How to wind a fishing line for a trimmer for a lawn mower

Fishing lines is called consumable, which consists of nylon, and serves as a cutting device. Through this equipment, the grass grows, which is ensured due to rotation of the instrument head with a high frequency. This material has a different thickness, which depends on its use on the corresponding tools of low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers for grass with motorcycles (from 2.4 up to 3.2 mm).

The more powerful the tool, the accordingly there should be a cutting equipment. This affects not only the quality of the injection of grass, but also on the life of the material. If you ask the question of how to wind the coil of a trimmer for grass, then it’s time to change the reload of the tool. With the onset of spring, this issue is becoming more and more in demand, so it’s time to understand the step.By.Step instructions for replacing the fishing line in the coil of the trimmer for grass.

How to wind a fishing line for a trimmer for a lawn mower

To implement this method, you will need to pre.Prepare a fishing line for a trimmer of the required length (usually up to 4 meters). It all depends on the thickness of the equipment used, as well as the design of the coil. There is a simple way to find out the required amount of fishing line, the refueling of which will be needed to charge the coil. To do this, the equipment should be wound inside the coil until it is equal to lateral protrusions. At the same time, the equipment should not go out for these extreme ledges.

The thicker the equipment used, the less its length will need and vice versa, the thinner, the longer the segment will need.

Instructions on how to properly tie the equipment into a tip of a trimmer for grass or motorcycles is the following look:

  • To begin with, a segment of the fishing line, which was prepared to install in a coil, must be folded in half. In this case, one edge should be more than the second by 10-15 cm
  • After that, the second end is taken from the other side, and doubles. Move to it so that the measured ledge 15 cm is preserved
  • There is a slot in the internal partition of the coil, into which the resulting loop should be brought. The slot in the wall is shown in the photo below
  • Next, find out the direction of the winding of the fishing line. If you wrap the equipment in the wrong way, then it will not function correctly, and you will need to redo the work. To insert a fishing line for a trimmer, and wind it in the right direction, you should examine the surface of the coil. It should indicate the direction of winding (in 99% of cases this direction is indicated). What does the direction indicator look like on the coil shown in the photo below
  • This indicator in the form of an arrow can also have a designation, as an example above “Wind Line”, which means the direction of winding. If the arrow indicator is absent on the coil, then you need to look at the head. There is a direction of its rotation on the head, and in order to correctly wind the fishing line for the trimmer, you should wind it on the drum in the opposite direction of the indicator of the arrow pointer. So, if the shooter is on the tip, then you need to wind in the indicated direction, and if it is not there, then you should wind against the direction of the arrow on the surface of the head
  • Having decided on the direction of rotation, you should proceed to the winding. Each end should be carried out in its groove. If there is no separator, then the equipment is necessary in the corresponding distribution order
  • When almost the entire fishing line for the trimmer is wound on the coil, you will need to perform the following-place a short part in the hole of the side wall of the tip, which should be up to 10-15 cm, and then similarly to do the procedure with another end, placing it in the holes from the parallel side
  • We insert the coil into the head, pre.Letting the ends of the fishing line into the holes of the drum
  • We install the drum in place and, pulling the ends of the fishing line, remove them from the engagement with temporary clamps in the coil wall. After that, you can put on the lid until the latch is triggered
  • On this, the process, how to replace a fishing line for a trimmer on a trimmer, is completed, and if necessary, only the ends can be cut (if their length does not suit), and install the drum in the assembled form on the tool

fishing, line, trimmer, lawn, mower

With how to put the drum in place, no difficulties arise. There is a second way to charge mowing equipment into a motorcycle. How is it different, and how the second method of refueling the fishing line to the coil of motorcycles is carried out, we will find out in detail.

Reliable trimmers for grass grass in 2019

Since the choice of a trimmer for the grass we saw in the previous article, now we will tell how to correctly refuel a trimmer for the grass with a fishing line, and which is better to choose based on the criterion of work.

Black and Decker Mower Deck 2

After you purchased a trimmer for the grass and began to use it intensively, at some point the question will arise about the substitution of the fishing line, since this is the most weary element in the tool, the rich operation of the trimmer for the grass will often lead to substitution of consumables.

What you need to know about the fishing line on the trimmer for the grass

Fishing lines is called consumable, which consists of nylon, and serves as a cutting device. Through this equipment, the grass grows, which is ensured due to rotation of the instrument head with a high frequency. This material has a different thickness, which depends on its use on the corresponding tools of low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers for grass with motorcycles (from 2.4 up to 3.2 mm).

The more powerful the tool, the accordingly there should be a cutting equipment. This affects not only the quality of the injection of grass, but also on the life of the material. If you ask the question of how to wind the coil of a trimmer for grass, then it’s time to change the reload of the tool. With the onset of spring, this issue is becoming more and more in demand, so it’s time to understand the step.By.Step instructions for replacing the fishing line in the coil of the trimmer for grass.

How to wind a fishing line for a trimmer for a lawn mower

To implement this method, you will need to pre.Prepare a fishing line for a trimmer of the required length (usually up to 4 meters). It all depends on the thickness of the equipment used, as well as the design of the coil. There is a simple way to find out the required amount of fishing line, the refueling of which will be needed to charge the coil. To do this, the equipment should be wound inside the coil until it is equal to lateral protrusions. At the same time, the equipment should not go out for these extreme ledges.

The thicker the equipment used, the less its length will need and vice versa, the thinner, the longer the segment will need.

Instructions on how to properly tie the equipment into a tip of a trimmer for grass or motorcycles is the following look:

  • To begin with, a segment of the fishing line, which was prepared to install in a coil, must be folded in half. In this case, one edge should be more than the second by 10-15 cm
  • After that, the second end is taken from the other side, and doubles. Move to it so that the measured ledge 15 cm is preserved
  • There is a slot in the internal partition of the coil, into which the resulting loop should be brought. The slot in the wall is shown in the photo below
  • Next, find out the direction of the winding of the fishing line. If you wrap the equipment in the wrong way, then it will not function correctly, and you will need to redo the work. To insert a fishing line for a trimmer, and wind it in the right direction, you should examine the surface of the coil. It should indicate the direction of winding (in 99% of cases this direction is indicated). What does the direction indicator look like on the coil shown in the photo below
  • This indicator in the form of an arrow can also have a designation, as an example above “Wind Line”, which means the direction of winding. If the arrow indicator is absent on the coil, then you need to look at the head. There is a direction of its rotation on the head, and in order to correctly wind the fishing line for the trimmer, you should wind it on the drum in the opposite direction of the indicator of the arrow pointer. So, if the shooter is on the tip, then you need to wind in the indicated direction, and if it is not there, then you should wind against the direction of the arrow on the surface of the head
  • Having decided on the direction of rotation, you should proceed to the winding. Each end should be carried out in its groove. If there is no separator, then the equipment is necessary in the corresponding distribution order
  • When almost the entire fishing line for the trimmer is wound on the coil, you will need to perform the following-place a short part in the hole of the side wall of the tip, which should be up to 10-15 cm, and then similarly to do the procedure with another end, placing it in the holes from the parallel side
  • We insert the coil into the head, pre.Letting the ends of the fishing line into the holes of the drum
  • We install the drum in place and, pulling the ends of the fishing line, remove them from the engagement with temporary clamps in the coil wall. After that, you can put on the lid until the latch is triggered
  • On this, the process, how to replace a fishing line for a trimmer on a trimmer, is completed, and if necessary, only the ends can be cut (if their length does not suit), and install the drum in the assembled form on the tool

fishing, line, trimmer, lawn, mower

With how to put the drum in place, no difficulties arise. There is a second way to charge mowing equipment into a motorcycle. How is it different, and how the second method of refueling the fishing line to the coil of motorcycles is carried out, we will find out in detail.

Reliable trimmers for grass grass in 2019

Since the choice of a trimmer for the grass we saw in the previous article, now we will tell how to correctly refuel a trimmer for the grass with a fishing line, and which is better to choose based on the criterion of work.

After you purchased a trimmer for the grass and began to use it intensively, at some point the question will arise about the substitution of the fishing line, since this is the most weary element in the tool, the rich operation of the trimmer for the grass will often lead to substitution of consumables.

How to change a fishing line for a trimmer to a disk on a disk

Buy to the cottage | Ideas | Tips | Secret to choose a lawn mower?

Household and professional gasoline trimmers for grass every year are becoming more and more popular due to their high performance and mobility. Unlike their electric counterparts, they are not attached to the power source and are able to process large territories in area.

If you decide to purchase a trimmer for the grass, then most likely faced the problem of choosing. A wide range of these devices is presented in the garden technique market, to navigate in which it is difficult for unprofessional. In this article we will tell you how to choose the right lawnical mower.

As experienced gardeners advise, it is necessary to choose a lawn mower taking into account the volume of upcoming work, such as plants on the lawn and the features of maintenance of these tools. This is influenced by the following parameters:

Type of cutting mechanism.Before choosing a lawn mower, decide for what purposes you will use it. A tool equipped only with fishing line is suitable for cutting soft grass on the lawn.However, often gardeners have to deal with dry or tough grass. In this case, pay attention to the devices where the fishing line for the trimmer can be replaced with a cutting knife.Some models have the ability to install a shift disk. It will help to cope with branches and fine shoots in the garden.It should be remembered that all cutting mechanisms are consumables. They often have to change them during the season. When choosing a lawn mower, check whether it is easy to install a knife and fishing line.

The power of the tool.The time and intensity of work depends on this parameter. Before you choose a lawners for a summer residence, evaluate the upcoming volume of work. Do not buy a powerful unit with a spacious tank for a small lawn mowing. It should also be noted that the more powerful the engine, the greater the weight of the device. The optimal power of the trimmer for grass is 600-900 watts.

Engine’s type.All gasoline models can be divided into two types: two.Stroke and four.Stroke. The former are most common. For refueling, it is necessary to prepare a special mixture of gasoline and engine oil.In a four.Stroke engine, fuel is poured directly into the tank. The oil is in a special container. Crankcase. Such models are more reliable and produce less noise. But at the same time they are more expensive and harder. What type of lawn mower will be easier to operate, easier to maintain and better cope with the work of the site on your site-experienced specialists of our online store will be told.

The shape of the bar. Curved. Twisting from the engine to the cutting mechanism in such a trimmer is transmitted using a steel cable located inside the bar. Such tools have less power, but they are easier in weight. Straight. If productivity is important, it is better to choose a direct shape of the bar. It can be whole and collapsible. If you plan to often transport the device, stop on the second option.

The shape of the handle.When choosing a lawn mower, it is worth paying attention to the shape of the handle. They are t-, d- and j-shaped. The latter are used for mowing high grass. They are the safest. The operator holds the device at a great distance. Devices with a D-shaped pen have greater maneuverability. To process open areas, a tool with a T-shaped handle shape is used.

So, let’s summarize. When choosing which lawmaker to buy, answer the questions:

What cutting mechanism. A fishing line for a trimmer or a knife. Will be required to process your site? What power level needs? The curved or direct shape of the trimmer bar for the grass will be more comfortable when operating and storing the tool?

If you find it difficult to answer these questions and choose the right garden equipment, contact the consultants of our online store.

You can get a consultation by phone: River Station 7 (495) 221-21-08-Western 7 (495) 228-09-51

How to apply for ownership of a garden house

Lawn mowing battery Bosch Rotak-32 Li-Ion 36 in 4 AH reviews

Planting tomatoes for seedlings in 2019 according to the lunar calendar in the Moscow Region

I can’t participate in the discussion now. No free time. I’ll be back. I will definitely express my opinion on this issue.

Of course, I apologize, but this answer does not suit me. Maybe there are still options?

How to refuel a fishing line for a trimmer to a trimmer coil for grass? Video instruction

Warranty production of the factory refueling of a trimmer for grass will inevitably require replacement of fishing line. Having a very approximate idea of ​​how to fill the fishing line for a trimmer to the coil of the trimmer for the grass on their own, beginners are reluctant to take this matter. However, with some skills, the development of this simple science does not represent any difficulties, and the presented instruction below will facilitate this process as much as possible.

Assembling a weed eater line spool rack with Cutter!!!

How to wind a fishing line for a trim for a lawn mower

Winding a new cord on a reel. A rather easy process. For work, a skein of a new fishing line of the desired diameter and shape, a knife for cutting and protective gloves will come in handy for you. The following is the scheme for replacing the fishing line with a reel with 2 antennae, as this is the most common version.

  • Cut the fishing line for a trimmer 2-4 m long (the length of the segment depends on the thickness of the cord and the tips of the manufacturer). Do not use the cord of the larger length, since it will rotate and stretch worse when running.
  • Remove the trimmer head from mounting (each model has a different method of fastening-special latches or a barashka nut) and disassemble it. Gently spread all the details nearby, losing nothing.
  • Wind a fishing line for a trimmer to a reel. There are 2 types of coils: with a dividing side and without it.

Sprout

  • Fold the fishing line for the trimmer in half and put on the bending place on a special groove in the coil. If it is not, simply cut the cord into 2 parts along the fold line and fix the ends in the holders.
  • Pass the tips in special gutters on each part of the coil.
  • Start wrapping the remaining length of the cord in one direction.
  • Leave 20 cm at the ends and place them in opposite directions, stretching into special holes.
  • Cord the cord of the desired length in half.
  • Fix the tips in a coil in special mounts or drive into the holes.
  • On the bobbin indicates the direction of winding, in which direction you need to wind the cord. Wind up, not allowing segments to cross the coil.
  • Dilute the ends on the opposite sides and insert into special slots. The diameter must match.

Important! Buy a corporate cord, which is recommended for your lawn mowing model. It is stronger than cheap analogues and will serve longer. Also pay attention to the diameter of the holes in the coils with a dividing side to choose a fishing line for a trimmer of a suitable section. Do not wrap the fishing line for the trimmer tightly, provide it with free move during work.

fishing, line, trimmer, lawn, mower

To wind a fishing line for a trimmer to a coil with 1 cutting end, you should not fold the cord, and for mowing heads with 4 antennae, you should prepare 4 pieces of fishing line. Winding scheme is the same as described above.

| Denial of responsibility | Contacts |RSS