A guide on how to bend a metal angle

Sometimes it is necessary to cut a particular piece or product at a certain angle. As a rule, you need to trim baguettes, fillets, platbands, baseboards and other similar interior elements at a 45-degree angle. Everyone can cope with this task. The main thing is not to rush, not to be nervous, and everything will work out.

Buy ready-made corner elements

Of course, the easiest way not to bother with the trimming of this or that part, and buy ready, not in need of processing and trimming. Such details and elements are sold today everywhere in large supermarkets or smaller stores.

For example, in the case of baguettes or fillets, special corner elements are sold that fit perfectly into the corner and do not need to be trimmed. They just need to be glued in place and pressed down well.

Other Ways

With a good eye and accuracy of action of the hands can use a homemade template, which resembles an imitation of a jigsaw. To do this, take a narrow board or thick plywood and draw a layout in the form of a horizontal rectangle. Using a protractor, mark 45° on the right and left sides of the rectangle. Draw a scythe line connecting the opposite edges.

Now you can cut the ceiling plinth using this layout. Actions are ordinary and similar to the description above in the first option. Only the ceiling pieces should not be inserted, but overlaid on the outline and co-operate with a hacksaw to mark the layout.

Description of methods for attaching ceiling skirting boards (moldings) on the ceiling. The method of gluing by means of glue, putty and sealant. How to make even corners on the ceiling.

How to fix plastic corners?

First note that before the direct installation of plastic corners on the windows it is necessary to wallpaper the room, paint, etc. That is, you can start attaching them only after all the finishing work is finished.

You will need the following tools to install a plastic corner:

  • assembly glue (liquid nails)
  • masking tape (adhesive tape), and in a room with high humidity. silicone sealant
  • Metal scissors or a hacksaw
  • a pencil
  • PVC corners directly

Finishing windows with plastic corners consists of several steps. Let’s look at each of them:

Depending on where you use the plastic corners may be tapered, with L or F. shaped section, unequal, T-shaped profiles. L Corner.L. shaped profile is most often used in comparison to others. Basically it is masking slots in the joints of materials, edging sheet material, the corner joint trim.

As a rule, the angle between the shelves of the angle is equal to 90 degrees, and they have sizes: 1010, 1515, 2020, 2525, 3030, 4040, 5050 millimeters. Such corners are most often used for window and door jambs. If you install them in a place with considerable influence of environmental factors, it is better to use angles of 20 mm and more. or higher. Smaller corners 1010 and 1515 are usually used for finishing work indoors, they blend in with the overall design.

Plastic corners with unequal section are used for finishing arches. The sizes of such angles 517, 1020, 1525 mm. Angle with this section is easier to attach, they are flexible enough and easily maintain the desired position, creates a smooth line for trimmer bend and smooth edge. On one side of these corners has a section that allows you to make a line for the trimmer bend of the required degree.

PVC corners vary, depending on the type of finishing work. So they can be exterior and interior. Outside corners have an angle of 90 and 105 degrees. When using 90 degree angled corner for a window, one slat remains in sight, and the other is inserted into the gap of the window frame. Corner, which has an angle of 105 degrees, is mounted with two shelves outward.

See also  How to install a corner grinder on a chainsaw. The nozzle on the chainsaw is fixed

Self-adhesive plastic corners are especially popular. They are quite versatile, t.к. There is no need to buy glue. They also have an increased ability to bend and unbend, providing easy installation and a perfect look. One more specific feature: such corners are sold in rolls, the length in a roll is 50 meters. This allows you to purchase the necessary length and avoid joints.

Plastic corners on soffits: easy to install!

Plastic corners are the most modern and incredibly popular way to decorate plastic windows. The entire installation process is not difficult and it can be handled by a person without special skills. For convenience, you can divide the entire installation procedure into three main steps:

  • preparatory work with the surface to be treated;
  • Preparation of the corner;
  • The proper installation of the already prepared plastic corner on the surface.

If you are confident that you can do all the work yourself, then using the simple tips you will easily do the conceived.

corner, degree, angle

Corner notching

How to cut ceiling baseboards in the corners? The secret to a quality cut is to make the cuts on both the outer and the inner side. The inner cut is important if we make the outer corner.

Usually use professional equipment. crosscut saws or electric peoratorov industrial purpose. But supporters of home repair can do with the usual tools. The main requirement. at the end of the work the result should be clearly visible texture for the cornice, reflected on its front or back side.

Cutting method with a wire cutter

The most popular attachment option is using household tools. The chisel is a well-known carpenter’s helper, helping to make the cut at the right angle. Usually it is a tray, wooden or plastic, which has vertical slots for the blade at angles of 45 and 90 degrees. How to cut the corners of the ceiling plinths with a plier?

To begin with, place the material against the ceiling, set its slat in the jigsaw.

In doing so, the tool must coincide with the position of the product. Holding the baseboard with the left hand, choose a position for the cutting tool (hacksaw) at an angle of 45 degrees. Slices the material without excessive pressure. After that, cut a counter bar, set to the far wall of the mash.

Holding the working material with the right hand, select the position of the hacksaw at 45 degrees and cut.

The baseboard chisel

The carpenter’s chair is a device for cutting at a certain inclination. It is used with a hacksaw. In principle, you can make a plinth saw yourself by assembling a guide from boards and making cuts in the walls. On sale there are different models costing from 15 to several hundred dollars. They differ in capabilities, materials, although all are called a “plinth”. Professional models are made on the basis of a good hacksaw, have a scale that allows you to expose the saw as necessary. With such a tool, it is not a problem to set any desired angle of cut to properly cut the baseboard for a perfect junction.

Start installing baseboards in one of the corners. If this is your first experience, choose a part of the room where you want something to stand. Not always, of course, the first pancake, but still better to insure. To make the corner on the baseboard accurately, work without haste. One sawed off, checked, adjusted. Move on to the next. It is better to fasten after the two adjacent corners are assembled. But do not put off assembly too much either.

Trimming the baseboard in the corners requires some skill. But having made a few joints yourself, you can beautifully design complex corners

How to Use a Jigsaw to Cut Baseboards? Position the device in front of you, preferably on a table, but you can also on the floor. What side to turn it does not matter, it is symmetrical. Insert the skirting board in the profile, rotate it as it will stand against the wall. When sawing a skirting board in the jig, the wall that is farthest away is the “wall”. Once again: you press the baseboard tightly against the back wall in the position in which it will be installed. Insert the hacksaw into the appropriate slots. You can start sawing.

The first joint in the room

The first plank of the skirting board must be cut as close to the edge as possible. Carpenters have their own lingo and they say “cut” a corner. It does not matter what you call it, it is important that the bar is set so that to make the cut at the beginning. Push the trimmer piece of fishing line a little slack, if necessary 1-2 cm to begin with. It’s harder to cut a smaller piece, so save it for later when you have some skill.

See also  How to sharpen a drill with a corner grinder.

Position the skirting board in the jig at the far wall, facing in your direction. This way it is easier to check if you cut/saw correctly

Then do the corner on the skirting board like this:

  • We put the skirting board in the jig, press it against the wall opposite to us. Place it in the installation position. how it will stand against the wall.
  • Insert the hacksaw into the required slots (see the picture below).
  • Push the slat slightly beyond the trimmer line of the cut.
  • Cut off.
  • We take the second piece of baseboard, repeat the same operations, but the position of the saw on the jigsaw is reversed. Insert the skirting board from the other side. Be careful here, otherwise you will have to redo it several times, because the connection will not work.
corner, degree, angle

How to cut a skirting board properly in a jig: for external and internal joints

We got two pieces cut to fit in the inside corner. To make the joint perfect, try on parts in place. There are most likely some imperfections. We take sandpaper with medium grain, remove everything that prevents the docking. Then using fine grit we achieve a tight joint without gaps and gaps.

When joining skirting boards in a corner, we use a transparent silicone sealant. Before installing the fasteners, a layer of silicone is applied to the cut. Immediately after the skirting board is fixed, remove any excess that has appeared on the outside. Clean up to a completely clean surface. This method of connecting baseboards in the corners looks more accurate, no dirt and dust gets in it.

How to file the corner of the skirting at the right distance

The second and all other corners of the skirting boards must be done at a certain distance. If the next angle is again internal and the distance to it is less than the length of the board, we use the same piece with a notch already in it. We measure the distance with a tape measure. strictly from corner to corner. Then the distance is marked off on the strip using the same tape measure. Align the start of the tape measure with the ledge, measure the required distance and mark it with a pencil. It will be the starting point for the cut.

It’s important to know how far to cut

The skirting board with a mark is put in a wood joiner, choose the necessary direction of sawing. The line can be aligned with the hacksaw blade or with the slit in the jigsaw. Whichever is convenient. Cut off. This piece should be “tried on” in place. If both corners rest against opposite walls or the gap is only 1 mm, everything is normal. You can cut the second slat from the new piece to make the joint. Remove the imperfections again with sandpaper.

If the length of the wall is longer than the length of the baseboard trim, take a new trim. We will cut the second corner on it. It is important not to make a mistake which way to cut. Having set both boards along the wall, on one of them to mark the place of connection, make a straight cut. For straight cuts, there are also slots in the jigsaw. So there will be no problems.

See also  How to cut ceramic tiles with a corner grinder. Cutting curly or rectangular holes

How to cut corners on windows AURAMM.RU

How to cut a corner of the ceiling skirting

In one of ours, we told you how to glue the ceiling plinth on the wallpaper by your own. And in the contact form came the question. how to cut the corners of these baseboards. There is a question. there is an answer. The following is what remains to do our client carefully learn.

Perhaps the most difficult step when gluing ceiling plinths is cutting and matching corners. For this procedure you need to prepare beforehand a hacksaw blade and a plane. To cut unconventional corners, t.е. than simply or less than 90 degrees, a construction knife with interchangeable blades comes in handy. In most cases it is necessary to cut inner corners, because they are the corners of the room.

How to cut an inside corner

For cutting inner corners the baseboard needs to be inserted in the plane, its edge should be pressed a little bit further than the right 45 degree marking and cut with the hacksaw blade. It should be noted that if the longish part of the ceiling plinth on the left, and the trimmed corner is expected to the left side, if the right. the right side. It’s best to cut two corners at a time to check accuracy. Next, they need to be attached to the corner of the room, where they will then be glued. If the angle of the room is 90 degrees, then there should be no problems with gluing, but if there are inconsistencies, the baseboards can be carefully trimmed with a construction knife. After all the preparations, the ceiling plinth can safely be glued.

How to perfectly trim the corners at 45°? Tips for working with plastic.

How to perfectly trim a 45° angle? Tips for working with laminate. Trimming corners with one hand! Quickly.

How to glue plastic corners on the soffit

Kraftool metal scissors for cutting plastic corners. How to glue plastic corners on.

How to cut an outside corner

External corners in the room are somewhat less common than internal. It is also very easy to cut. Only in this case, all the rules will work the other way around. Т.е. first the beginning of the outer corner is marked, then the skirting board is placed against the marking and the corresponding marks are made on it. Next, the ceiling skirting board is inserted into the mortar, and its longest part should be on the left. The corner is cut at the left 45 degree marking. The right side of the corner must be cut similarly to the left. Before gluing the skirting boards, they must be docked on the outer corner, where they will be glued. If the skirting boards fit together normally, you can proceed to gluing, and if the angle is uneven or formed inaccuracies during trimming, they can be carefully corrected with a construction knife.

How to cut a custom corner

The most difficult process is to cut irregular corners. Sometimes during the installation of baseboards there are even rounded corners, which is very difficult to work with. How to act in such cases? If the corner is rounded, the skirting is best cut into several parts. Usually four or five pieces are enough. Next, each part of the skirting board needs to be cut at an angle on both sides. At the beginning of a rounded corner, the skirting must be flat. Parts of the skirting board are cut at the right angle and joined together. If necessary, they need to be carefully trimmed with a construction knife. After gluing the skirting board, it must be cleaned, treated with acrylic sealer and painted.

| Denial of responsibility | Contacts |RSS