Repair of a trimmer coil for the grass with your own hands: how to remove, disassemble, change a fishing line for a trimmer, assemble and install back

In this article, we will describe in detail the procedure for how to remove the coil of the trimmer for the grass. Step.by.step instructions with the attached video will help a beginner and an experienced user to independently remove the element of the system and clean it or replace it with a new. Before you remove the trimmer coil for the grass, it must be drowned out. for gasoline samples or disables power. for electrimaters. We will demonstrate one traditional dismantling scheme, but in different models of trimmers, the method of attaching the coil to the tool may vary. With your own hands, you can not only remove the old sample of the coil, but also change it to a new one, if such a need arose. So, a step.by.step script:

  • Disconnect the tool from the network or turn off the engine (for benzos).
  • Carefully remove the cap of the coil, holding a spiral spring in place.
  • Click on clamps symmetrically located on both sides with one hand, and the second carefully remove the lid.
  • We are looking for a hole in the gearbox cup located on the side or from above, and combine it with the same hole in the shaft hub.
  • Using a playground key or a metal rod-we spread it into the gearbox hole, excluding the possible enlarge of the shaft.
  • Remove the mowing bobbin on which the fishing line for the trimmer is wound.
  • A slightly drowned screw will be visible in the depths. It can be unscrewed by a cruciferous or slotted screwdriver.
  • With one hand we hold the body of the head, and the second, counterclockwise, unscrew the screw.
  • Light swaying. remove the mowing head. Even if it acidified a little, we make delicately more efforts and with the same swaying. we remove it. Often movements are produced at the watch arrow, but coils are also found that are unscrewed in the other direction.
  • The assembly takes place in the opposite sequence.
remove, trimmer, cover, grass, fishing, line

Removing the bobbin has to be removed in cases of damage, winding of the fishing line (which is undesirable and indicates an illiterate selection of gear), and also when you need to wind a new cord with a new coil or replace the cutting tackle. Buy a coil for a trimmer for grass will always be inexpensively offered by the Kosikosa store.

The procedure for removing a mowing head of a trimmer for grass.

The design and fastening of the working part of the electric cocia differs significantly in different companies of manufacturers. But taking into account that in our markets there are many copies of acceptable recognizable brands, the order described can suit the owners and other portable garden equipment for the care of the lawn and grass.

Trammering head replacement tool.

For replacement, removing the head of the instrument, a nozzle in the form of a star will be useful to us, usually comes with the kit, or a flat wide screwdriver. Use a hexagon of a knife stars will not work, the nozzle slides, licking the edges of the sprocket on the screw.

Installation of a mowing head on a trimmer for grass Black and Decker.

Installation of a mowing head on a trimmer for grass is done in a flip sequence. When installing the screw in place, it is delayed by average effort.

I wish you a successful summer season and so that the garden technique does not fail. I hope my tips on how to remove the mowing head on the BlackDecker GL716 trimmer saved time and nerves for you.

Trimmer head with two antennae

After extracting the spray from the coil body, we determine the number of streams for winding fishing line (1 or 2). There is no principle distinction between bobbins with one and 2 grooves, but with a negligent refueling in a paired groove there is a place to be confused with the operation. Due to the likelihood of interweaving with a tool adjacent, a situation may appear when, after the wear of the workers’ antennae, it is unrealistic to extract new.

Regardless of the number of streams for refueling, a fishing line is taken for a trimmer from 1 length.5 to 3 meters. The winding needs to be created in a flip rotation of the head to the side, because the winding in the direction of movement will lead to the fact that the fishing line for the trimmer will not be removed from the bobbin. After the fishing line for the trimmer is tucked into the coil of the trimmer for the grass, free ends (15-30 cm) we stretch into special holes. Next, collect the head in the back of the order and check the performance. Do not worry if the ends of the 2nd antenpers are very different in size, since when the trimmer for the grass is launched, the knife installed on protection will cut off excess.

What you need to know about the fishing line on the trimmer for the grass

Fishing lines is called consumable, which consists of nylon, and serves as a cutting device. Through this equipment, the grass grows, which is ensured due to rotation of the instrument head with a high frequency. This material has a different thickness, which depends on its use on the corresponding tools of low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers for grass with motorcycles (from 2.4 up to 3.2 mm).

The more powerful the tool, the accordingly there should be a cutting equipment. This affects not only the quality of the injection of grass, but also on the life of the material. If you ask the question of how to wind the coil of a trimmer for grass, then it’s time to change the reload of the tool. With the onset of spring, this issue is becoming more and more in demand, so it’s time to understand the step.by.step instructions for replacing the fishing line in the coil of the trimmer for grass.

Which fishing line for a trimmer to choose to refuel a lawn mower

The thickness of the polyethylene thread depends on the model of the technique and varies from 1.2 to 4 mm. She may be:

  • With a round section. this is the most durable material for mowing herbaceous plants;
  • with curly section. used to mow soft plants;
  • twisted. used for thin grass;
  • professional type, is not suitable for all models of technology.

To change the fishing line for a trimmer on a lawn mower, it is necessary to purchase a cutting thread that will be ideal for a particular type of mower.

Criterias of choice

You can soak the thread in a basin of water for several minutes to increase elasticity and strength.

How to remove a coil from a trimmer for grass and extract a fishing line for a trimmer

Initially, before filling the fishing line for the trimmer to the coil of the trimmer for the grass, it is necessary to extract it from there. Coil or tip is a device that is located inside the braid, bobbin or drum. The heads are of different types (depending on the manufacturers), however, the principle of replacing the fishing line on the coil has the same. First of all, we will figure out how to remove the head from the tool, as well as how to get a drum with a fishing line from it.

It is interesting!The replacement of equipment can be done directly on the tool, but if you do it for the first time, it is still recommended to remove the head, and study the detailed process of winding. After the technology is mastered, you can perform work on replacement on a trimmer of a motorcycle or a gas station. Instructions on how to promote a hand head on a trimmer, has the following look:

    Turn the instrument with the head to the top, and if necessary, cleanse it from pollution. Take two fingers of one hand by the cover of the cover (on the mowing head), which are located symmetrically to each other. After a light pressed inward, dismantle the protective cover from the drum

This process is not difficult, and as you know, it is not necessary to dismantle the entire head if you know how replacement is performed. When dismantling, consider the following nuances:

  • It is recommended to remove the head periodically to prevent the corrosion of the threaded connection. If you never unscrew the screw, then if necessary to do it will be difficult and even sometimes impossible
  • If the screw has a tetrahedral boring of the head, then for twisting you should select a screwdriver or bit of a suitable size to eliminate the licking of the faces on the head
  • When assembling the installation, a threaded seat should be treated with lubricants, for example, solidol or machine oil
  • If the edges on the screw are licked, then for its unscruptions you can use special clamping forceps
  • There are drums that do not require preliminary disassembly. To dismantle them, you should take up it, and rotate in the opposite direction of the direction of the clockwise

Knowing how to disassemble the drum, you should continue to clarify the process of replacing a trimmer fishing line for grass. Below the video shows a detailed process how to open a trimmer coil for grass and disassemble it.

Instructions

In order to change the fishing line for the trimmer, it is necessary to extract the old one (if it was).

The coil is part of the design of the trimmer for the grass, which is located inside the head of the motorcosa, drum or bobbin. Depending on the manufacturers of the head can be different. But this article discusses only Patriot, although their mechanism is used by many other companies.

Now you need to understand how to properly remove the head from a trimmer for grass and how to get a drum out of it.

remove, trimmer, cover, grass, fishing, line

Instructions on how to promote a hand head on a trimmer is described below.

  • First of all, you need to clean the head of dirt and adhering grass if it is contaminated. To do this, you need to raise a motorcycle head up and, holding the casing, remove a special protective cover dressed on the drum.
  • The next step needs to remove the reel from the drum. The coil is easily removed even with one hand, because it is not fixed inside the drum.
  • The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with a coil, while twist the screw counterclockwise.
  • Now you can pull the coil out. As mentioned above, it is not fixed in anything except a hook with a metal shaft, so it does not need to be torn off with force. Neatly, in a circular movement you should pull the coil from the drum.
  • Now it remains to extract an old fishing line for a trimmer and follow the following instructions.

Installation of the coil and drum in its former place is performed according to the opposite algorithm.

Before the process of refueling the fishing line, it is worth making sure that the thread suitable for a trimmer was bought. In the case when the thread is not suitable, the fuel or energy consumption increases, as well as the load on the motor motor.

In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m fishing line. A specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the coil itself. If it is not possible to accurately determine the length, it can be done as follows: insert and wind the thread to such a state that the coil is completely charged (the level of the fishing line will be compared with protrusions in the sides of the coil). It is necessary to ensure that the fishing line for the trimmer sits in the coil exactly.

Do not forget that the thick thread will be shorter than thin.

The instructions for refueling the fishing line in the coil is described below.

  • The prepared thread must be taken and turned in half. It should be ensured that one edge is longer than the other by 0.1-0.15 m.
  • Now you need to take the ends in different hands. The one that is smaller must be pulled to more, so that it becomes 2 times shorter. When bending, the indentation should be maintained at 0.15m.
  • Find the slot inside the coil partition. Carefully prick the loop that turned out earlier in this slot.
  • To continue work, it is necessary to determine the direction of winding the thread in the coil. To do this, just examine the coil. there should be an arrow on it.
  • If the gunner could not be found, it is quite possible that there is a written designation. An example is given in the photo below. It is necessary to inspect the head of the coil. It has a direction indicator. However, this is the direction of the coil movement. To get the direction of winding, you need to wind in the opposite direction.
  • Now you need to season the reel with a fishing line. It is worth noting that there are special guide grooves inside the coil. When wrapping a thread, you need to follow these grooves, otherwise you can damage a trimmer for grass. At this stage, you need to charge the coil very carefully.
  • When the user winds up almost the entire thread, you should take the short end (do not forget about the protrusion of 0.15m) and stretch it into the hole located in the coil wall. Now you need to repeat this action similarly with another end (on the other hand).
  • Put the coil itself in the coil head, before that, extinguishing a fishing line for a trimmer through the holes inside the drum.
  • Now is the time to return the drum to your place. After that, you need to take with both hands by the ends of the fishing line and pull them to the sides. Then you need to put the lid in place (here you can safely make efforts until a characteristic click is heard).
  • Remained to perform “cosmetic work”. You need to see if the thread has come out too long. You can start a trimmer for the grass and check in practice whether everything is comfortable. If the thread came out a little long, you can cut it with scissors.

Trimmer heads: types and principle of action

The domestic market offers the owners of trimmers of the coil of several types: manual, semi.automatic, automatic and universal. They differ from each other in both the way of serving the fishing line and the principle of its charging. You can also wound a fishing line for a trimmer in different ways. According to this principle, the coils are classified into quick.charged and collapsible.

Before you purchase a trimmer for grass and/or buy spare coils for it, you must definitely familiarize yourself with which consumables are suitable for a particular model. This is important, since bobbins of different manufacturers can differ not only in the methods of supply and refueling of the cord, but also to the axis of the mount, type of thread, as well as the diameter of the fishing line used. For example:

  • The fastening axis can be fixed (fixed) or rotating 90 °, 180 ° or 360 °;
  • For low.power trimmers, a fishing line for a trimmer with a diameter of 1.3 to 1.6 mm is suitable, and for more productive. up to 2.0 mm;
  • Professional trimmers for grass, as a rule, are equipped with universal heads with a diameter of the cutting cord from 2.5 to 4.0 mm.

What You Need To Know Before Buying A Battery Powered String Trimmer | Toro Flex Force 60V 16″

Advice! Experts recommend using string heads equipped with ball bearings, as they have an increased service life, while reducing the wear of incoming components. At the same time, for replacement, it is best to choose the bobbin of the manufacturer indicated in the operating guide for the grass for the grass, which in turn will allow you to correctly install the head on its drive.

Manual bobbins

A manual mowing head is a coil in which the cutting cord during wear is stretched by the owner of a trimmer for the grass on its own. To do this, turn off the tool, remove the head and with the help of hands stretch the fishing line for a trimmer to the required length. However, despite some inconvenience, this type of head is considered the most reliable.

Bobbins with semi.automatic control

The semi.automatic coil installed on the trimmer allows you to serve a fishing line for a trimmer using the centrifugal force that occurs when it rotates. In order for the supply to be carried out, you need to touch the head of the coil to the ground and at the same time press the button that opens the anchor mechanism. This key is located on the control handle. At the same time, turning off the trimmer for the grass is not required.

On a note! In the market of trimmer spare parts, semi.automatic coils of two types can be found: single.section, in which the fishing line for a trimmer is wound evenly on both sides, and two.section, where the cutting cord must be refueled separately in each section.

Bobbins with automatic control

In the automatic heads, the supply of the cutting cord occurs when the speed of the trimmer engine is changed. To pull the fishing line for the trimmer outward, reduce, and then increase the speed of rotation of the engine shaft. As a rule, the coils of this type are equipped with a metal core, due to which their breakdown is practically excluded.

Bobbins are universal

The universal type of heads differs from its analogues in that they can be installed on various models and electrimmers’ models. They are characterized by high strength and reliability during operation.

Bobbins are quick.charged

Coils of this type allow you to refuel a new fishing line for a trimmer without disassembly. To do this, one of the ends of the cutting cord is stuck inside the bobbin, and then wrapped several times around its surface. After the required amount of fishing line is wound, the latter is cut off.

Bobbins collapsible

To refuel the fishing line into the head of this type, it must be removed from the grass.shirt and disassemble. Having wound the required amount of cutting cord, the coil is collected and returned to the place.

On a note! Currently, almost all electro- and benzotrimers are equipped with mowing heads that allow the fishing line for the trimmer to change to the knife.

The main malfunctions of the coil

Users of the electrimmer and lawn mower often face a problem associated with a semi.automatic braid head. Coil malfunctions can be as follows:

The fishing line for the trimmer does not extend automatically

If, with a light blow, the trimmer coil button for grass on the ground is not lengthened for a trimmer, then the reasons for this may be the following.

Option 1. there was a snack, t.e. Squeezing the cord between turns. This problem usually appears if the user wound a fishing line for a trimmer to the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the fishing line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, with even turns with good tension.

Option 2. too short ends protrude from the head. A fishing line for a trimmer may not exit when hitting the ground, if its ends sticking out of the head, insufficient length (short). In this case, the centrifugal force is not enough for the fishing line for the trimmer to stretch. Therefore, it is required to stop the unit (drown out the engine or turn off the ethletric trimmer for grass from the network) and pull the fishing line for the trimmer manually, after pressing the button.

2.50mm VS 3.00mm TRIMMER LINE/ FISHING LINE CUTTING THE GRASS/GRASS CUTTING,

Option 3. a fishing line for a trimmer was soldered inside a mowing head. This leads to the fact that the coil is stopped and does not spin when the button is pressed. Basically, this happens for several reasons: poor quality of the cord, overheating of the coil with prolonged operation of the unit, a fishing line on solid items.

  • In the first case, the cord of third.party manufacturers can be made of low.quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
  • But, if you still purchased a fishing line for a trimmer of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after refueling the cord, moisten it either with silicone grease (from the spray can) or mineral oil). This procedure greatly reduces the likelihood of soldering a fishing line among themselves.
  • Also, a fishing line for a trimmer can sleep if during a mowing it hit a hard object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open a trimmer coil for grass and rewind a fishing line for a trimmer.

The cord spontaneously lengthens

There are situations when a user of a trimmer for grass notices a very fast fishing line consumption. At the same time, he never hit the ground with a button to lengthen the fishing line. The reason that the fishing line for a trimmer spontaneously lengthens, cutting off a special knife on the casing of the device, may be the absence of a spring in a mowing head. Often beginner users of mowers, trying to charge a fishing line for a trimmer into a coil, forget to install a clamping spring in the head, or completely lose it when opening the lid, and in the future, they do not even suspect its existence.

Also, a fishing line for a trimmer can lengthen without using a button if the spring is weakened. If the spring check confirmed this fact, then it is necessary to put several goals under it to strengthen its clamping properties.

Fishing winding

Tramoring the fishing line in a trimmer coil for grass is a relatively simple procedure, provided that you adhere to a certain algorithm of action. When you need to determine how many meters of consumables are enough, wind it on the bobbin so that the skein does not exceed the diameter of the sides. Having decided on the length of the cord, follow the following instructions:

  • Fold the consumable material so that one end of the fishing line is 10-15 cm longer than the other.
  • You need to start charging with the central side, which divides the backpack of the trimmer for the grass into 2 parts. Find a groove where the cord should be inserted. The latter is bent twice.
  • Determine in which direction you need to wind the fishing line for the trimmer. To do this, take a look at the bobbin on which there can be an arrow or inscription. She indicates the side of winding. If there are no designations on the coil, then look at the arrow on the mowing head. carry out windings in the opposite direction.
  • Wash the consumable material carefully, a round to the round. Try to adhere to maximum thread tension.
  • After completing the cord laying, fasten first the short end of the material. To do this, insert it into the groove on the side of the coil, which is suitable in diameter. The second end (more authentic), attach to the groove on the other side of the backpack of the trimmer for the grass.
  • By fixing the fishing line for the trimmer, cut its ends. Do not forget to leave allowances about 10 cm.
  • Install the refitted coil to the mowing head of the device. To do this, you need to insert and pull the thread alternately into the weekend of the head, then place the keyboard of the device in the skin.
  • By applying the required force, pull the cord from the fixing grooves and tighten the material. At the end of this action, put on the lid and fix it using the latches.

The step.by.step winding of the fishing line on the coil to wind the cord per trimmer for the grass can be also in another way, in which two segments of the material are charged instead of one. The replacement is carried out like this:

  • Bend one end of the cord thread in the form of a hook.
  • At the bottom of the bobbin there should be a hole that is designed to fix the fishing line. Insert the bent over the end of the thread there.
  • Wind the cord material in the direction of the arrow to the desired level, which does not exceed the diameter of the coil of the trimmer for the grass.
  • The same actions need to be done for the second cell of the bobbin.
  • Assembly of the device head is similar to the first way.

How to wind a fishing line for a trimmer to a trimmer coil for grass: Key points

A gasoline or electric trimmer for grass is an indispensable assistant in the arsenal of a modern summer resident or owner of their own house.

Thanks to these garden devices, you can easily bake even a large personal plot. After acquiring this tool and performing several mowing, many people think about how to correct the fishing line for a trimmer to a trimmer coil for grass. For an inexperienced user, the first operation to replace it will seem problematic and laborious, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

Trimmer heads: types and principle of action

The domestic market offers the owners of trimmers of the coil of several types: manual, semi.automatic, automatic and universal. They differ from each other in both the way of serving the fishing line and the principle of its charging. You can also wound a fishing line for a trimmer in different ways. According to this principle, the coils are classified into quick.charged and collapsible.

Before you purchase a trimmer for grass and/or buy spare coils for it, you must definitely familiarize yourself with which consumables are suitable for a particular model. This is important, since bobbins of different manufacturers can differ not only in the methods of supply and refueling of the cord, but also to the axis of the mount, type of thread, as well as the diameter of the fishing line used. For example:

  • The fastening axis can be fixed (fixed) or rotating 90 °, 180 ° or 360 °;
  • For low.power trimmers, a fishing line for a trimmer with a diameter of 1.3 to 1.6 mm is suitable, and for more productive. up to 2.0 mm;
  • Professional trimmers for grass, as a rule, are equipped with universal heads with a diameter of the cutting cord from 2.5 to 4.0 mm.

Advice! Experts recommend using string heads equipped with ball bearings, as they have an increased service life, while reducing the wear of incoming components. At the same time, for replacement, it is best to choose the bobbin of the manufacturer indicated in the operating guide for the grass for the grass, which in turn will allow you to correctly install the head on its drive.

Manual bobbins

A manual mowing head is a coil in which the cutting cord during wear is stretched by the owner of a trimmer for the grass on its own. To do this, turn off the tool, remove the head and with the help of hands stretch the fishing line for a trimmer to the required length. However, despite some inconvenience, this type of head is considered the most reliable.

Forest winding algorithm

The type, thickness and length of the mowing fishing line are selected depending on the model of the trimmer for the grass. The diameter of the cord can be from 1.2 to 4 mm. It is easy to guess that the thicker you are refueling the cord, the tougher and thicker it can be cut.

There are 3 ways to find out what kind of fishing diameter you can use on your mower.

  • Contact the instructions of the device for information about the thickness of the cord.
  • Look at the coil itself. It can be marked with information about the possible diameters of the mowing fishing line.
  • Insert a trimmer fishing line into a socket. If it passes into it easily, you can use a cord of this diameter.

The fishing line for a trimmer is wound on a coil located in a mowing head. Therefore, it first needs to be opened (this was discussed above). There are two ways to wind the cord.

The first way

To correctly determine how many meters of fishing line is necessary for a specific coil, it is necessary to wind it on the reel so that the coil does not exceed the diameter of the boards. If the fishing line for a trimmer goes beyond the edges of the coil, you cannot insert it into the lid. As soon as you have decided on the length of the material, you need to load it into a reel, so do the following.

  • It is necessary to fold a fishing line for a trimmer in half, so one end is 10-15 cm longer than the other.
  • Please note that the coil is divided into 2 parts by the central side, with which charging begins. Find a recess on it and insert a cord into it, bent in half, with a slight effort.
  • This is very important to determine in which direction the fishing line for the trimmer is wound to the coil. If you look carefully, you can find an arrow on the drum or an inscription with an arrow indicating in which direction to wind. There are cases when there is no arrow on the coil. In this situation, you can look at the drawn arrow on the mowing head and wind the cord in the opposite direction.
  • The winding should be carried out carefully, wrapped with a reel, with maximum thread tension.
  • After the cord is finished, you must first fix the short end of the mowing fishing line, inserting it into the groove of the corresponding diameter on the side of the coil.
  • The other end, genuine, is installed in the groove on the opposite side of the coil.
  • After fixing the spit line, cut its ends, leaving the allowances about 10 cm.
  • Next, it is necessary to install an aged coil in a mowing head. To do this, insert and stretch the threads into the heads of the head, insert the coil into the housing, and then, applying the required force, pull the fishing line for a trimmer from the fasteners and tighten it.
  • Now you can put on the lid and fix it with latches.

Read how to remove the coil from the lawn mower of an electric house

The second method

Some coils provide the second method of fixing the cord: instead of one folded in half, you can charge 2 pieces of thread for a trimmer is replaced in accordance with the following algorithm.

remove, trimmer, cover, grass, fishing, line
  • Before replacing or loading a new thread in a coil, determine how many meters are required, as described above.
  • Bend one end of the cord in the form of a hook.
  • Find the hole in the bottom of the coil to fix the fishing line for the trimmer, and insert the end of the thread bent into the loop.
  • It is necessary to wind the cord in accordance with the direction of the arrow to the desired level not exceeding the diameter of the coil.
  • Do the same for the second coil nest.
  • The assembly of the head is no different from the method that was provided for when refueling the coil considered with a double piece of fishing line.

There is a very simple and fast way to replace a fishing line for a trimmer without disassembling a mower that you can see by watching this video.

The ends of the cord protruding from the holes in the case can be cut to the required length when the part is installed in the trimmer. There are two ways to do this:

  • The inclusion of a trimmer for grass (during rotation, the ends of the fishing line will be trimmed around a knife fixed for this on a protective cover);
  • Cutting the extra ends with scissors so that they do not touch the body.

The second method is used if you need to put on a large diameter cord, and the cutter cannot shorten it.

If the thread is tucked on the mowing head, but the length of the protruding ends of the cord is insufficient, they must be lengthened before starting the machine. This applies to the head with manual adjustment. However, there are cases when a semi-automatic mower is used, when, due to the insufficient length of the protruding ends of the cord, they do not automatically lengthen. In this case, you need to turn off the unit (absolutely necessary to pull the fork out of the outlet on the electric device), manually press the button located at the bottom of the part, and pull out a little fishing fishing line for the trimmer. After this procedure, the cord will be able to again lengthen due to centrifugal force if you set the maximum speed of spindle rotation.

Which line for a trimmer to choose

Before you stock up on this material for refueling in a trimmer for grass, you need to decide on the choice. After all, the usual so.called round fishing line for a trimmer is far from the only existing look. How to choose the most suitable? First you need to determine the working conditions.

Type choice. a line for a trimmer with a round section is the most common. It will suit any reels with the rarest exceptions. This type of consumable is suitable in order to mow fresh, juicy grass. But with the mowing of the so.called dryness, this kind may not cope anymore. It is pointless to mention attempts to mow shrubs and mention.

In addition to the usual type, there are others with sharp faces. Usually they are made by a “star” or “square”. The presence of sharp faces is the main feature and key difference between these threads.

It is thanks to this feature, the threads of such species are able to mow dry weeds. But the spicy threads are not devoid of disadvantages, the main of which can be called rapid wear and strength, markedly inferior to the round type.

In addition to the already mentioned types of forests, there are still interesting and often encountered varieties. Especially among them can be noted fishing lines, inside which a metal wire is stretched. Threads of this type are often used in tools working on gasoline and having an engine more powerful than one and a half horsepower.

Threads with a metal core are both with a round section and with sharp faces. Regardless of the type of cross section, such threads are the best suited to overcome hard.to.stop plants. Threads related to this type easily mow not only dry grass, but even small shrubs.

The threads with wire inside are favorably different from other types of consumables for their incredible wear resistance. But unfortunately, this feature has a more than noticeable effect on the price of this type. The cost of threads with a core significantly exceeds the cost of threads of other types.

Choice in thickness

In addition, special attention should be paid to the thickness of the consumption material. For mowing young grass, a thread is suitable with a diameter of one and a half millimeters. The larger the diameter of the thread, the more dry and rude weeds it can overpower.

When choosing a fishing line in thickness, there is one “but”. It is important not only to evaluate the capabilities of the material, but also to take into account the features of the trimmer for the grass. You must definitely look into the user’s management, which is attached to the tool, and find information about the requirements for the cutting element.

The use of inappropriate thread can lead to the failure of the tool. The use of too thick thread will entail the overload of the device engine. And the use of too thin thread will significantly increase the wear of the torque.

That is why it is necessary to approach the choice of consumables no less responsibly than to refuel in a trimmer for grass. When a suitable fishing line for a trimmer is found and purchased, you can begin to consider the ways to wind it on the coil.

Is it possible to make a coil for a trimmer for the grass with your own hands

On sale there are a large number of trimmer heads (not automatic), which have a low price and good quality. But sometimes situations arise, for example, in the country, when the trimmer coil broke, and its repair is impossible, the store is far away, and you need to mow. In this case, you can quickly, literally in a few minutes, make a simple trimmer nozzle to fix the fishing line from ordinary plywood 10-12 mm thick.

  • Take a piece of plywood or textolite and draw a circle with a diameter of about 14 cm on it.
  • Cut the disk with a jigsaw or hacksaw for metal.
  • Drill a hole in the center of the disk, suitable in diameter to the gear shaft. Do not forget before installing a disk on the shaft, put a puck on it.
  • You can fasten small corners along the edges of the disk or make 1-2 holes on the opposite sides. They will serve for refueling fishing lines in them.
  • To fix the fishing line for a trimmer, you can screw several screws into the plywood.

Such a homemade mowing nozzle is fixed on the shaft with a nut. Twist or unscrew the nut without fixing the shaft will not work. To replace the cord, it will be enough to release the screws, insert a segment of the fishing line of the required length and press it again.

Also, a mowing nozzle for fixing the fishing line on it can be made from a metal sheet. How to do this can be understood from the next video.

Replacing the fishing line with a disk or knife

When ennobleing a personal plot, park zones and other places where various plants are required, it is often necessary to change the cutting tool in the trimmer. This is dictated by the fact that the standard cord installed in a mowing head can only cope with herbs. But when a shrub or young growth of trees appears on the path of an employee, a fishing line for a trimmer cannot cope with such a task, and it requires a change to a more effective cutting tool.

Manufacturers of trimmers provided such situations, and complemented their products with a mass of nozzles in the form of knives with several “petals” or in the form of disks similar to circular saws.

If you replace a fishing line for a trimmer with a knife with several “petals”, then such a tool can be mowed by both high grass and plants with thick and dry stems. And changing the fishing line for the trimmer to the disk, the user of motorcycles has the opportunity to cut shrubs or small trees.

Knives and discs are installed according to the following algorithm.

    The first thing you need to remove, stagnating the shaft, a mowing head (twist clockwise) or a nut with anthers if the unit has not yet been used.

For a better understanding of the process of changing the tool, you can watch this video.

Problems with fishing line

Trimmeres users, both gasoline and electric, sometimes have problems with the cord. “Advanced” Kosilov owners can easily cope with the difficulties, realizing why this is happening, and for beginners, this is a problem that does not have a rational explanation. But in fact, everything is solved quite simply. The most common problems that happen to the fishing line are the following.

Cords of cord

If a trimmer fishing line is often torn, this can cause the following reasons:

  • Stones, small branches and other hard obstacles come across the grass;
  • The user mows the grass back to the fence, and if he is mesh, then this breaks the “antennae” even faster;
  • poor quality of the cord (it is recommended to purchase high.quality);
  • The output holes are worn out in a mowing head, which is why the fishing line for a trimmer is erased on the sharp edges of the bushings and breaks off (a complete replacement of the part will be required).

Large cord consumption

Basically, the cord quickly ends if you often knock on the ground with a semi.automatic head or press it hard. The coil unlock occurs, and the fishing line for the trimmer, lengthening, is cut off with a knife. Another reason that the cord quickly ends is the improper operation of the device with an automatic head: the user during kosbe often drops engine speed. But as we recall, the automatic head is arranged so that it is with each reduction in the revolution that a new portion of fishing line is supplied, so it is quickly consumed.

The thread does not hold

It happens that the thread is unwound if the spring weakened in the semi.automatic head. The fishing line for the trimmer is constantly extended and cut off with a knife installed on the casing, which increases its consumption. To check this, remove the casing and turn on the unit. If the fishing line for the trimmer “climbed”, then you will need to replace the spring.

a fishing line for a trimmer flies out

The reason that the cord after starting the unit is unwound is also a weakening of the spring inside the head. In addition, there are times when when the unit is turned on, a spitter head is scattered, and the spring installed in it is lost. Inexperienced users do not notice the absence of a spring and collect this node without it. Therefore, the cord does not hold, and under the influence of centrifugal force flies out.

The cord is not served, the coil does not spin

Automatic or semi.automatic head should serve a fishing line for a trimmer without stopping the unit. But if it does not come out, then the reasons may be as follows:

  • The fishing line for a trimmer in a coil is incorrectly wound, which is why the latter does not spin;
  • The cord is wound unevenly, and the thread can get stuck between the turns (the thread should be wrapped neatly, the turn to the turns, without distortions);
  • Too short ends of the threads come out of the holes, as a result of which there is not enough centrifugal force to extract them, and the fishing line is not supplied for the trimmer (it is recommended to always adjust the length of the cord before starting the unit, slightly pulling it up);
  • The fishing line for the trimmer is sticking together (it will be considered later).

The thread sticks together

This nuisance occurs most often due to the use of poor-quality cord. When the apparatus is operating, the head of the trimmer for the grass heats up, and a poor.quality fishing line for a trimmer in it melts, gluing among themselves. Also, sintering of the threads occurs when a fishing line with a solid obstacle occurs. In this case, there is a sharp braking of the cord, after which it drags it into the head, where it bothers. Some unit owners recommend lubricating the cord with mineral oil or spray on it with a silicone spray after winding on a spul. Others advise to wrap less threads on the coil. But it is better to immediately buy a quality product, in the manufacture of which the manufacturer took into account the factor of overheating of the head, and the thread will not stick together.

| Denial of responsibility | Contacts |RSS