How to get a chainsaw

Those who purchase a chainsaw for the first time may not know all the nuances of its use. The tool is dangerous and it is important to act carefully and competently. They begin work with familiarization with the instructions. And several additional points will allow the use of the inventory efficiently and safely.

Before making the first launch, it is necessary to check the condition of all parts. Use the tool, without making sure of its serviceability, is prohibited. Start with fuel preparation. Gasoline should have an octane number of at least 90. The most suitable-AI-92. Otherwise, low.Quality fuel will have a negative effect on the engine. Two.Stroke oil will be required. It is recommended to purchase a suitable for a specific chainsaw model.

The ratio of the components for the mixture is spelled out in the instructions. On average, the proportions are 1:33.

Fuel can be ethylated or unearthed. The first is used for tools whose engine is not equipped with a catalyst.

Then the refueling is carried out. It is better to prepare the mixture in a metal container. Start with the addition of oil, then pour gasoline to it and bring it to uniformity. The resulting composition is poured into the gas tank carefully so that the mixture does not get on the case. The lid is tightly closed.

The finished fuel is stored for a maximum of a month. Then the oxidative process begins.

It is necessary to check the tension of the circuit. To do this, in the middle of the tire it is pulled. If the tails of the links remain in grooves for at least 2/3 of the length, then the elements are installed correctly. The movement of the chain along the tires should not be difficult. It is also necessary to prevent excess tension of the part. To do this, it is enough to rotate the chain manually on the tire. If there is no sensation of strong tension, rotation is normal, then the installation is correct.

Then proceed to installing a hand brake. It is in front on the tool case. The lever must be squeezed forward so that after starting the chain does not start rotation. For the product to move, the manual brake is returned to the opposite position. Before starting the model, it is put on the brake.

It is also important to fix the product on a flat surface. This will allow him not to twitch when the engine is launched.

Chainsaw (Chainsaw) in rust

A chainsaw in the rast is the most effective tool for wood production, but at the same time also the rarest. This item allows you to extract a tree in huge quantities in the shortest possible time. Literally seconds go to 1 tree, and it is not necessary to beat on vulnerable points.

When obtaining wood using a chainsaw, you are guaranteed to get 100% of the tree. Even if you use an iron ax, which is often used in wood mining, you can get only about 87%.

Chainsaw

Kent’s McCulloch Eager Beaver 3.4 Oil Tank Replacement, Chain Sharpening Test Run!

Preparation for launch

Before the first launch of the chainsaw, you should check the condition of the saw headset and the quality of the bolts tension on the case. After that, prepare the fuel mixture in the proportion indicated by the manufacturer, properly pour it into the tool tank. You can’t start work without making sure of the complete serviceability of the device. This can lead to a breakdown of expensive elements, serious injuries.

Preparation of the fuel mixture

For normal operation of the chainsaw, it is recommended to take gasoline with an octane number of at least 90. The best option is the AI-92 brand, the use of less high-quality fuel can cause tapping of the engine, a decrease in its productivity.

For both running.In and constantly working, two.Stroke engine oil is required. It is better to purchase brands designed for specific chainsaw models. The proportions for the preparation of the fuel mixture for each saw are indicated in the operating instructions, it is recommended to mix on average from the calculation of 1:33. For old domestic chainsaws, the mixture is prepared in a proportion of 1:15.

Important! Ethyl fuel is used to refuel chainsaws with an engine without a catalyst. Its presence can be determined by the green lid of the gas tank, for models with a catalyst you need to fill in unhealthy gasoline.

Refueling

The mixture for refueling is recommended to be prepared in a metal container. First pour the required volume of oil, and then dilute it with gasoline and bring it to uniformity. Gently pour the prepared composition into the tank of the chainsaw, trying not to stain the housing, tightly screw the lid. The finished mixture can be stored for no more than 30 days, after which the process of oxidation is launched. At the same time as refueling, it is recommended to check the oil tank for lubrication of the chain, supplement it if necessary.

See also  Chainsaw idles at idle speed

Checking the chain tension

To check the tension of the chain on the saw set, just pull it with your fingers in the middle part of the tire. The shanks of the links with proper installation should not exit the grooves by more than a third of the length. The circuit should calmly move along the tire without severe efforts, if the movement is difficult. The tension should be loosened.

It is easy to adjust the voltage of this element in the chainsaws with the help of a special lamb bolt on the case. Some models have two bolts, less often the key is required. Before the start of operation, you should carefully read the instructions.

Features of the first and subsequent launches

Learning to start a chainsaw in principle is not difficult. The necessary skills are acquired directly during operation.

The launch of the chainsaw is carried out by a cord starter, in most modern models combined with an inertial or spring light system. Properly adjusted mechanism reduces the effort required to start the engine, almost half.

Since it is impossible to start a chainsaw without a starter, to extend its resource, it is necessary to develop a smooth, with a slight acceleration, the jerk of the cord, which does not create large loads on the design of the starting device.

  • For the first launch, the tool filled with fuel and chain oil should be installed on an even base, unlock the system for preventing random launch and the emergency stop of the saw headset. If there is a primer, you should pump fuel into the carburetor.
  • To start the engine, you should install a gas drive for small revolutions and, holding the tool by the handle, pull the starter handle. Start a chainsaw for the first time, which is called from half a turn, most likely it will not work. Even a completely working and adjusted tool “grasps” from 3-4 attempts.
  • At the idle mode, the piston group and a connecting rod-crown node work in conditions of oil starvation, so the idle time of the idle must be limited to a minimum.

.Why the chainsaw is not started?

If you did everything according to the instructions, and the chainsaws will not start, then something is wrong with her. This may be the fault of several of the most common reasons: there is no spark; fuel is not supplied; Air filter is closed. So, below we offer the procedure that will help to identify the reason why the chainsaws are not started.

Procedure if you don’t start a chainsaw

The first thing I would like to note if you don’t start a chainsaw is not twisting any screws on a carburetor. If you are not a specialist, then you still can’t set up something yourself and start a chainsaw will not work.

The following actions necessary, in order to start a chainsaw, take in the indicated order, starting to take action under the next number only if the previous one did not help.

  • For starters, just just leave the chainsaw at rest for 5-10 minutes. Perhaps during the factory she got a candle. This happens. Then try to get it according to the instructions again.
  • Remove the case cover on the chainsaw, remove the air filter and try to start without it. If the filter is contaminated, then it should be washed in soapy water and dried or replaced with a new.
  • Twist a spark plug from the chainsaw. Check the presence of a spark. If there is no spark, then try to put a new candle. If the spark never appeared, then this means that the ignition unit is damaged and the saw must be carried for repair. True, the visual observation of the spark does not mean that the ignition unit is working. If there is a spark, but the chainsaw did not work out, do the following on the list of action.
  • If there is a spark, but the candle is wet, then turn the chainsaw to drain excess gasoline from the cylinder if it accumulated there. Tighten 10-15 times a starter without a candle to ventilate the combustion chamber. Procate the candle and twist it back, or better change it to a new one, if there is. Try to start again according to the instructions.
  • If the candle is dry, then pick up one or two cubes of the gas mixture in the syringe and pour it into the cylinder. Try to have a chainsaw. Maybe a small snorinka got into the carburetor, which prevents the fuel from getting into the combustion chamber. This synchill will quite possibly eliminate the stream formed after the launch of the chainsaw by adding fuel directly to the cylinder.
  • Unscrew the muffler and remove it, trying not to spoil the gasket between the silencer and the engine. Try to get without a silencer and air filter. With the muffler removed from the chainsaw, you can inspect the piston from the inside. If there are burrs or bullying on the walls of the cylinder or piston, or the ring on the piston is clamped with burrs, then it will have to be very upset, as this means that the piston is damaged or worn out. This usually happens with underfilling in the fuel mixture of oil. With such a malfunction, you will have to contact the service, and it is possible to think about buying a new chainsaw, since replacing a piston is a fairly expensive operation.
See also  How to properly sharpen a chainsaw chain with a machine tool

Thus, we made out in this article how to start a chainsaw “according to the instructions”, and also what to do if the chainsaw is not started. We hope that these tips were useful to you.

How to get a chainsaw: a sequence of actions

It was noted that the surface on which the device is installed should be even. But you also need to make sure that the tire does not contact the ground.

Squeare of actions when starting:

  • The chain brake is turned off.
  • To turn on the ignition, use a special button or switch.
  • The flap supplying air is transferred to a closed position. To fix the lever in a similar intermediate form, it is pulled.
  • The front handle is taken with the left hand and pressed a little down. The right handle has a protective shield. It should step on him.
  • With a free hand, the handle is pulled to itself. It is recommended to act smoothly. As soon as the dogs of the mechanism with the clutch of the drum occur, you need to make a sharp jerk.
  • When the first outbreak appears, the air damper returns to the previous position. Run the tool again.

When the engine began to work, you can add gas and release the lever responsible for the throttle.

How to keep a chainsaw

To carry out the correct launch of the chainsaw, an important point is how the saw is located at that moment, more precisely, how the operator holds it. Two options for proper retention of the saw at the time of starting are allowed.

First option: the saw is installed on a flat surface, the operator’s left hand is straight and holds the saw by the upper handle, the right leg is set to protect for the right hand and presses the saw to the ground.

In this position, the operator is as convenient as possible to launch the tool, t. To. The right hand is free and at the same time the tool is securely fixed.

Before the launch of the saw, regardless of the position in which it will be carried out, it is necessary to enable the brake of the saw chain.

Option Second: the operator stands, the left hand holds the upper handle of the saw, while the rear hand closed the operator between the legs.

This position allows you to easily start a low.Power saw, and at the same time reliably fix it, warning itself against accidents.

chainsaw

Before you get a chainsaw, look so that there are no people or animals in my immediate vicinity to it.

Watch the video how to start a chainsaw and clearly study the actions when starting you can be below. In the video, a specialist of the company STIHL talks about how to work as a tool correctly, and to launch it on the example of the Stihl MS 211 chainsaw video is very informative and contains reliable information from the manufacturer.

chainsaw

How to keep a chainsaw

To carry out the correct launch of the chainsaw, an important point is how the saw is located at that moment, more precisely, how the operator holds it. Two options for proper retention of the saw at the time of starting are allowed.

chainsaw

First option: the saw is installed on a flat surface, the operator’s left hand is straight and holds the saw by the upper handle, the right leg is set to protect for the right hand and presses the saw to the ground.

In this position, the operator is as convenient as possible to launch the tool, t. To. The right hand is free and at the same time the tool is securely fixed.

Before the launch of the saw, regardless of the position in which it will be carried out, it is necessary to enable the brake of the saw chain.

Option Second: the operator stands, the left hand holds the upper handle of the saw, while the rear hand closed the operator between the legs.

This position allows you to easily start a low.Power saw, and at the same time reliably fix it, warning itself against accidents.

Before you get a chainsaw, look so that there are no people or animals in my immediate vicinity to it.

Watch the video how to start a chainsaw and clearly study the actions when starting you can be below. In the video, a specialist of the company STIHL talks about how to work as a tool correctly, and to launch it on the example of the Stihl MS 211 chainsaw video is very informative and contains reliable information from the manufacturer.

Stihl chainsaw preparation for work

How to use a chainsaw: step.By.Step annotation

The owner of a personal house, a cottage in another summer cottage sometimes need to create wood cuts. In this case, you need to purchase special equipment. Chainsaw Sometimes it is inconspicuous inventory. So that the work takes place rapidly and non.Hazardous, you need to join the detailed annotation of this process before the operation of the equipment.

How to use a chainsaw. Each master needs to know. If you do not make the rules discussed by the manufacturer of similar equipment, the highest risk of production injuries appears. Therefore, before operation, the subtleties of the equipment should certainly be carefully seen to our client.

Equipment features

Starting the study of the issue of how to use the chainsaw “Husqvarna”, “Stihl“,” Friendship “or other varieties of such equipment, you need to think about especially every tool. Our client remains the existing varieties conditionally divide into three groups.

See also  Chainsaw chain oil how to replace it

The first class includes household appliances. They are used in personal operation in the performance of a small volume of work. Such chainsaws have low power. However, for the home master of such multifunctional abilities there will be many. These are relatively cheap and light equipment.

Semi.Professional chainsaws allow you to bring down trees. Applying them also create a system or repair work. The working time of the tool does not exceed 8 hours during the day.

Profic chainsaws are able to work up to 16 hours per day. Their continuous operation is achieved by 9 hours. This is expensive, heavy equipment. Of course, choose it only to purchase a special company, enterprises.

Features of domestic chainsaws

Russian instrument has certain design features. In order to correctly operate them, you need to study the device of chainsaws. The most all-terrified instruments of this category are “friendship”, “friendship-altai” and “Ural”. They are in the field for a long time.

The Forest | HOW TO FIND THE CHAINSAW | Updated Location

To realize how to use the chainsaw “friendship” and other brands, you need to see their device. The equipment has an engine and clutch clutch, and a gearbox is also found. The saw apparatus. To be able to manage the work of the starter, special structural elements are provided.

The power system has a gas tank, carburetor and a crane. Samotek fuel enters the gas pipeline with an open crane in the carburetor. Removable starter launches the engine. These accounting systems work properly to ensure the usual functioning of the equipment.

Features of foreign chainsaws

Very popular now are the chainsaws of the brands “Husqvarna” and “Stihl”. Their device is similar to Russian types of tools. But in their device there are several features. They should be studied, ahead of time before using the chainsaw “Stihl” or “Husqvarna”.

The presented equipment of foreign companies is relatively small in weight. This makes work significantly more comfortable. The Khuskvarna has a gasoline suction function. This is well suited if the situation has occurred when the gasoline ended and the engine stalled. With subsequent refueling, this function will allow the saw to start a saw.

“Stihl” has a quick.Removable cover, which is practical if the passage of filling the candle with gasoline. Devices with a lid on bolts cause certain difficulties. In this case, the fasteners must be performed using only 1 screw. Foreign equipment is characterized by a huge set of additional functions. But the operating rules for all varieties of chainsaws are common.

Preparation of the tool

Considering how to correctly use a chainsaw. You should start with a detailed study of the manufacturer annotation. The subtleties of equipment operation remains here to be indicated by our client.

Before starting work, the tool needs to be checked. Start by tension of the chain. For this purpose, you are pulled by the upper link. In the correct version, the shank leaves the groove for a few mm. At the same time, the lower section of the chain should not sag. Otherwise, the chain should be pulled. After which it should stretch just. Strong tension is also unacceptable.

Stihl chainsaw (stihl). How to use

How to refuel it true. What oil to use. Principle of operation. How to start correctly. A little story.

The handle of the inertial brake should not in contact with the main handle. Otherwise, when the saw is working, the clutch will shift. Elementary primary check can significantly reduce the likelihood of equipment breakdown.

Refueling

Considering how to use the stihl, Jonshed, Husqvarna, Partner and other models, you should pay attention to the refueling process. Almost all of the devices presented have a two.Stroke engine. He is not able to work on a pure gasoline mixture. Therefore, fuel is prepared from certain components.

To prepare fuel, you need to take 1 liter of gasoline 20 g of engine oil. Gasoline should be A92 for domestic tools and A95 for expensive foreign models. The recommendations for the choice are indicated in the instructions by the manufacturer.

Motor oil should be specially designed for a chainsaw. Ordinary car varieties in this case are not suitable. In a plastic container, you need to stir oil with gasoline. The resulting mixture must be poured into the tank. Its hole is indicated by the gas stitching icon. The neck of the container for the oil is indicated by a drop.

Lubrication of the chain

For the equipment to work for a long time, and its functioning is of high quality, it is necessary to periodically add grease for the chain.

Most often, manufacturers recommend using only branded oils. If the user decides to use a different tool, you can replace a special lubricant with car varieties.

The viscosity of such a product must correspond to the level indicated by the manufacturer.

After choosing the correct lubrication, you need to understand how to use a measuring container for a chainsaw. The marks are located near the neck of the gas tank. When working with the equipment presented, it is necessary to periodically control the oil level inside the saw.

| Denial of responsibility | Contacts |RSS