How to lubricate the tire of the chainsaw tire?

You are the owner of the chainsaw recently, and you still do not know what oil for lubrication of the chain chain is better to use. Lack of this knowledge, can adversely affect the tool, t. To. How long the tire and the tool chain will maintain their performance depend on the type and quality of the lubricant.

After reading this article, you will make up a gap in knowledge, t.To. We will consider the issue of the use of oils, various manufacturers and brands, to reduce friction between the details of the saw headset. And also we will figure out what additional lubricants are used to serve the chainsaws in order to extend its operation as much as possible.

  • What oil to use to lubricate the chain chain
  • Lubrication for a star of chainsaw
  • Manufacturers of adhesive oils
  • Adhesive oils StiHL
  • Husqvarna oils
  • Other manufacturers
  • Expert comparison of oils
  • How to replace the original expensive oil and whether it is worth?
  • A little about the lubrication of the chain of the chainsaw

The device for lubrication of the chain of the chain of the chain

The components of the lubricant system of the chainsaw:

  • Oil tank (located in the crankcase, oil needs to be poured into it so that it comes to the chain);
  • Oil filter (installed inside the tank);
  • Oil pipeline or oil.Conducting hose (made of rubber resistant to wear);
  • Oil pump;
  • Gear of worm gear;
  • The tire of the chainsaw (it contains holes through which oil comes).

What oil to use to lubricate the chain chain?

For proper operation of the chainsaws, two types of oils are used. One for the preparation of the fuel mixture, and the second for lubrication of the chain. In this article we will consider the second type, namely what kind of oil to use to lubricate the chain. The use of unsuitable oil leads to premature wear of the saw tire and chain, so this issue should be taken seriously.

I immediately note that the oil is used for this task special, and it needs to be used precisely by it. I will explain below why. Also, many in this context are interested in whether other types of oils can be used, including working out from the car engine, and if not, then why. I will reveal this topic.

How the chain of chainsaw is lubricated?

To understand further information, it is desirable to understand how the chain is generally lubricated if you still do not know this.

Each modern chainsaw has an oil pump. The chain oil poured into a special tank for lubrication of the chain begins to swing this pump immediately after the factory and floods through the oil channel to the oil receiver on the tire. Through it, the oil enters the groove of the tire and spreads with a chain along the entire working length of the tire both at its top and the bottom.

The main load when sawing falls on the lower part of the tire, since it is it that is applied to the sawing material. However, the oil first enters the upper part of the tire, passes through its entire length, and then through the rounding at the end of the tire enters the lower part. Naturally, when passing such a turn, part of the oil simply flies out of the tire and chain due to inertia. Therefore, it is important that it flies as little as possible, so that the lower part of the tire is well lubricated and between the chain and the bus is as little friction as possible.

Therefore, knowing this information, we can conclude that the oil lubrication oil should be thick enough and have good adhesion (in other words, adherence) so that it will fly less on the tire rounding, and it should also not contain any particles so that it can be possible so that it can freely pass through the oil channel, without scoring it, and so that these particles do not create excess friction.

Special oils for lubricating the chain have all these properties. They are quite dense, have special adhesive additives in their composition, and naturally do not contain any particles. In addition, they form a kind of film between the chain and the bus, so that the chain with the bus in essence does not touch each other.

Among different manufacturers, the properties of these oils may differ slightly. Those that are more expensive, usually adhesion have more. But in any case, any specialized oil for lubrication of the chain will be better than any other designed for other purposes.

Now with such information you can answer questions about the use of other oils.

Is it possible to use motor oil for lubrication of the chain?

Motor oil in comparison with the special does not have the necessary adhesion, and also too liquid, so the lower part of the tire will be lubricated with it, which will lead to rapid wear and tire and chain. Therefore, this option needs to be abandoned.

Using a transmission oil chain for lubrication

This option will be of course better than using motor oil, since the transmission is simply thicker. However, it also does not have the necessary adhesion. Therefore, the lower part of the tire, although it will be lubricated somewhat better, is still not good enough.

Lubrication for lubrication of the chain

This option is the most disgusting. Working is essentially the same motor oil, but which contains microscopic metal particles that it absorbed when working in the engine. These particles can clog the oil channel, and they also clog between the links of the chain and the tire and chain itself, and work there as an abrasive, which is why the tire and chain simply abrasion, and the chains are even torn. Therefore, we also say “no”.

Well, now I hope you understand why the oil specially designed for this should be used to lubricate the chain. And if you are also worried about nature, you can use its special variety, which decomposes after use, since it is made not from oil, but from plant material.

This is all I wanted to say on this issue. Thank you for your attention and see you in other articles on the site.

See also  How to measure the length of the tire on the chainsaw

Oil for lubrication of the chain of chainsaws: what proportions, how to dilute and how much to pour

For owners of private houses and summer cottages, a chainsaw is an indispensable technique. With its help, you can quickly and easily perform various work. Cut firewood, construction of wooden structures and pruning of old trees. In order for such a technique to serve for a long time and it is necessary to correctly observe the rules of operation of the chainsaw.

One of these rules is the preparation of the fuel mixture for the chain. How to do this correctly and what kind of fuel should we try to find out in our article.

Oil for lubrication of chains of chainsaws

The chainsaw has two tanks, gasoline is poured into one of them, and in the other oil to lubricate the technique chain. The durability, the serviceability of the chainsaw will depend on the quality and composition of the oil, as well as the fuel. Often in technology stores, finished oil is offered from manufacturers of chainsaws, it is intended for such a purpose. The finished product is suitable for work at low temperatures and does not pollute the environment.

Finished oil can be replaced by others, the main thing is that it is not worked out. Representatives of manufacturers of equipment recommend buying branded oil or preparing a mixture based on the operating instructions. If the instructions do not have a specific type of oil, then you can buy a two.Stroke oil, which is sold in a specialized store. Two.Stroke oil can be of two types:

Experts advise using synthetic oil for chainsaws, but at a price it is always more expensive. The main advantage of this type of lubricant is that during the operation of equipment in the cylinder does not form soot, and this extends the life of the equipment.

lubricate, chain, chainsaw, lubricating

If mineral oil has been used for 100 working hours, then it is better to continue to use it, because in the process of work it could accumulate. The synthetic product has the ability to clean and remove the deferred layer from the cylinder walls, and this will lead to damage to the technique.

How to make a mixture for lubrication of a chain correctly

If we use the “native” oil for the chainsaw, then the desired proportion is indicated on the package, usually 1:50 to gasoline. When another product is used, then it is better to dilute the mixture of 1:40, in other words, it is necessary to divide 1 liter of oil into 40 and add the result to add 1 liter of gasoline.

For self-preparation of the mixture, you need to use gasoline A-92 and A-95, if the octane number is lower, then this can lead to engine breakdown. If gasoline has stood in a canister or other container for a long time, it is already considered unimportant and loses its properties. Poor fuel chainsaws will not be able to work powerfully and efficiently.

Experts advise choosing most chainsaws that are used in our regions with API-TB and API-TC class designed for two-stroke engines. Do not save on ingredients, but buy high.Quality oils from well.Known manufacturers and accurately observe the proportions for the preparation of the mixture.

If you add more oil to the mixture, this will lead to the formation of a carbon felted in candles and pistons. Excess gasoline will contribute to the appearance of bully on the pistons and the rapid failure of the chainsaw engine. Before preparing the mixture, you need to carefully read the instructions on this model of the technique.

Ready.Made mixtures are not recommended for a long time, a maximum of 1 month, you can not save it in open form or in the sun. The water or dust that enters the mixture can lead to a carburetor breakdown, since the installed filter cannot completely clean the fuel.

Fuel mixture capacity

Before starting the creation of fuel, the question arises. What to mix the proportions of oil and gasoline? Specialized stores have canists with measuring divisions, as well as two holes. They need to separately pour gasoline and oil in them, then tighten the lids and mix everything thoroughly, tilting the canister.

You can use simpler containers that are always at hand, for example, plastic bottles or glass, but statistical electricity occurs in such objects. Be sure to make sure that dust or moisture, solid particles do not get into the container, if all the proportions are observed, then you need to mix everything well.

Когда смесь окончательно готова, ее можно залить в бак, аккуратно не развивая топливо и так, чтобы он был заполнен не до конца. Depending on the use of the chainsaws, it is necessary to either fully use the entire lubricant or drain it into the container and then pour it again as necessary, but no later than 30 days later.

It is good to use various additives recommended by manufacturers of equipment so that fuel is better. A lot is sold on the sale of additives and you can choose the right for your chainsaw.

The operation of the chain lubrication system, types of oils

It is necessary to periodically check the oil level in the tank and the operation of the lubricant system. If you look at the rotating chain with the illuminated surface, then in the presence of oil spray the system works normally and is correctly configured. If the cutting headset quickly heats up, then this indicates a minimum level of lubricant in the chain, so it can get pinched during operation.

There are a lot of types of oils, they can be different in price, environmentally friendly, sold in different capacities in volume. You can consider several options for products.

  • Budget option. Nanothek standard, you can work with it at temperatures before.20OS, premium nanothek to.30OS. Also, this category includes a product from Encor, with a capacity of 1 liter.
  • Mineral oils with bio console. Makita Biotop, Stihl Bio Plus.
  • Oils recommended by the manufacturers of chainsaws. Makita Biotop, Makita, Oregon.
  • In large volumes containers-Encor oil 3-5 liters, Stihl 5 liters, Oregon 5 and 25 liters.

The main task of creating a mixture for lubricating the chain is the uninterrupted operation of the engine, the complete combustion of fuel, so that in the end smoke, soot or bully can not form. Compliance with the necessary proportions, proper operation and high.Quality ingredients will help to use a chainsaw for various business works as long as possible.

Expert comparison of oils

In order to understand what users choose for lubricating the chains of their chainsaws, we analyzed the statistics of the Yandex marketplace.The market and selected the most popular (sold) oils, studied reviews, compared them with and compiled a comparative table by which you can determine which oil should be chosen.

As a result of comparative tests, 3 winners were determined:

  • Caliber. Cheap, good adhesion, biodegradability.
  • Oregon. Average price, good adhesion, brand time.Tested.
  • STIHL. Expensive, brand time.Tested, affordable price, many fakes.

Here everyone chooses that he is closer to his liking and the possibility of biodegradability or price. The choice of editors. Oregon. This is a golden mean between quality and price.

Electric Chainsaw Maintenance, Cleaning, Lubrication How To

lubricate, chain, chainsaw, lubricating

Checking the system for oil output and performance

Oil filter pollution is manifested by a significant decrease in the performance of the pump. Check this parameter is easy. To do this, it is necessary to hold a headset at the work of the saw on a clean sheet of paper.

See also  STIHL or Husqvarna chainsaw what is better

By the density and size of the oil strip, one can confidently judge the state of the system and the complexity of the upcoming repair.

When asked why the renovated lubrication system works, but does not go to the chain in the right amount. There is no unequivocal answer. The cause of failure may be error, failure of standard adjustments, mismatch of the density and viscosity of the selected composition by the declared characteristics.

Mastery starvation of the headset is possible when installing on a household saw with an unregulated pump of a longer productive tire, which is equipped with a professional class chain technique.

How to lubricate the tire of the chainsaw tire

In this article, we have collected recommendations for the professional maintenance of saw systems. Setting up, lubricating and replacing chains, tires and stars. Try to follow them, and then your work will always be done on time and at a worthy master level.

At the usual load, the leading star wears out twice as slowly than the saw chain, so for uniform wear of the saw, it is recommended to use two chains alternately. This is also advisable because the leading links earlier will become unusable if they are in contact when rotating with a worn leading star. We advise you to remember a simple rule: 4 chains = 2 stars = 1 tire.

IMPORTANT! It is not allowed to install a chain on a worn stars or tire.

Of course, with the question of which chains for chainsaws are better and how to choose the most suitable, you should contact our interactive consultant, indicating the manufacturer and model of your saw.

Clusion of the chain of the chain of the chain

It is important to carefully monitor the tension of the saw chain and, as necessary, pull it up. Its sagging on the tire is categorically excluded. Weak tension enhances components wear, increases the load on the housing and can cause shock absorbers breakdown.

In addition, before replacing the chain of the chainsaw with a new one, you must first withstand it one night in an oil bath so that all its components are properly lubricated. Otherwise, its premature stretching is possible.

IMPORTANT! Before adjustment, let the working part cool. After the sawing is completed, the tension should weaken.

Service and lubrication of the guide tire

lubricate, chain, chainsaw, lubricating

In order for the tire to serve as long as possible, it is necessary to periodically turn it over and replace the worn saw chains in time. If burrs appeared on the upper faces of the tire, then at the end of the work they need to be stuck with a flat file. It is also necessary to clean the grooves and openings of the lubricant after completion of the work.

Follow the quality of the poured fuel mixture!

The fuel mixture of gasoline with an octane number of at least 92 with butter for a two.Stroke air cooling engine in the proportion indicated by the engine manufacturer is recommended. There is a wide range of oils for chainsaws: semi.Synthetic, blessing, anti.Corrosion. They protect the candle from the appearance on its surface, which is extremely important for comfortable work with a chainsaw.

Adjustment of the drain depth limiter

There is an opinion that a cut limiter can be cut off so that a cutting tooth can take more wood, increasing the speed of sawing. It’s a delusion. Such a modification causes premature wear of the working headset and, even more importantly, over time leads to a canvas for a saw due to increased load on the motor unit.

In order for sawing in the cold to flow smoothly and is not accompanied by excessively rapid wear of cutting links, we recommend reducing their sharpening angle by 5 ° or 10 ° C of the usual 30 °.

Chain saw oil leak problem/oil pump replacement #sinhala #තෙල් කාන්දු වීම #MB tec

Sawing of frozen wood (for example, when logging in the winter, working on a personal plot or the performance of certain tasks of the communal economy) is fraught with premature wear of the saw system and metal breaks around the axial holes of the cutting links. To avoid this, it is enough to dilute the lubricating oil used by diesel fuel or kerosene without impurities by 25%.

The return return is one of the most common causes of heavy injuries when working with motor saws. It occurs either when the tire nose is contacted with the object, or when the saw chain is clamped in the cut. In the first case, the tire can sharply bounce up the arc to the operator, and in the second. In a straight line to it. In both situations, control over the saw can be lost, which can cause serious injuries to both the employee himself and nearby people.

The top of the tip of the saw tire is known as a dangerous retreat zone.

Modern saws are equipped with a number of protective mechanisms, the purpose of which is to reduce the threat of injury from the reverse return to a minimum. This is a circuit brake, straight (left) manual protection, protection of the tip of the tire, as well as a device for reducing reverse return on saw chains and guide tires. It is important to understand that for the proper functioning of all protective systems and mechanisms, your saw must be entirely assembled and configured according to the instructions, it should not be poorly fixed and strongly worn components.

OREGON advises always to use low.Back in feedback chains and switch to ordinary ones only as necessary and only if you have sufficient experience. Before starting the operation of any chainsaw, be sure to carefully read the instructions of the manufacturer for work and safety precautions.

I want to use TAD 17 on the TAD 17 chain on the Stihl 250 chain. In winter it is very thick. Will it not be worse from this to the oil pump, will it fail from overload? And if possible. What kind of principle is there, in the pump, oil supply to the chain?

The oil pump, which is placed at 180. 250, was generally unbearable. It has a brass cylinder. Even earnings are eating two times longer than aluminum.

And the principle of action is very simple. It’s a pity, there is no illustration, and I have never seen anywhere. If in words. Two details, a cylinder and a plunger rotating in it. The plunger has a milling gun on the end. When rotating, the plunger moves slightly forward and forth.

Two holes are made in the cylinder against each other. When the plunger’s bald approaches the fence hole, it is slightly stretched out of the cylinder. A vacuum is created and a little oil is absorbed.

When the bald rotates to the discharge opening, the plunger moves into the cylinder. The pressure is created, the oil goes along the channel to the tire. As you can see, in principle, it is impossible to damage the pump as long as thick oil. It simply will not go, and everything. _

If the oil flows from the tank in the inaction of the chainsaw. This is normal? T.E. If you have to saw a little, then pour a little bit? Otherwise during the inaction of the saw, the oil from the tank flows completely.

Not. This not normal. The problem is either with an oil pump, or with the tank itself. In general, the consumption of oil and fuel, usually 1 to 1. _

Leading star tire on a chainsaw than to lubricate? Whether, for example, a lubricant for hydraulics mobil or JCB is suitable? What do you think?

See also  How to disassemble a chauter chainsaw. How to disassemble a chausopila Husqvarna

How to lubricate a chainsaw

If you are a new owner of a chainsaw, then you are probably starting to get used to your new car. But in order for your saw to work uninterruptedly, you need to provide general maintenance, and one of the most important details, which should be constantly remembered, is the level of oil in the tire and chain. It differs from the oil that you mix with gas for lubrication of the engine, and below I will describe the importance of this task and explain how to lubricate the chainsaw both for safety and for caring for it.

How a chainsaw works

Chainsaw is driven by an electric or two.Stroke gas engine. This engine drives the gear and rotates it. The end of the chain of the chainsaw is put on one end of the toothache and installed along a strong tire. When the toothed wheel rotates, it rotates the chain around the tire, creating a powerful cutting tool.

The importance of oil and chains oil

The chain can move at a speed of up to 60 miles per hour, which means that it rotates at a speed of about 88 feet per second along the asterisk and tire.This creates a lot of friction, which must be lubricated to avoid overheating and seizing. The oil allows you to smoothly move the metal through the metal without overheating.

A saw that works slowly, feels or smells of “hot”, or pumps the gas faster than it should. All this indicates that the chain rotates not as it should. This can lead to overheating of the engine, as he tries to work against friction created by the chain when it moves along the star and tire.

Type of oil used

Oil for the saw tire and chain is specially designed so as to be viscous enough to withstand high friction caused by the chain. Most saws are supplied with a test bottle of oil and offers about which oil to use, but for the most part the oil is one and the same from the same brand to another.

In extreme cases, you can definitely use alternatives. You can use ordinary vegetable oil, and it is surprisingly effective. However, he does not work well in very hot or cold working conditions.It is better to leave this when you work in areas where there may be restrictions on gasoline in environmental conditions.

It is better to avoid using any type of motor oil due to improper viscosity. Again, if it is absolutely necessary, you can use it as a last resort, but select oil weighing 30 and make sure that it is clean to avoid garbage in the tire groove.

How self.Piles work

Almost all saws are self.Sinking, which means that they have a reservoir designed to supply oil to the tire and circuit while driving. The oil is pumped out with the same crankshaft, which is driven by the engine, which drives the chain. Then the oil moves along a small channel to a small hole in the guide tire, to the groove of the tire in which the chain is located. When rotating, the chain lubricates the entire groove.

What you need

  • Oil for the tire and chain is always useful to have at hand due to how much you use regularly.
  • Gloves. Help protect your hands from oil, dirt and soot.
  • Funnel. Avoid spills and make sure that the oil gets to where it should be, without failures.
  • The towels for the store are indispensable for working with power tools and a chainsaw to help remove any spills, as well as wipe clean surfaces.

Location of the tank with oil

Most oil tanks are very easy to find, they can be found on the oil cover on the main saw building. Many reservoirs are also transparent, which allows you to see the level of oil. If you are not sure of the whereabouts, be sure to contact the user management.

Back gas station

Before opening the reservoir, be sure to clean the lid and the surrounding area from any oil residues and dirt.You do not want any particles to get into the tank, as they can get into the tire grooves, worry on the chain and create an unsafe situation. With a firm hand or with the help of a funnel, pour the oil into the tank either to the marked line (if it is obvious), or until the tank is filled.

When to replenish the score

Designed for oil supply during operation, so most tanks are large enough to accommodate enough oil for a full gas tank. Always check the oil level before starting the saw and during long work.You do not want the oil to end, as described above, you can damage not only the tire and chain, but also the engine.

Sprockets with a spout

The lubrication of the sprocket at the end of the saw canvas is intended only for some of the largest and most powerful saws equipped with this specialized canvas. These tires, designed for longer circuits and durable professional machines, have a number of stars on the end of the tire that help direct the chain. If you have a saw on which this type of bar is used, you will also need a lubricant syringe, which will also shoot there a few spray.

Although, probably, this is one of the most important steps for maintenance, which you need to take care of, lubricate the chainsaw and the easiest way. Almost every saw has a self.Smelling reservoir, which simply requires you to keep it clean and fill it with each gas tank or as necessary. Be sure to follow these levels so that your chain moves smoothly and the engine does not overload.

The oil does not enter the chain, what are the reasons

It is not always possible to immediately see that the oil is not supplied to the chain of the chainship. Signs of lack of lubrication:

  • The level in the tank does not decrease;
  • The cut goes with difficulty, accompanied by the smell of a burning tree;
  • Oil droplets do not fly off the tip of the tire of the chainsaw.

Having discovered a malfunction of the oil system, it is necessary to establish its cause. There are few of them. Clogs, a break of the hose or a malfunction of the oil pump.

Most often clogged with dirt and sawdust channel oil drodics. Air purge or cleaning with thin wire is enough to eliminate the malfunction. The oil tank has its own internal filter. When using normal oil, its clogging is unlikely, and when pouring it, it is quite possible. We’ll have to clean.

It may be damaged or the oil hose is completely cut off. You can temporarily seer the damaged place, but it will be more reliable to replace with a new.

And the most serious problem is the breakdown of the oil pump. The reasons can be different. The teeth of the worm gear have worn out, the plunger and others were jammed. Removing the pump and replacing the damaged part yourself will not be easy. Reliable and easier to contact the service center.

| Denial of responsibility | Contacts |RSS