School for a walk.Behind tractor what is it and how to install how to set up and adjust your sonnik with your own hands

Beginning farmers often face problems caused by the improper operation of the cultivator. Often, the motor.Cultivator is instilled into the ground, and does not lend itself to any manipulation of the operator. To solve this problem, first of all, you should deal with the reasons for its appearance.

If the cultivator buries with plowing, then this is due to several reasons.

  • This is often due to the equipment of the technique. Most often, mini-cultivators are equipped with four mills. Provided that the manufacturer of high.Quality metal is used for their manufacture, they will have a large weight. Because of this, working elements will pull the cultivator into the soil;
  • Sharp knives of the milling cutter. If the cutting elements are sharpened, then the cultivator will not move forward, but on the contrary, it will burst into the ground;
  • Strong load on the engine. In this case, the motor will create strong vibrations, which will violate the balance. Because of this, the cultivator will delve into the ground in place, instead of moving around the garden;
  • The second common reason is the untimely switching of the cultivator to the second speed. This cannot be done with plowing loose soil and under its high humidity;
  • The cultivator is often instilled in connection with incorrectly installed mills. If for their attachment to the coupling mechanism to choose a angle more than this requires a guide to use, then this will also cause the equipment to dig.

Very often, the technique buries into the ground due to too zealous shocks from the operator. The owner must remember that only slight push of the equipment in the right direction is required from him. If you make too much effort, this will violate the balance of the cultivator, and it will fade into the soil all the time.

If the cultivator buried in the soil, the operator should take a number of measures.

  • Dismantle the extreme cutting knives from the milling cutter. This will reduce the mass of equipment. Another way is to improve the balance of technology by installing any small load in its rear. It is very important to fix the counterweight motionlessly, otherwise it will fall under the influence of engine vibration;
  • To quickly pull out the equipment out of the soil, you should switch the cultivator to the rear mode mode. If it is not provided in the design, then the equipment will have to be pulled out of the ground on their own;
  • When working, the operator must correctly adjust the position of the milling. Their cutting knives should always be directed right in the direction of the movement of technology.

To exclude the burden of the cultivator, you need to carefully inspect the transmission before work. This mechanism should be completely serviceable. You can not use the cultivator if the speeds are arbitrarily switched on it.

If the farmer noticed this breakdown, then it will be necessary to inspect the gears of the transmission. Self.Switching of speeds indicates the collapse of the gears of other nodes. To eliminate the breakdown, you will need to adjust the distance between the channels and the gears of the transmission.

To exclude the risk of digging the cultivator into the ground, the farmer needs to adhere to the list of certain rules.

  • Do not rush with soil processing immediately after precipitation. The technique will quickly immerse yourself in too soft wet soil. In addition, the high soil moisture will lead to the formation of rust on cutters and other metal elements of the cultivator;
  • Correctly set up a couch before each use of a cultivator;
  • Install the gas control regulator into the maximum allowable value and always check the switching mechanism;
  • Cultivate the soil at least twice. During the first processing, the couch should be installed in the minimum deepening position. The second processing should be performed with a coupon installed on the depth required by the farmer required.

When using the cultivator, it must be remembered that thorough checking and setting up equipment are the main methods that will help to exclude the burden of equipment.

In order to exclude the burden of the cultivator and a number of other common problems, the owner of the equipment must perform a number of actions to prepare and configure it.

  • First, the cultivator must be installed on a thick board and remove the factory wheels from it. Instead, you need to fix one set of mills on the left and right side. 8 cutting knives include one set of cutting. This number of elements gives the best result when treating soil;
  • When installing milling, you need to pay attention to the position of the knives. They should be directed only forward. The working part of each of the knives should not be acute. Otherwise, the cultivator will not move forward, but will begin to explode into the ground. In addition, sharp mills will cut off the stalks of weeds, and not wrap and pull them out with the roots;
  • Further, the equipment will need to be installed in the earring necessary for the installation of a coupon;
  • Sushnik is a bar with holes made in it. It is necessary to accurately adjust the position of the milling cutter during the cultivation of the site;
  • To fix the council, it must be installed in earring and fixed with cords and bushings. For this, the second hole is selected. The countdown is carried out from the lower part of the council. Thus, the depth of cultivation will be 20 cm. This is enough for high.Quality soil processing and eliminating large weeds;
  • To increase the depth of cultivation, the couch must be lowered down, and attached to the earlier through the upper hole of the element;
  • To reduce the depth of plowing, the couch should be lifted up, and fixed on the earring through its lower hole.
See also  How the tape grinding machine works. Fire replacement in 5 movements

By installing and setting up the working equipment, you can begin the operation of the cultivator. To accurately determine the depth of plowing, it is necessary to make a control project of equipment in the site.

At this time, you need to pay attention to the work of the cultivator. If its engine vibrates and smokes strongly, then the technique is excessive loads.

Read more: designer tables 41 photos Features of choosing original furniture from plywood and other materials of the model of white tables with chairs on a metal frame in the interior of the living room

Home made tractor.

How to set depth on the cultivator?

To establish the desired depth of processing, under the wheels, the gasket should be installed with a thickness, which will be equal to the future depth of the earth, reduced by a size equal to drowning the wheels (usually approximately 25 mm).

If you raise a snuffshold, then the car will run on the cutters forward, as on wheels. Therefore, it is necessary to work like this: I pressed the handles down, stopped the cultivator, waited a little when it loosen the entire volume around the milling rods Then I lifted the handles up, freed the couch, the car crawled a little forward.

How to work properly a cultivator in the garden?

The cultivator must move smoothly and evenly. If it buries into the ground, then it is necessary to adjust the position of the wheels or change the mills in places. After using the unit, wipe all its metal parts with a rag. If necessary, rinse the mills followed by wiping dry.

For plowing land in the Moscow region

Plowing services. Izm.Price per hundred
Land of the Earth with a motorcycle unit (large fraction) a hundred 1800
Land of land with a tractor (large fraction) a hundred 4000
The virgin soil plowed up a hundred 2500
Trinker plowing with a tractor a hundred 5500

How to work properly a cultivator in the garden?

The cultivator must move smoothly and evenly. If it buries into the ground, then it is necessary to adjust the position of the wheels or change the mills in places. After using the unit, wipe all its metal parts with a rag. If necessary, rinse the mills followed by wiping dry.

When installing a coupon in the holder, you need to fix it through a particular hole using the cobble. The choice of the hole depends on the depth of the earth you need. If you want to install the minimum depth, then you should install the couch on the holder through the lower hole.

How to put a sashnik?

When installing a coupon in the holder, you need to fix it through a particular hole using the cobble. The choice of the hole depends on the depth of the earth you need. If you want to install the minimum depth, then you should install the couch on the holder through the lower hole.

When installing a coupon in the holder, you need to fix it through a particular hole using the cobble. The choice of the hole depends on the depth of the earth you need. If you want to install the minimum depth, then you should install the couch on the holder through the lower hole.

Do.It.Yourself manufacture

Bunker capacity should be made of plastic. It is easier to visually control the number of seeds poured. Take the following components:

  • A bolt that will be used as an axis where the container filled with seeds will rotate.
  • A plastic pipe equal in its length sizes (in the depth) of the bunker. Steel pipe is the same length.
  • Aluminum wire.
  • Pipe mounting pucks.

The assembly is a phased process. We describe the algorithm:

  • In the center of the selected plastic jar, it is necessary to drill a through hole. The lid is removed, an additional hole in the form of a rectangle (through) is made in the side wall. A bunker will be filled through it with seeds.
  • We install a plastic pipe in the center of the jar so that the seed does not get enough sleep. A steel pipe is installed in it, a bolt with a nut is screwed. The rotational mechanism is ready.
  • The bunker is made to the side of the points under the holes at a distance of 30 mm. Then they are pierced with a hot clove. Seeds should go into holes.
  • Make a pen. A through hole is drilled in a wooden cuttings at the end. Using a bolt and nut, attach a handle to a seeder.
  • To automate the process, make a device from an iron sheet for filling planting holes with seeds.
  • The workpiece is attached to the handle above the hopper with sowing material.
See also  How to thread an inch pipe

The device is ready. Before the start of sowing, it is recommended to prepare the site, loosen hardened soil.

walk, tractor, cultivate, soil

If the independent manufacture of a landing unit causes difficulties, it is recommended to purchase finished designs immediately. The assortment in the market is quite large. American accurate sowing model “1001. B” is equipped with 6 interchangeable discs. With such a seeder, you can plant 28 types of vegetable crops. Using the adjusting screw, you can change the depth of landings.

walk, tractor, cultivate, soil

Sighters “Newthagro” belong to single.Row types. Designed for crops of beets, carrots, onion crops, cabbage. But such designs are expensive.

But there are cheaper analogues. Accurate seeders “SOR. 1/1”. They are also single.Row, can be equipped with a sleeve or brush sowing unit, the marker of the rows is 0.5 m. This is enough for the middle garden.

The use of a manual seeder can significantly reduce labor costs, increases the speed of the planting process, simplifies the technology, significantly improves the quality of crops, and hence the production of excellent yields in the future.

Homemades for a walk.Behind tractor

The question of what to start constructing attachments for walk.Behind engines is quite reasonable. The fact is that almost all motoblocks are equipped with trailed devices, a factory model, designed for the use of standard types of equipment. It is necessary to clarify that it is the standard equipment that does not satisfy the requests of customers. Trailed systems are too tender and fragile when using them in strict operating conditions.

For domestic motoblocks, trailed devices are mainly made of steel in a welded way, but for mass production, it is mainly cast.Iron casting, or a alloy of metals. It is clear that for one corps plow, even the most powerful adapter from cast iron will not withstand.

Therefore, the first one needs to be created is a trailer with your own hands for a plow. It is better to accept the standard scheme as a basis for the design. The adapter is a hinge with the possibility of fixing the plow in different positions, which is especially convenient for plowing small areas when the plow is used with both the left and right dumps.

The adapter itself is recommended to be made with the possibility of fixing not only in vertical, but also horizontal planes using talreps and bolt compounds.

This option will help to use it for plowing, and for hilling, and to install an adapter-stage for mowing or rakes for turning hay on haymaking.

Universal trailer for the motor

The presence of a trailer provides mobility, because it is one thing to conduct a one.Axle tractor with already installed units, the other, when a plow, milling cutter or potato.Resident are simply loaded onto the trailer and transported by the walk.Behind tractor itself.

It is necessary to calculate the parameters of trailer equipment for the walk.Behind tractor based on its power, the principle here is simple. 1 liter. With. Means the possibility of transporting 100 kg of healthy cargo on the cart. The simplest and most reliable is the scheme of the single.Axis trailer with the load on the central axis. And although the carrying capacity of such a trailer is small, only up to 500 kg, this is enough to install the seat on the trailer and control the walk.Behind tractor sitting on the trailer.

The most difficult thing here is to choose the necessary components. The easiest way to use ready.Made details. For example, a do.It.Yourself motor block is made from car, for cars. This allows you to use standard automobile wheels and tires to equip the unit. On the other hand, the hub from the VAZ classics is perfect in order to make other useful homemans. Soil.Spaces, winches, and weighting wheels.

For the trailer, the design of a rectangular pipe is mainly used, but a channel and a heller can be used as a frame base. The sides for the trailer are best provided for removable. It is preferable to immediately provide for the possibility of installing several types of sides on the platform:

  • Wooden or metal for the transport of bulk cargo;
  • Light, mesh for harvesting green mass for animals;
  • Folding, with the possibility of increasing useful area for hay transportation.

But in order to make it comfortable to move along the roads, it is worth making wings on a single tractor. If possible, immediately install mudguards on them. After all, not on all roads there is asphalt and solid coating.

It is impossible to call the same.Based tractor with the trailer according to the law, but this does not mean that the trailer should not be equipped with light alarm means.

Be sure to install at least 4 reflective elements on the trailer. 2 red in color and 2 white in front. This will help the driver of the car determine the wagon in the dark.

See also  How to make a hedgehog for a walk -behind tractor. How to build hedgehogs for attaching to a walk -behind tractor?

Soil processing tools. A plow and a plow for a walk.Behind tractor with your own hands

Before you make a hitch on a single.Based tractor for soil processing, it should be decided what is more important and prioritize in the technique of processing the site. For large areas used for planting potatoes, root crops, grain crops, the best option would be a plow for a walk.Behind tractor with your own hands. Making it easier and easier. But for the beds for vegetable crops, to process strips between the rows of the garden or final processing for planting, it is better to make a cutter. This will greatly facilitate further work.

With the finished hitch on the uniform tractor, its shape is the most difficult to manufacture the plow. The case has a shape complex for forming and therefore it is better to make a plow from several components. Do.It.Yourself School for a walk.Behind tractor is better to make from steel. A great effort that will experience this element should not lead to its deformation. Over, it is the Soshnik who is responsible for the depth of lowering the plow.

The plow’s plow. This is the part of the plow that crashes into the ground and cuts its layer. The strength and power of this element will allow you to work with the plow both in the conditions of the processed arable land, and do the preparation of the virgin lands. Despite the complexity of the design of the dump to make it quite simple. For a curved dump, it is better to take a ready.Made round or oval shape already finished workpiece. Make a dump from it according to the drawing. Smarts for this usually use large pipes from 350 mm in diameter or gas cylinders. The dump is almost perfect in shape.

One of the questions how to make a plow for a walk.Behind tract will be the manufacture of a field board. A stabilizing element for a plow that sets the direction of its movement when working on arable land.

DIY plow for a walk.Behind tract in the same way as the plow is assembled from several elements. True, for the use of plowing in soil processing, it is better to provide a dump from the reinforcement, so that during processing the soil is as much as possible to growl when turning the layer. In the design of the plow, it is better to provide not a frontal dump, but a bilateral dump with reinforcing bars.

Cutters for the walk.Behind tractor Neva assembly, cultivation, review and reviews of owners

Cutters are the main active element in the cultivation of the soil. They exist several types. Each of them is suitable for processing a certain soil, and with a certain speed.

Using Walk-behind Tractor for Land Cultivation

  • How high.Quality the final result of soil processing will be;
  • How much will need to make efforts for this;
  • What will be the controllability of the motor block during cultivation;
  • How much the engine will be loaded.

First of all, the choice of cutters should occur depending on which soil will be processed, t.E. Where, on which land he will work.

Cultivator cutters are an integral part of any walk-behind tractor. This is one of the first hinged devices to purchase.

However, there are situations when the standard cultivator is not installed that cutter that is necessary.For example, it does not fit the width of the processed surface or does not penetrate the ground deep enough. In this case, you can purchase additional cutters for the Neva walk.Behind tractor, which can perform the necessary volume of work.

This is how the earth plowing the Earth with the Neva with eight mills occurs:

By changing the number of installed mills, you can optimize the work of the entire Neva walk.Behind tractor during cultivation, improve its handling and the final result of loosened soil.

If you have to cultivate clay soil, then you should not install more than two pairs of milling for cultivation. Since otherwise there will be a huge load on the engine of the walk.Behind tractor. And instead of a good result of cultivation, we get a faulty engine. Over, the manufacturer is not recommended to increase the amount of milling cutters when working with the lands of virgin lands, since the soil there has a large number of stones and other organic compounds.

It is recommended to put mills only when working with an already prepared land. In this case, the cultivation of the Neva by the motornote with the mill will bring an excellent result.

How deep the cutters will penetrate into the ground, will depend on a pre.Exhibited adjustment, which is carried out with the help of a coupon. This is a steel anchor, which is located vertically at the hitch of the cultivator.

| Denial of responsibility | Contacts |RSS