A belt for a trimmer for grass from China. characteristic and design of the product, price, video

Hi all! Well, soon the summer season will begin)) Sourcelessly without “mowing” on the site can not do. A neighbor in the country acquired a “ran” belt for its Khuskvarnna last summer, says that it is much more convenient than shoulder! So I decided to buy myself too, but so far I have not decided which one is better? There are just with “straps”, there are soft straps, there are some kind of casing. In general, if there are happy owners of the background belt, please advise the model and company. And in general, the opinion is interesting, is it necessary?

With my champion T514, this included. Support on both shoulders, plus soft lining under the lechi. The braid itself for grass is attached to the side and rests on a wide plastic plate. Result: a rather difficult braid for grass becomes very convenient to use. Hands are occupied only by lifting/lowering the head (almost without effort, if the hook is placed in the center of the corner of the bar) and turning back to the left and right. I think the most convenient way of suspension of a trimmer for grass. Structurally, the Champions of Champions.

Last season, he drank a heavy Chinese scythe (42 cubes) with a standard shoulder belt. The shoulder was quickly tired, and the design itself is apparently not successful. For this season, I bought a Solo satchery belt until I mowed, but I pulled Motokos on it:. Much more comfortable. Having harvested very quickly, one big buckle on her chest is put on it and that’s it.

Someone visited the back of the back of the straps?

I tried this, according to it, distributes the weight more to the lower back than on the shoulders. We have the price in n.N. About 1 tyre. I can sell for 500 r.

Dima80 I set it up incorrectly, align the lower belts. The backpack is good, 4 hours of work, only the legs are tired.

I have already cut off such a suspension for 2 seasons, the braid for the grass is heavy, almost 8 kg. If you fit well, does not grate anywhere and does not press. Before that I used Hitachi, also good, comfortable. But Stilevskaya (from the 130th) personally seemed less convenient to me, the Germans saved on some trifles. I also tried the champions, that is generally liquid, no matter how you drive it. it hangs out. They wondered how to sew a comfortable suspension on his own. She sews bons professionally and all that, in short, understands how such things do. Well, in principle, you can sew, but there are a lot of muddy. The material will go off rubles at 300-400, special. Sewing machine is needed (or manually with a nameplate), and a free heap time.

How to wear a trimmer belt for grass correctly

Working a trimmer is much more convenient and easier to use a special belt. Thanks to him, the operator can mow large sections of grass without pain in joints and muscles for several hours in a row. The design of the biceps belt is designed so that the lawn mower is kept using the mounts itself. without the help of hands. She will only need to set the direction, and she will do everything else herself. About how to correctly attach a belt to a trimmer and set it up for yourself to facilitate the load, and it will be discussed in this material.

Many models of trimmers are equipped with an ordinary oblique belt. However, for work, it is best to purchase a rug belt, which is specially designed for motorcycle. Thanks to a thought.out design, it evenly distributes the weight of the device for the whole body. The shoulders with a soft lining reduce the severity and relieve pain in the forearms. The hard back disperses the load between the upper and lower backs, excluding the lower back. The impact.resistant protection for the thigh prevents the contact of motorcycles with the foot so that it does not rub and transmit vibration. In addition, the belt provides:

  • Convenient transportation of a trimmer for grass;
  • Comfort during operation due to the ergonomicity of the spit position for grass relative to the body;
  • Safety in work. the paraphernal belt prevents the slipping of motorcycles from the hands at the time of the stabs of hard objects.

Types and differences of cutting nozzles for motorcycle

Most often, lawnmands are used along with cutting fishing. The latter can have different thicknesses, however, regardless of this parameter, all the fishing lines available on sale are used mainly to mowing young grass.

If the gardener needs to mow large weeds or clear the old dry shrubs, then in this case you will need to use a knife for a trimmer for grass. Metal or plastic can be used for its production. The metal product is used to equip more powerful motorcycles, while a plastic cutting element can be installed exclusively on electric and gasoline trimmers for grass, with a capacity of up to 1.2 liters. With.

All knives available on sale are divided among themselves according to the number of teeth for cutting.

On sale you can find cutting elements with so many teeth:

  • 2 teeth. this knife for motorcycles is designed to mow young and soft grass;
  • 3 teeth. a cutting element is used to mow young solid grass and small weeds;
  • 4 teeth. products of this type are well suited for quick feed blank;
  • 8 teeth. a suitable knife for fast blank of dry grass and straw;
  • 10 teeth. this device is designed to mow thick wild shoots and young shoots of wild trees. Most often, this shift knife is used by housing and communal services for clearing densely overgrown sections along roads and railway tracks;.
  • 24 tooths. this shift knife for a trimmer for grass quickly and efficiently clears the shrubs, as well as the stem stalks of weeds;
  • 26 teeth. used for low and even mowing of large old weeds and shrubs;
  • 40 teeth. designed to cut young trees, the thickness of the stems of which does not exceed 3-4 cm. The cutting nozzle of this type has a rather large weight, so installing it on an electric trimmer for grass is not recommended.

Knives, in the design of which there are more than 40 teeth, are called discs. The disk for the lawn mower is most often installed in cases where the gardener needs to quickly remove the thick shoots of large weeds and wild shrubs. In most cases, the discs for a trimmer for grass are used only with a sufficiently powerful tool. These cutting elements with carbide attacks easily cope with young shoots of trees, the thickness of which reaches 5 cm.

The main malfunctions of the starter of the trimmer for grass

It is not difficult to determine the cause of the breakdown of the starting device. There are several main options:

These details are shown in the photo below.

It may happen that the starting mechanism will be accidentally broken. The consequences will turn out to be deplorable if the ragged rope is wound around the flywheel of a working internal combustion engine: then the spring bursts, the pulley will tear off. But such cases when a complete replacement of the starting node is required, they rarely occur. In most cases, to fix the mechanism, it is enough to put a new spring or replace the cord.

How to dress a motorcycle

Redverg 5014460 Belong belt for hanging a trimmer for grass. With the protection of the thigh. Bought for a chamber for Champion grass

Small video about kosba by a benzotrimer / benzocosa on the example of a student: how to dress a belt, like a balancer.

Electric trimmer for grass with the upper engine location (Stiga)

Using such a trimmer for grass, you can successfully fight weeds and mow everything, up to swan, burdocks and shrubs. The release of the fishing line here is semi.automatic or manual, the diameter of the fishing line is from 1.6 to 2.4 mm.

The undoubted advantage of this category of trimmers is that now you can safely mow and raw grass without afraid to get moisture on an electric engine. However, in no case should you mow during the rain!

Battering trimmers for grass are also not very noisy, they are easy to run and stop, you can freely move along the lawn, but the shortcomings are low cutting, larger weight (up to 4.5 kg) and a short time without recharging. from 15 to 30 minutes. Therefore, they still do not find wide application.

Gasoline trimmers for grass are widely used due to their autonomy, high power and performance. It is these devices that are most often used by professionals in their work.

When using a gasoline trimmer (benzocosa), you do not need to worry about the presence of a network outlet and the quality of the network voltage, be afraid to accidentally cut a cable-purple or melt their landing.

According to the layout of the lawn mower (however, partly this applies to electric trimmers) differ among themselves:

  • engine power and type (two.stroke or four.stroke);
  • a rod shape (straight or angular, solid or detachable);
  • the shape of the control handles (D, J or T-shaped);
  • cutting tool (trimmer head, disc knife).

The braids for grass with a four.stroke engine are favorably different in that gasoline and oil are poured into the engine, as in a car. separately. The preliminary preparation of a two.stroke fuel mixture from gasoline and oil is not required.

To divert large areas, it is more correct to use braids for grass with straight bar and T-shaped handles that distribute the load on the hands more evenly. It is desirable that the engine power is greater.

Work by a gasoline trimmer with T-shaped handles (Stihl)

Many, especially women, when choosing a trimmer for grass, are inclined in favor of powerful electric trimmers to not cope with the launch of a gasoline engine with a hand starter. But recently, these fears can be left aside. The breakthrough was made by the American company MTD, which equipped with engines with AST (Advanced Starting Technology. advanced launch technology). These are not just long.known solutions. for example, built.in decompressor or injection of enriched fuel mixture. In engines with AST marking, an additional device with a powerful spring is installed, the energy of which helps to start the engine without tension of the hand and even with slow pulling out the starter cord.

Starter cord stretch for starting the engine of the lawn mower

When buying a trimmer for grass, you need to determine in advance exactly what problems you want to solve with its help. After all, work under the bushes, the processing of the edges of the lawn and flower beds, the mowing of grass along the fence impose different requirements for the tool. Affect your physical data. The weight of the chosen model depends on them. is it necessary to need a background or you can hold a trimmer for the grass all the time by weight. And if several people will work with the scythe, then the height adjustment is needed.

Trammer for grass with straps and various options for a pansial device (STIHL)

When comparing various models of trimmers, the following indicators are distinguished: power; ease of starting the engine and supplying additional fishing line; Convenient location of the governing bodies.

The effectiveness of a trimmer for grass can be evaluated according to such an indicator as the ratio of mass and power. It is desirable that as much power as possible fall per unit mass of the tool.

Pay special attention to the ergonomic structure so that the law of law is not hard labor. The more convenient the handle or steering wheel steers for grass, the higher not only its handling, but also security. Fastening belts significantly reduce the load on the hands during operation, a fairly long detachable bar allows you to increase the coverage area, and if necessary, without problems, transport the tool in the trunk of the machine.

How to put a belt on a lawn mower

The comfort of the gardener and, as a result, the speed and duration of its work, depends on the correctness of the mounting of the motorcycle belt. Many do not want to spend time adjusting the fasteners of a gasoline trimmer for grass on a biceps belt, and it is possible that it is justified if it is necessary to jam the grass only in a small section or near the fence, but with large areas the issue of convenience and endurance will become primary if we do not want to stretch the mowing on several days. In addition, the correctly adjusted attachment of the lawn mower will make the mowing of grass significantly safer. As for me, then you should figure out this issue.

Installation and adjustment of fastening of a gasoline trimmer for grass. Backpack belt.

The convenience of use depends not only on the proper placement of a gasoline trimmer for grass on the backyard belt, its equilibrium, but also on the correct installation and adjustment of a two.handed handle, often called a bicycle.

Motokos mount adjustment. What to strive for.

After the adjustment of the two.handed handle and the backpack belt, the cutting tool of the lawn mower, which is in the hanging position on the strapping, should be parallel to the ground, the hands should not touch the garden tool. Height, of course, may vary depending on the task performed, 20-30 centimeters with a mowing of high grass for feed, 5-10 centimeters for cutting lawn grass.

Balanced a motorcycle with an installed cutting tool: a disk or a reel with a fishing line.

Adjusting: Running belt / backpack belt / belt of a backpack type / shoulder belt / parachute belt.

It is possible due to the inaccuracies of the translation, now you can find many names of the belt suspension of garden technology: the rain belt / belt backpack / belt of a backpack type / shoulder belt / parachute belt. For the lawn mower, only a biceps belt is suitable, hence the associations with a backpack and a satchel, which should be correctly attached and fitted by the figure. You can certainly hang on one strap garter, a belt of a loop, but I do not recommend it, except for very low.power models. Weight and vibration will quickly make themselves felt.

First of all, it is necessary to adjust the height of the hook of the biceps belt in accordance with its height. To do this, we put on the paraphernal belt and pull the shoulder belts so that the hook is below the hips to the width of the palm, and the load is evenly distributed along the straps. If you pull up a trimmer for the grass above, then only narrow the grabbing of the grass, and the cutting tool will most likely be at an angle to the ground.

We hang a motorcycle. Reducing the hook into the desired hole of the bar we balancing the gasoline trimmer for the grass so that the knife when releasing hands is on the chosen, depending on the tasks, height.

On those models of a gas station that are equipped with a loop for fastening, not a bar, it is necessary to carry out balancing, moving it along the bar.

hang, trimmer, belt, correctly, hook

The purpose of such balancing the distribution of the weight of a garden tool through a backpack belt on the shoulders, and not its constant support with hands. Hands should only set the direction of the cutting tool.

Then it is necessary to adjust the two.handed handle of a gasoline trimmer for grass. If the balancing of the garden tool is broken after that, then it is necessary to repeat all the stages, until the result is achieved.

It is not always possible to get the perfect balance of the lawn mower on the backward belt. Sometimes the parallelism of the knife of the Earth can be achieved only with the personal selection of length and replacing the standard rod of the trimmer for grass. Do not forget that the center of gravity will still affect the amount of fuel in the motorized engineering tank. But not even perfectly carried out adjustment of mounting motorcycles can greatly facilitate the work of the operator.

Instructions for replacing and adjusting the lawn mowing belt

Replacing and adjusting the tension of the drive belt of the lawn mower is performed in case of wear, destruction or stretching. Signs of wear. these are cracks, sticking threads, tears, uneven abrasions, absent teeth (on gear belts). In accordance with the recommendations of manufacturers, checking the state of the gas mowing drive mechanism must be carried out every 50 hours of operation.

How to fix a disk or a fishing line for a trimmer on a trimmer

The cutting mill is attached to the executive organ. The mounting location is called a gearbox. It is not difficult to cope with the task of installing a disk or coil. The principle of consolidating cutting discs on the trimmer is as follows:

  • The figured washer is originally fixed by using a hexagonal key
  • On the shaft set the disk
  • Then install the upper washer, and then tighten it by means of the fastener
  • It is necessary to rotate the nut through a special end key, which is usually equipped with each tool
  • The rotation of the nut is carried out in the direction counterclockwise
  • When rotating, it is necessary to jam the shaft with a hexagonal key

In the opposite sequence, the disk on the trimmer is removed and replaced. details on how to install a coil with a fishing line on a lawn mower is described in this material.

Replacing the belt in the Samsung washing machine

The following factors can serve as the reason for the replacement of the washing machine belt:

  • The that appeared in an incomprehensible noise in the process of work;
  • During a visual examination, the belt seems to be in place, but near the places of passage of the belt, as well as on all below the lying planes, tyrs is found resembling dirt, and to the touch resembles a washing elastic band (also rolls into spools);
  • The life of the washing machine is 6-7 years (the term of the drive belt).

The reasons listed above should give you the idea of ​​a preventive technical inspection, or maybe the repair, which is expressed in the replacement of the drive belt.

This article will describe the process of replacing the belt on the Samsung washing machine (Samsung). On all models of this brand, the back panel is not removable, which significantly complicates the repair.

How to adjust in a correct way an ERGO-Pro harness

  • Purchase a similar belt (you can by marking on the belt itself, you can provide the old option as a sample);
  • Island (a small piece of about 10-15 cm);
  • Wire (diameter 0.5-0.8 mm, length about 0.5 m);
  • Kusachki;
  • Flashlight.
  • crosshead screwdriver

Next will be a scheme according to which it is best to install a belt.

Replacing the belt in the following sequence:

  • First of all, inspect the drive gear and pulley of the drum drive of the car. You should note that the gear has grooves for retaliatory grooves at the belt and, as a rule, in the process of long.term operation, a trace is formed from the previously installed belt. It is recommended to install a car belt for a machine of this model on top. Therefore, keep in mind that when placing a belt on a drive gear, you need to try to get to the place where the previous belt was. If you shifted the belt too close to the end of the gear, then you will not understand as it will be installed on the pulley of the drum and it may turn out so that part of the belt on the pulley will hang or will be on the edge. Then you will have to dismantle and do everything again, taking into account the initial positioning on the gear.
  • After you placed the belt on the drive gear, you need to place the belt on the pulley, from the side of which the drive gear is displaced. Look at the diagram and you will understand what it is about. Bringing the belt to the top point, you need to choose this position of the pulley when there is a support from scrolling the fastener element. The fastening will not be able to fix the belt from the thicket, it will strive to shift in the direction of the opposite from rotation and will be stopped by the emphasis.
  • To fix the belt, use the island to exclude damage to the belt wire during installation. Then reliably fix the wire on top of the island. Make 5-10 turns and fix the edges with a twisting together. After that, we rotate the pulley towards installing the belt.
  • After the final installation of the belt on the pulley, there will be a characteristic click of the belt and further rotation will not be possible, since the belt will go to the gear, but our latch will stop it. We twist in the opposite direction and remove the latch. All. the installation of the belt is over. The process itself takes about 20 minutes, if you put the belt on the gear right correctly. You can check this by scroll through the pulley for several revolutions. The belt will take its position on the pulley and leve over the position on the gear. And then see how you like it.

In case of dismantling, you need to move the belt with your hand at the place of transition from gear to pulley, in the direction of rotation before the pulley and rotate the pulley. The belt must jump on its own.

In addition, 2 people are desirable here, as an option, you can put the machine to one side, be sure to the powder by the powder by the water, otherwise the remaining water can get to the board. One person will hold a belt on the pulley (and not on the gear) of the engine, and the second will pull the belt from above. Then the car can be lifted, and, supporting the tension, put on the pulley pulley.

What you need to know about the device of the electrimmer before the start of its repair: 2 types of structures

Trammers for herbs for mowing herbs with power supply from electricity are made with a capacity of 300 watts to 2 kW with two modifications. They are distinguished by the location of the engine:

Such products are created for different tasks, differ in weight, power, working characteristics. The first types of models are light and used to process the complex relief of garden paths under the bushes, near the flower beds.

Products with the upper engine arrangement allow you to process large areas, they are noted with high performance.

Both types of mowers can work from a household network 220 volts. However, elite products are created with food from the built.in portable battery. Most often they are used on light models, as shown in the photo above.

hang, trimmer, belt, correctly, hook

An example of a product with an upper engine and its layout show it in the photo of my Eco GT-800L below. The fastening of the belt allows you to hang a mower on the shoulder, and the handle provides convenient control of the cutting head during kosbe.

The working body is a spitter head with a fishing line. It can be supplemented with a cutting knife made of metal or plastic on powerful models. The torque of high revolutions for it is created by an electric motor, and it is transmitted by a kinematic scheme located inside an integral bar.

In more detail, the insides device show a photograph of the engine with the upper lid of the case on its trimmer. It is not equipped with a gearbox. This, by the way, is such a simple execution completely suits me.

The engine is turned on by a small final switch with a convenient plastic lid placed in the lower handle.

Features of the device of the electrical circuit: Briefly

The basic part is a typical collector engine in which the rotor of the stator windings gives the rotor to the bearing of the bearing.

The electric current that performs the main work flows through the closed circuit of all windings through the brush-collection mechanism.

The vast majority of engines as a protection against overheating of the insulation of windings use thermorelene. During the repair, we consider it as ordinary power contact in a closed state.

With a critical heating of the varnish of wires, it will simply open and interrupt the action of electric current.

All elements of the electric circuit are connected by wires and terminals to each other into the sequential site. A short cable with a fork is displayed out to connect to an extension cord.

the best electrimmers for grass in price and quality

Due to the fact that the market is full of similar units, it is very difficult to choose the right option. This article discusses in detail the 9 best models that are as suitable for giving

Particular attention will be paid to their main characteristics, configuration, advantages, disadvantages, as well as quality, reliability, average price

STIHL FSE 71

A convenient and reliable ectric trimmer for grass, which is suitable for trimming lawns with a stronger sedge, removing it around trees, benches, stairs in a small section. Able to put in order the territory with any neglect. They can even cut small lawns. Light in circulation, powerful, works from the network.

Thanks to good heat protection, the engine located in the upper part is not overloaded. There are 2 handles, one of which is rubberized and regulated under the growth of the user. There is a trimmer head that does not allow the configuration of the fishing line when replacing it.

  • Not basking.
  • The presence of protective glasses.
  • Light weight (4 kg).
  • Convenient adjustment of the handle.
  • No belt in the kit.
  • It is impossible to install a knife.

A rather attractive element of the site today is the lawn. However, it will look good if you care for him. To do this, you should regularly water the territory, feed with fertilizers and cut the grass weekly. If you neglect the last condition, then quite quickly the territory will turn into dense thickets.

trimmer for grass in action

So, the preparatory stage is over, it’s time to start work. Where to start? How to use all the capabilities of the device correctly? Of course, you can simply start work and learn the whole method of trial and error, or adhere to simple, but correct recommendations and get a wonderful effect after the first mowing. There are nuances everywhere, whether it is a haircut of a lawn, a saw of bushes with a disk or a mowing of grass for hay. You should start from the simplest.

How to cut the lawn so that it turns out to be even

The lawn implies an open even area that excludes some large landscape irregularities (pits, hills). Of course, snags and stumps should not stick out of the ground. their uprooting should be borne in advance. It is best to plant a place under the lawn with soft varieties of grass, which are good to mowing. In this case, you will spend much less effort.

  • Experts recommend dividing the entire area into small squares and mowing along them, moving from one to another clockwise. In this case, the grass that you mowed always remains on the left, and will not interfere with further manipulations with the trimmer.
  • If you need to mow “under the root”, then the angle of contact with the surface should be at least 30 degrees. With this technique, the device is practically in contact with the surface with a cutting knife.
  • There is an opinion that in order to give the lawn of the completed type, it must be mowed by a lawn.type lawn mower. This is partly so, but having adopted, you can achieve good results and with a manual trimmer. To correct the shortcomings after the work of a trimmer for grass, it is also recommended to use hand scissors for grass.
  • The lower the fishing line for the trimmer will be, the more even the lawn will be. Leaving the grass higher, it is likely that in different places it will be molested in different ways. This is due to the fact that the trimmer itself for the grass is not fixed on a horizontal plane, which leads to irregularities during the reciprocating movement performed during operation.

Kosim under hay

Harmity for a village resident is a necessity. this is animal food in winter, fertilizer and covering material that protects the landing from cold weather. Of course, with such a versatility of use, the question arises about a man’s advance harvesting. Kosba for the workpiece differs from the usual aesthetic cleaning of the perimeter in some features.

Brush Cutter Harness

  • For example, in order not to grind the mulch, you need to mow under the root, lowering the bar with the disk as lower.
  • The bums should be outlined in which the mowed grass will go to. this will help to avoid piles and crowding. In addition, at the end of work, it will be easier to clean.
  • Another very important point is to shield large weeds. For example, a formed bush of a burdock, which not every knife is able to cut. If such a large weed is found on your way, you should bake it in a circle and continue to work. When the work around the perimeter is completed, lonely sticking weeds will remain on the site, which are easy to remove with their hands, moreover, they are not mixed with grass.
  • The main thing in the span for hay is to leave the length of the grass, not allowing it to lose shape. Otherwise, the resulting mulch can only be used as covering material.
  • The width of the mowing should remain strictly fixed, t.to. It is necessary to remember the average size and length of the workpiece.

Some experts recommend using a fishing line for a trimmer when running for hay, but this is not always right. Firstly, usually the grass in such a section is high, moreover, its base is a more dense and formed. The use of fishing line will increase engine wear, as it will have to work at high speeds. Of course, this will affect performance. Secondly, a fishing line for a trimmer is simply not provided for such loads. Using this material, you risk not only the fishing line itself, but the whole mower.

The best option is a disk designed for shrubs. it is designed for increased loads. In addition, the high grass is rude at the base, and it will roll the blade most productively than a fishing line designed for soft, silky lawn grass.

There are additional devices for navigation by a trimmer for hay, but all of them are unofficial modifications. In other words, homemade improvements, the use of which is extremely not recommended, t.to. The behavior of the device in unexplored conditions can be unpredictable. Following simple recommendations, you can quickly gain the necessary experience and harvest hay in large volumes.

Spinning high grass

It is not difficult to cut high grass. The mowing occurs immediately in two directions. First to the left, then to the right (first passage), cutting off the top. Then in the opposite direction, but already lowering the bar with the blade to the necessary level. In this case, the grass, which was squinted, remains to lie on the left side, which is very convenient when the subsequent collection. It happens that the weeds grew too much and plentiful. In this case, several movements may be needed to the right and left, most importantly, adhere to the correct pattern.

With several movements of the fishing line for a trimmer, it is consumed much faster, but in some cases it may be necessary to get to the base of thickets into which it is impossible to cut through. If necessary, a fishing line for a trimmer can be alternated with a knife. If difficulties arise, and the productivity of the device has decreased, it will be enough to simply replace the consumer and start work again.

Do not try to pump high grass immediately under the base. this can lead to difficulties. For example, a long stem can be wound on a fishing line for a trimmer, which will lead to a long.term unplanned stop.

Important: when working with the blade, the speed of work may slow down a little, since its area is less than the scope of fishing line.

Safety regulations

Among the safest and most popular trimmers, the products of German manufacturers (including Denzel) are especially appreciated, as they pay increased attention to quality and reliability. However, despite the brand and model, there are a number of rules that, when using a trimmer for grass, you need to clearly know and observe.

  • Before use, you must familiarize yourself with the instruction manual.
  • You can not work with a trimmer in a state of fatigue, illness, intoxication.
  • It is forbidden to use a braid in explosive and fire hazardous areas.
  • You can not mow during a thunderstorm and rain, as well as after the rain, when the grass is wet.
  • You can only work in daylight hours, in conditions of good illumination.
  • Only the type of fuel and lubricant, which is suitable for a specific model of a trimmer for grass, should be used.
  • It is not recommended to independently repair the tool.
  • Do not touch rotating or heated elements during operation.
  • You can not smoke and make fire in the process of mowing and t.D.

Important! When operating a trimmer for grass, there are other factors harmful to health: increased noise, vibration, exhaust gases, high temperature of some parts, flying branches, etc. To minimize risks, you need to use overalls, glasses and headphones.

If there are questions about the adjustment on a rug belt of a particular model of motorcycles, the answers can be tried to find in the operating manual attached to the products, or watch a video on the Internet, where it is clearly and accessible how to set up and adjust the belt along with a gas station.

A trimmer casing for grass. how to choose yourself?

The casing plays the role of an element that reliably protects not only the legs, but also the hands and eyes of the operator

When choosing a casing, you need to pay attention to the following factors:

  • Material. it is best to give preference to casings made of high.quality and thermally processed multilayer plastic. They are stronger and much more resistant to blows and deformation;
  • the presence of stiffness ribs. so that the casing does not break in the first year of operation, on its rear, stiffener ribs should be provided. They will not allow plastic to crack or fly in different directions when hit;
  • The diameter of the landing hole is so that the casing is securely fixed in the lower part of the bar, it must be installed using a bolt connection. In this case, the diameter of the hole in the mount plays an important role. It is best that it is about 1 mm more than the diameter of the bar. In this case, the casing will not hang out in the lower part of the trimmer for the grass.

When choosing a casing, you also need to take into account its width. In practice, accessories have shown themselves optimal, the width of which is 30 cm. this is enough for reliable protection of the operator from stones and grass.

What is a rug belt

It should be understood that the weight of the seasoned motorcycles is an average of 6-9 kg. And this device must be kept in a limited state all the time. To evenly distribute the load, the backpack belt, as it were, encircles the body from all sides. The main load falls on the shoulders and back, so its upper part is complemented by wide foam inserts and tissue straps. Further belts are lowered along the body and with the help of a quick.sitting clip are connected to each other in the area of ​​the chest or abdomen. And so that when loading, the belt does not crash into the body, a wide and durable lining is provided. Plastic protection for the legs is attached to the belt. It has a carbine for attaching to a trimmer and depreciation in the form of a spring. The ease of unfastening and fastening the motorcycles is ensured by a rapidly latent latch located on top.

On a note! Different models of the paramedic belts can differ among themselves by the design of locks, carbines, the presence or absence of additional linings and latches. However, the principle of the device and operation is the same.

Fixing the lawn mower on the belt

Depending on the model, a gasoline braid can be mounted on a belt using a bar or loop. In the latter case, for balancing, you need to move it along the rod to get the necessary result. In some cases, depreciation mechanisms are provided, which allow you to smooth out vibration and soften the sharp surges of the trimmer for grass.

| Denial of responsibility | Contacts |RSS