How to install a starter on a trimmer for grass

To repair the starter of the trimmer for the grass, you will need to disassemble it first, and then collect it. This process is not a particularly difficult occupation. For work, you will need a screwdriver with the tip of the desired shape.

Everything should be done carefully, observing safety precautions, mainly that the spring does not injure the master if an accident.

Parsing the starting node

They disassemble the launch mechanism in order to install new parts instead of broken in the following sequence:

  • Spin a screw with a screwdriver, fixing the pulley with a starter lid;
  • Take out a spring and antennae;
  • Remove carefully with the pulley (you need to unscrew the head or work, having dressed the glasses and gloves before);
  • Determine why the launch mechanism has broken;
  • If the spring collapses almost completely, then it is replaced;
  • When the spring exits from the hook, it is installed in the original place, bending the antennae before this (the photographs show the laying process);

After the spring plate is installed inside the groove, it is carefully twisted. To change the spring, you should work carefully and accurately: it can, under the influence of the effort caused by the installation of it in place, accidentally burst

Even if you carefully remove the video, then the spring strip flies very quickly from the coil and can injure your hand with its sharp edges

To change the spring, you should work carefully and accurately: it can, under the influence of the effort caused by the installation of it in place, accidentally burst

Even if you carefully remove the video, then the spring strip flies very quickly from the coil and can injure your hand with its sharp edges

Immediately putting a springy plate in the same place does not always work. It often slips, so attempts are required to repeat until the desired result is achieved.

How to fix grass cutter starter

Starter assembly

The assembly of the starting node is carried out in a number of stages:

The coil is turned over, installing it so that the spring bend exactly stands into the groove of the case, as in the photo below;

When making the stated manipulations, it is necessary to lay two goals. If this is not done, then the spring over time damage the plastic cup, and when it is pulled. Because of this, a feeling appears, as if the spring had flown. To eliminate such a drawback, you need to install this part of a larger length or an additional goal.

When such spare parts are absent, you can just unscrew the screw a little, and the starter knot will begin to work without shaken. But this option is temporary. It is better to repair qualitatively as quickly as possible.

Spring tension

After installing the spring, it should be pulled. The following actions are performed for this:

  • Remove the handle from the starter cord;
  • Then the rope is inserted into the coil groove;
  • They stretch the spring, rotating the coil in the direction opposite to the clock of the clock arrow (reviews);
  • Make the desired number of revolutions specified in the instructions for the use of the trimmer model used and the corresponding length of the cord used;
  • At the very end, the rope is threaded into a hole designed for this, located in the starter cover;
  • Put the handle in place, fixing it with a node.

If after the repair the spring continues to fly, then you can get rid of this in the following ways:

  • Squeeze the suitable piece of the plate into the groove at the location of the spring hook;
  • Drill holes on two sides of the groove in the coil, into which the spring hook is inserted and fix it using a wire.

Replacing a torn cord

A torn rope is replaced in the following sequence:

  • The old cord is removed;
  • Choose a suitable rope (thickness and length);
  • Having reached it through a special hole in the coil, a knot is tied;
  • Sprinkle a spring, producing the required number of revolutions;
  • Fix the pen.

It is better to stretch the spring plate along with the partner so that the edge of the cord does not hit the starter mechanism.

It is easy to assemble a starter on a trimmer and wound a spring, only you should do it carefully and with caution. For different models, the gas tanks of the launching mechanisms are the same, so they are repaired in a similar way

In this case, there are some nuances associated with their constructive features.

What is the starter of the MTZ

MTZ gasoline starters have type PD-10. When it starts, the gearboxes begin to transfer the torque to the power unit, gradually rotating it. The advantage of a gasoline device. Unpretentiousness, the ability to use high.Quality fuel for work, does not affect performance at all.

An electric device is also installed on MTZ-80, which is powered through a special mechanism connected to the battery. Typically, this type is necessary for tractors with powerful engines designed to perform constant loads and constant work. Electric requires a mandatory connection to the engine so that the clutch can transfer the torque to the flywheel.

Thus, which the starter is best put on the MTZ, the owner of the tractor must choose on his own. Modernization depends on the type of work performed and the technical characteristics of the machine itself. Climatic and weather conditions are also important. In the warm season or in regions where there are a lot of sun, you need not a very powerful motor. Therefore, for winter, it is recommended to use ordinary gasoline type PD-10, and in the summer they prefer to replace it with electric.

Removing and disassembling the starter, replacing broken parts

To repair the starter of the trimmer for the grass, it first needs to be disassembled, and then collect it. This process is not particularly complicated. You will need to work the shape of the screwdriver.

See also  How to choose the right grass trimmer for the grass

Everything should be done carefully, observing precautions, especially so that the spring does not injure the owner in case of accidental departure

Starting analysis

Disassemble the starter mechanism to install new parts instead of broken in the following sequence:

Unscrew the screw that attaches the pulley with the starter lid using a screwdriver; Remove the spring and antennae; Carefully remove the pulley (you need to turn your head or work, after putting on your glasses and gloves); Determine why the trigger worked; If the spring fell apart almost completely, it is replaced; Когда пружина выходит из крючка, она устанавливается на прежнее место, предварительно сгибая антенну (фотографии показывают процесс установки);

After the spring plate is installed inside the groove, carefully tighten it. To change the spring, the work must be performed carefully and accurately: it can accidentally explode under the influence of the force caused by its bringing into effect

Even if you carefully remove the video, the spring tape is very quickly torn off the coil and can injure the hand with sharp edges

To change the spring, the work must be performed carefully and accurately: it can accidentally explode under the influence of the force caused by its bringing into effect. Even if you carefully remove the video, the spring tape is very quickly torn off the coil and can injure the hand with sharp edges.

Immediately put in place a spring plate does not always work. This often slips, so attempts should be repeated to achieve the desired result.

Starter assembly

The assembly of the starting installation is carried out in several stages:

The coil turns over, installing it so that the bend of the spring accurately fits into the groove of the case, as in the photo below;

When making the above manipulations, it is necessary to put two goals. If this is not done, the spring will ultimately damage the plastic cup, and when it is removed, jamming will begin. This makes you feel that spring has come. To eliminate this drawback, it is necessary to install this part of a larger length or an additional goal.

When such details are not enough, you can just unscrew the screw a little, and the starter assembly will start working without fixing. But this option is temporary. It is better to repair it as soon as possible.

Spring tension

After installing the spring, tighten it. To do this, follow the following actions:

  • Remove the handle from the starter cord;
  • Then the rope is inserted into the groove of the coil;
  • The spring is delayed by the rotation of the turn in the opposite direction clockwise (winding);
  • Make the required number of revolutions specified in the operating instructions for the used trimmer model for grass, and the corresponding length of the cord used;
  • At the very end, the rope is lowered into the hole provided for this, located in the starter cover;
  • Place the handle in place by fixing it with a node.

Read what gasoline is pouring into the Husqvarna lawn mower

If after the repair the spring continues to fly, you can get rid of it in the following ways:

  • Insert the corresponding piece of the plate into the groove at the location of the spring hook;
  • Drill holes on both sides of the groove in the coil, into which you need to insert a spring hook and fix it with wire.

Replacing a torn cord

A torn cable is replaced in the following sequence:

  • The old cord is removed;
  • Choose a rope of a suitable size (thickness and length);
  • Having passed it through a special hole located in the coil, tie a knot;
  • Spring valve producing the required number of revolutions;
  • Fix the pen

It is better to tighten the spring plate with Partner so that the edge of the cord does not twist inside the starter mechanism.

It is not difficult to assemble a starter on a trimmer and wound a spring, but this must be done carefully and carefully. For different models of gasoline engines, the breakdown of the starting mechanisms are the same, so they are repaired the same

However, there are some nuances associated with their constructive features.

How to repair a starter on a trimmer

Repair of the starter of a gasoline trimmer for grass may be required at the most inopportune moment. With all this, you can solve the case with 2 methods: change the broken part or change the entire node. The latter option will cost more. To repair the device with your own hands in most cases Only a screwdriver with a suitable tip is useful from the tools. Repair work will not take much time and do not require special knowledge. It is enough to know the device, the mechanism of work, aspects of the assembly and disassembly of the starter on trimmer, to achieve a good good result.

Backpack Blower Repair. Replacing the Starter Assembly (Echo Part # A050000330)

Collect the STIHL MS 180 saw back, quite simple, the main thing is to adhere to the next algorithm:

  • Install the piston on the connecting rod, the arrow on the piston should look along the stihl 180 chainsaw, and the side of the crankshaft, which is designed to install the flywheel;
  • Gently insert the piston back into the cylinder, the place for mounting the coil should be on the side where the flywheel is installed on the crankshaft;
  • Install bearings, seals, a stop ring on the shaft and lower everything assembled to the seat in the cylinder;
  • Next, degrease the place of installation of the crankcase and the crankcase itself, then smear with sealant and installing in place to tighten 4 screws of fastening;

To collect the STIHL 180 saw after the engine is assembled, you need to observe the reverse sequence of disassembly

It is important to treat the process carefully and not forget to set the thrust on the carburetor, and connect the ignition wire

Below you can watch the disassembly of the STIHL 180 on the video, it is made for inexperienced users, it shows in detail the whole process.

Dismantling the chainsaw of the Stihl 180 chainsaw and its assembly, if there is a certain experience, it is quite simple, the main thing is to clean the saw well before work and not rush. In order for small details not to be lost, you need to use containers in which, in the process, you should lay out spare parts.

With the advent of the summer of many owners of personal plots, the question is disturbed by a knitted for the purpose of putting a knife on a trimmer for grass. The questions are more burning, why and when it is targeted to replace the fishing line for a trimmer on a motorcycle with a stronger cutting element. In our article, we will try to make a complete set and give useful advice to summer residents.

See also  How high can you mow grass with a lawn mower?

A trimmer for grass with a knife installed at this address is most conveniently used for a more comfortable mowing of the highest and coarse grass that was coarse in the country. A fishing line for a trimmer on a motorcycle in this version does not cooperate. Narrow in a short time vomit. The implementation of Tolstoy 5.3 mm of the cord or homemade rods with cables forces the vegetation to wind up on the rogue. This increases the load on the engine. As a result, a piston group and the remaining movable units of the unit wear out in a short time.

starter, trimmer, grass, lawn

If the mowing of a weeds is created by an electronic trimmer without a knife, only with a fishing line, even a thick with a figure section, the work cannot be solved. There is always a risk of overheating the electric motor and disable flexible shaft. And the matter is what remains to make our client in a large rotating moment of the electronic motor. The grass wound on a spindle makes strong resistance to the shaft resembling a speedometer cable that does not withstand and twist.

To protect the equipment from early wear, domestic manufacturers have provided the possibility of installing special knives on grass for grass. The design and shape of the existing cutting parts allows you to easily be controlled not only with coarse and outgrown with grass, and it is successful to fight with young shrub.

Before taking and putting a knife on a motorcycle, we will find out what they are and where are used. Now domestic manufacturers offer the consumer many types of these consumables. As a result, the entire cutting tool created for mowing grass can be systematized:

The device and principle of operation of the starter on the trimmer

The gasoline engine is, in principle, the main part of the motorcycles its power lies in the range of 0.5-2.5 liters.With. The movement from it is transmitted by the shaft located inside the hollow bar, and then through the gearbox, consisting of gears, already a fishing line or a knife (working body).

Also, the lawn mower has the following elements:

  • Protective casing;
  • Lever;
  • A belt designed for ease of use of the device;
  • Starter serving for launching a gasoline internal combustion engine.

All parts of the motorcycles are presented in the photo further.

The starter on the trimmer is an integral part, which performs the engine starting into operation. It is shown separately in two photos below.

The starter mechanisms of various models of benzos work according to the same principle: during the launch of the ICE, the protrusions marked in the photograph above the number 1 are included in the hook with dogs 3. When the engine begins to work, they return to their previous position due to the effects of centrifugal. Similar role is also played by wires 2.

The process of returning to the initial position of the elements of the mechanism occurs due to the presence of a spring screwed around the axis. It unfolds when the rope is pulled. After releasing the cord, it is drawn and winding due to folding the spring. During the launch of the ICE of the lawn mower, the triggering mechanism turns its shaft until it starts to work (starts).

To date, gasoline motorcycles are equipped with two types of starter mechanisms:

The first option is much more common.

The starter on the trimmer can function without breakdowns for a long time. It is impossible to unambiguously indicate the deadline. Everything is determined by the initial quality of the device and compliance with the rules of handling it.

Replacing a torn cord

A torn rope is replaced in the following sequence:

  • The old cord is removed;
  • Choose a suitable rope (thickness and length);
  • Having reached it through a special hole in the coil, a knot is tied;
  • Sprinkle a spring, producing the required number of revolutions;
  • Fix the pen.

It is better to stretch the spring plate along with the partner so that the edge of the cord does not hit the starter mechanism.

It is easy to assemble a starter on a trimmer and wound a spring, only you should do it carefully and with caution. For different models, the gas tanks of the launching mechanisms are the same, so they are repaired in a similar way. In this case, there are some nuances associated with their constructive features

In this case, there are some nuances associated with their constructive features.

The main malfunctions of the starter of the trimmer for grass

Find the reason for the breakdown of the starting device is easy. There are several main options:

The designated details are shown in the photo below.

It may happen that the starting mechanism will be broken by the case. The consequences will turn out to be deplorable if the ragged rope is wound around the flywheel of a working internal combustion engine: then the spring bursts, the pulley will tear off. But such cases when a complete replacement of the starting node is required, very occasionally occur. In most cases, to fix the mechanism, it is enough to put a new spring or replace the cord.

Important! When winding and installing the spring, it should be remembered that it is hot, which means that it can burst if you make too much effort. The new part is inexpensive, but you will have to spend time on its search, which means that work on mowing the grass will move endlessly.

To wind the spring, it is necessary to place the bend in the groove, and then, rotating the coil, carefully lay the part along the inner diameter of the coil. In this case, the spring should constantly hold on. If it is not fixed, the part slides and jumped out, then you must again wind. With proper execution, the spring fit tightly to its saddle.

Replacement of the cord

To replace the element in the coil, you need to find the hole through which the cord passes, and then tie the knot. Next, you will need to wind the coil for several revolutions.

The note! You can find out the exact number of revolutions by reading the instructions of the trimmer for grass or manually. To do this, measure the length of the rope and calculate how many times it can be wrapped around the coil.

For example, if the cord rotates in a circle six times, then to tighten the spring, you need to turn the coil by the clock six times. After that, you just need to let the rope through the hole and fix the handle on the cord.

See also  What's the difference between a regular lawnmower and a rotary mower?

starter, trimmer, grass, lawn

Other malfunctions

Sometimes after repair, spring still flies. There are two solutions to this problem:

  • So that the bending spring does not jump out of the groove, between the bend and the seat wall, you need to insert a small piece of a metal plate. This will provide a tighter fixation of the spring.
  • Holding the spring in the groove also helps with home installation. It is necessary to drill holes in the coil on each side of the groove, place a spring bend in them and fix it with a piece of wire. These steps should be made so that the wire does not touch the starter cover and slow down the movement of the pulley.

Assembly and installation instead of a starter

To collect the starter and install it in the same place, you need:

  • Turn the pulley with a spring down and place it inside the case so that the bend of the spring falls exactly into the hull groove;
  • Install the puck, then the spring, on top of it. Second washer;
  • Place the antenna cup on the puck and plunge the screw.

When assembling, be sure to install both goals, otherwise after some time the plastic cup will be damaged by the spring, and when the cord is stretched, the user will notice that it jammed. It looks like spring has come. To correct such a breakdown, it is necessary to install a larger screw or another washer. If you cannot find the details you need, just unscrew the screw slightly, and the starter will no longer jam. However, you must understand that these are temporary measures and that you should correct the problem as soon as possible.

Prevention of problems

Sooner or later, problems with the starter arise on any trimmer. STIHL FS 55, MTD 790 or other brand. This malfunction can be postponed, but the tool should be treated carefully. In particular, do not make too sharp jerks, it will break the cord or spring. It is not recommended to expose a brush to impacts or other physical influences. In the case of a breakdown of the starter case and the cut of the cord, it can be wound on the engine flywheel. It will break the pulley and break the spring.

Therefore, having discovered that the executive mechanism has broken on the uterus, do not immediately rush with the help of specialists. Knowing how to eliminate problems and / or replace the details, you can carry out repair work yourself. This does not require a special tool. At first, the procedure may seem complex and tiring, but numerous online video on the repair of the starter can help you solve the problem as quickly and easily as possible.

The best gas braids for grass

Trimmer for Husqvarna 128R grass on Yandex market

Trimmer for Husqvarna 128R grass on Yandex market

A hand starter for a gas trimmer for grass or gas trimmer for grass is a mechanical assembly, which includes a ratchet. On the pulley in the starting position, wind the cable. In the beginning it is extracted. Loof pulley. If you let go of the end of the rope, he will turn back. Flat tape folded in a ring is used as a spring. This resembles a spring in large mechanical watches that are launched once a day. The starter itself is located more often than closer to the front end of a mowing or trimmer for grass. To correctly perform all manipulations with the starter of the Kustorez, you need to know the features and settings of the device.

Asseting device and common malfunctions

The easiest way to give the lawn mower for repairs, allocating a certain amount of funds from the family budget, operational and high.Quality repair with your own hands is no less simple and convenient to understand the design of the lawn mower and fix all the problems.

The massive and piece manufacture of trimmers is based on the use of generally accepted technology, the typical design scheme consists of certain elements and parts, it is important to know them when carrying out independent repair work:

  • Top part. The basis of the entire structure, where all important elements are collected, such as the starter, carburetor and the engine of the lawn mower;
  • Middle part. Hollow rod, inside it is a cable connecting the engine and gearbox, which sets the cutting fishing line for the trimmer. In this part there are mounts for the distribution of weight of the entire structure and a belt for fixing a trimmer for grass on a belt of a person using a trimmer for grass for its intended purpose;
  • Bottom part. It has a gearbox and cutting elements that are hidden under a practical casing, which protects the user. The casing provides an increased level of safety, preventing large fractions of garbage, pebbles and glass in a person while working with a gas station.

This is interesting: adjusting the carburetor of the motorcycle Ural

Knowing the internal device and the principle of operation of the trimmer for grass, you can independently carry out repair measures for the design or replace individual unusability of the nodes using the repair instructions.

The most common and often encountered, subject to independent correction of the breakdown of the unit can be called the following problems:

  • Engine malfunction, due to which the lawn mower is not started and does not work;
  • Enhanced vibration of the bar motorcosa, which complicates its targeted use;
  • Increased overheating of the gearbox, its accelerated heating during operation;
  • Slow and weak functioning of the cutting fishing line at insufficient speeds;
  • The clogging of the starter grill causing the engine overheating and its refusal to work;
  • Rapid and frequent clogging of the carburetor due to the use of poor.Quality fuel;
  • Clogging of the air filter in case of non.Compliance with measures to care for the device.

All these problems can lead to the fact that the device will lose its ability to work before ordering the necessary spare parts for non.Bosomeds should be carried out by a visual inspection and diagnosis of the device.

Special attention is required by individual spare parts and assemblies of the device, to verify them, you will not have to turn to a professional master, a complex of diagnostic measures will help to identify a consequence of the occurrence of a loss of performance.

| Denial of responsibility | Contacts |RSS