other curvilinear surfaces, but they need to be trimmed at precise angles in any case;
  • Foam. the easiest budget option, the price of foam skirting boards is low and they are cut very easily;
  • PVC. the principle is the same as that of the floor skirting boards, but the range is much wider;
  • Wooden. similar to the floor, only here there are still wide models;
  • Gypsum. with the advent of polyurethane and foam plastic, gypsum ceiling strips have become a secondary concern, firstly, they are heavy, and secondly, fragile. But to be fair, it is worth mentioning them.

As it is impossible to trim properly a ceiling moulding and its floor counterpart without a good tool, let’s dwell on this question in more detail.

The best, almost ideal tool for trimming any baseboards and skirting boards. this trim saw with a pivoting frame. The high-speed disc makes smooth and precise cuts, and the base of these units rotates to any angle. The only problem is the serious cost of this tool.

A coping saw is almost ideal for trimming baseboards and not only baseboards.

A shoe saw is said to be one of the best hand tools for accurately cutting small lumber. This is true in principle, but I’ll tell you honestly, it’s not easy to find a really good saw, even with today’s range. If you do decide to buy such a tool, buy a saw with a fine tooth.

A hacksaw is handy when working with a jigsaw.

Theoretically, foam plastic and polyurethane can be cut with any sharp and sturdy knife. But you need to have a steady hand and at least a little experience in cutting Styrofoam. Plus, it’s hard to cut wide bars with a knife.

Without experience it is very problematic to make a clean cut with a knife.

Personally, in the absence of a trimmer I only use a hacksaw for metal. It’s good for cutting any kind of material, from Styrofoam to wood. By the way, the question is often asked than to cut the plastic baseboard for the floor, so here. take a hacksaw for metal and you can be sure not to make a mistake.

For trimming baseboards hacksaw for metal is one of the best tools.

How to cut a baseboard at 45 degrees

Choosing a tool for shaping a corner

The most economic variant is a purchase of an ordinary plastic plastic wire cutter. It is a plastic block with eight working slots. Such a device is designed for only two operations: trimming at 45, 90 and 22.5 degrees. A 90 degree angle comes in handy when, for example, we need to cut a jack in the middle of the molding.

Some plastic plinths come with eccentric brackets. They are better, because it is easier to work with it. the base-plate is clamped in the right position, it doesn’t move during the cutting. Accordingly, the flaws, if any, are small and it will be easy to adjust the angle.

What to cut plastic skirting boards with: a standard plastic wire cutter

If you have to repair in your own home, then it is ideal for you to buy a more formidable tool. a rotary single-plane jigsaw. It is designed to cut at an angle of 15, 22.5, 30, 36, 45 and 90 degrees. This jigsaw is designed with 2 mitre saws.4 clamps. for clamping in the horizontal and vertical planes, and the limiter, which will allow you to cut the workpiece to one length. The hacksaw will be built in here. If it is not clear how to cut a ceiling plinth. the video review below will help you.

How to cut a baseboard in a corner: the rotary jigsaw

How to cut a ceiling plinth contains a detailed description of the rotary jigsaw, and information on how to use this tool.

How to cut the ceiling plintuss using a template chisel

Something resembling a power wire is made by drawing the necessary angles of cut on paper, cardboard, or wood. It is necessary to draw two parallel lines, find the center, and at the end set off the necessary angles using a protractor. The advantage of this method is that there is an option to defer any angle, including greater than 90 degrees. Naturally, before you cut the corners of the ceiling plinth, you must first check the angle between the walls with an angle and measure with a protractor.

The method of cutting a ceiling plinth with a drawn chisel is exactly the same, as well as with the chisel itself. We press the baseboard plank to one of the parallel lines, then set the hacksaw to the desired angle, which is already marked, and cut off.

How to cut a ceiling plinth corner with the wood joiner

The chisel is an ordinary carpentry tool that allows you to cut the workpiece at the required angle. Almost always represents a tray of plastic, wood or metal with vertical slots for cutting at an angle of 90 ° and 45 °. There are also more complex designs of the plinth cutter. for cutting at angles of 90, 60 and 45 degrees. For more professional work using a plane with a swivel mechanism, where the hacksaw can be fixed at any angle to the workpiece.

How to cut a ceiling skirting board with a wire cutter. the inside corner:

  • Hold the skirting board against the ceiling, measure the proper length.
  • Later we put the baseboard plinth in the jig so that the position coincides with the position of the plinth on the ceiling.
  • The baseboard is preferably pressed to the far wall of the skirting board.
  • Holding the skirting board with the left hand.
  • We choose the position of the hacksaw when the angle is 45 degrees and immediately the handle of the hacksaw is very close to the left hand.
  • We cut the workpiece without making excessive pressure on the saw.
  • The next step is to cut the counter trim strip of the plinth. Install it to the far wall of the cutter as well.
  • Press and hold with the right hand.
  • Choose a position for the hacksaw when the angle is 45 degrees and the handle of the hacksaw is close to the right hand.
  • Cutting the baseboard.

Next, we dock the cut skirting boards and check the accuracy of the cut. For a more accurate orientation still say that to perform the inner corner must begin to cut the front of the baseboard. The wood skirting boards after trimming most likely still have to be fitted with a file.

How to cut a ceiling skirting board by means of a wire cutter. the outer corner:

  • In order not to make a mistake with the size, it is better to start with the marking of the inner corner, and then already cut the outer corner. Otherwise, it is possible that the length of the skirting board might be insufficient.
  • It is necessary to attach the slat to the ceiling and mark out the dimensions.
  • Install the ceiling plinth trim and press it to the nearest wall.
  • Hold with your left hand and choose a 45 degree angle position for the hacksaw when the handle is close to your left hand.
  • Cut the workpiece.
  • We establish a mating plank to the nearest wall, we hold by the right hand.
  • Hold the hacksaw at a 45 degree angle with the handle close to your right hand.
  • Cut the workpiece and join the corner.

Trimming billet with the help of a stool is suitable only if the angle between the walls is even. 90 degrees. In this case, the precision is not civilized enough, you will have to use other methods.

Composition and features of the material

To understand how to correctly cut a baseboard, you should understand its composition. This will help you choose the right tool and cutting technique.

  • Styrofoam. The cost and strength of this material is the lowest. But because we are creating a decorative ceiling decoration, the strength is not particularly required.
  • Styrofoam ceiling plinth is denser. than ordinary foam plastic. To cut such a material is used the most common knife.

READ How to Cut Skirting Foam Ceiling Corners

Tip: Sharpen your knife well before use. This will free from the presence of jagged edges in the cut areas.

Tip: The flatter and more frequent the tooth of the saw, the more even the edges will be. Even a metal blade can be used.

Introduction of a regular hacksaw blade

Cutting without tools

How to cut the corner of the ceiling plinth without a joiner? It is possible to perform the calculation and the cut manually.

Enough to make a good marking on the ceiling, then cut exactly the right angle. A significant disadvantage of this option. in inconvenience, when you have to hold hands all the strips in the process of measuring. In general, this method is no worse than helping to make the necessary measurements.

When you put the product to the place where it will be mounted, you can immediately take into account all the errors on the walls.

First, two blanks are cut at an angle of 90 degrees. Then apply one of the slats, pointing it perpendicularly to the wall. Guide the trimmer line along the ceiling, outlining the desired contour. Then remove the slat and attach a second. for reciprocal marking. The intersection point of the straight lines will be the place of the cut. Then the place for the future cut is marked on the slats.

The best way to cut the ceiling baseboards in the corners, experienced carpenters, joiners and builders. Most advise to make cuts on the side and try on the strips to the ceiling, if necessary. trim in the direction of adjoining parts to the surface.

Having made the rough docking, finally screw the finished skirting boards to the wall. Joints are sealed. the installation of the skirting board is complete.

Ceiling skirting serves as an excellent means of masking the various irregularities that are bound to occur at the joints of the walls with the ceiling. The result is not only a visually even corner, but also a fairly aesthetically pleasing completed interior.

An important point in fixing the ceiling plinth is to measure and cut it correctly.

So, let’s consider how you can cut the ceiling plinth.

To begin with, let’s define what a ceiling plinth is, and what it can be made of.

For the manufacture of ceiling plinth strips different material is used. It can be sufficiently flexible polyurethane, wood, styrofoam, PVC.

The most durable, stable and flexible are considered polyurethane skirting boards. By the way, it is worth noting that this element of the decor has its own name. the fillet. Because it can be confused with moldings, which are attached to the flat surface of the walls or ceiling.

The use of decorative corners

We mean the special corner adapters, which are usually equipped with polyurethane and polystyrene friezes. Decorative corners are glued to the very corner, and baguettes are attached to them on both sides. Adjustment in this case is either not required at all, or is carried out with a simple office knife.

Finished corner elements

In order not to engage in trimming ceiling plinths on their own, you can use ready-made solutions. In any construction store you can find factory-made products, already at the factory made at a certain angle. Such an angled piece allows you to connect the edges of the plinth, simply cut at right angles. Corner details allow not only to connect the tack in the corner of the ceiling, but also to hide the imperfections of the cut on the edges of the details.

Unfortunately, this method is not relevant in all situations. Dimensions of the corners, manufactured at the factory, are adjusted to certain standards. but the skirting boards themselves do not always meet the standards. Of course, such parts can be combined, but the result will not look aesthetically pleasing. If corners of a suitable size are not available on sale, you will still have to do the trimming of baseboards yourself.

And what tools to use?

Basically, either option uses the following construction elements:

As a rule, road accessories are made of heavy concrete to ensure maximum traffic safety for both drivers and pedestrians on adjacent sidewalks. Such designs are made by vibration. It is this method that distinguishes road systems with increased resistance to various weather conditions and durability.

The placement of concrete road products is carried out with the help of special road equipment.

Concrete paving products are laid with special road equipment. This provides a more even arrangement of construction materials and, consequently, a high strength of the resulting casing.

First, it is necessary to prepare the trench for the future border. A device that can be used to dig a trench will help. Or use an ordinary shovel.

Another, no less important for curbs fasteners. trench. This will make the ditch even.

There, on the compacted surface, put gravel or crushed stone and pour concrete mortar on top, on which such an element will be placed. After the curbs are displayed, they are fixed with concrete. All you need to do is observe the width of the joint between the side concrete stones: it should not exceed 5 mm.

| Denial of responsibility | Contacts |RSS