How to remove a trimmer head from an electrimmer

Warranty production of the factory refueling of a trimmer for the grass will be in demand for fishing line substitutions. Having a very approximate idea of ​​how to fill the fishing line for a trimmer to the coil of a trimmer for grass without the help of others, the new ones without hunting take up this matter. How to wrap a fishing line for a trimmer to a trimmer coil for the grass, how to season a fishing line for a trimmer to a trimmer coil for grass. Autocut for a trimmer for STIHL FS 55 grass refueling the fishing line in a trimmer coil for grass 2 part winding of the fishing line on. But with some abilities, the development of this simple science does not represent any difficulties, and the similar annotation presented below will greatly facilitate this process.

In fact, there is no difference what kind of scythe you use, if it is electric or gasoline. The reference of the thread is carried out the same. The difference is only that if a gasoline braid for grass is used, you get more freedom, since you are not limited by the cable that is present on the electric spit

Yes, do not hesitate to use special videos for installing or refueling fishing line in an electric car, which can teach you much faster than a simple reading.

The first way

To correctly determine how many meters of the fishing line are required for a specific coil, it is necessary to wind it on the bobbin so that the skein does not exceed the diameter of the sides. If the fishing line for the trimmer will look out beyond the edges of the coil, you cannot insert it into the casing. After you have decided on the length of the material, it must be tucked in a bastard, so do the following.

It is necessary to fold the fishing line for double so that one end is 10-15 cm longer from the other. Please note that the bobbin is divided into 2 parts by the central side, from which charging begins

Find a groove on it and insert a cord into it, bent twice, putting a slight effort. It is very important to determine in which direction the fishing line for the trimmer is wound on the coil if you look closely, then you can find an arrow on the bobbin or an inscription with an arrow indicating which direction the winding should be carried out. There are times when there is no arrow on the coil

In such a situation, you can look at the arrow drawn on a mowing head, and wind the cord in the opposite direction. Winding should be carried out carefully, a turn to the turn, with maximum thread tension. After laying the cord is completed, you will need to fix it first the short end of the fishing line, inserting it into the groove suitable in diameter on the side of the coil. The second end, the one that is more authentic, is attached into the groove on the opposite side of the squash. After fixing the fishing line, cut its ends, leaving the allowances about 10 cm. Next, it is necessary to install a refueling coil in a mowing head. To do this, alternately inserting and pulling the thread into the weekends of the head, place the bobbin in the casing, after which, by applying the required force, pull the fishing line for a trimmer from the fixing grooves and tighten it. Now you can put on the lid and fix it with the help of latches.

Option

In this version, the head is twisted onto the gear shaft. To remove it, you need to fix this shaft. To do this, in such trimmers, for example, in the Huter and Champion devices, a hole is provided through which you can insert either a thin screwdriver or a metal rod.

So, to remove the bobbin, take 2 simple steps.

  • Insert the screwdriver into the hole and stall the shaft.
  • Take the head of the head and start twist it clockwise. It should be twisted in this direction for the reason that the thread cut on the shaft is left.

Review for the trimmer head Champion C5074 HT21

A trimmer head is a typical consumable for modern motorized cos (electrios or benzo, does not matter). Sooner or later, any user of such garden technology will be required. I have been working with various types of braids for more than 10 years and therefore I chose the head based on my experience of their operation. The product from Champion C5074 HT21 seemed to me quite solid and was acquired after checking compliance with the required parameters for my lawn mower.

A two-cord semiautomatic head in a cardboard-plastic blister is supplied. He is strong and colorful.

On the back of the package, the manufacturer and importer are indicated, requirements for the permissible diameter of the cord (2-3 mm).

Detailed instructions for replacing it and a list of compatible cobblestones from other manufacturers are given.

The product is made of relatively strong and viscous shockproof plastic. Pretty fat. The glossy appearance is a little confusing (I had one glossy head from Ebonite and did not even serve the season. The case scattered in a collision with a sharp stone). Head diameter 117 mm, height 73 mm. This is more than the average parameters for such products. Weight in the equipment of the manufacturer is 0.28 kg (2.5 m of fishing line with a diameter of 2.4 mm). On the working side of the head is the Auto.Oddachi button of the cord. Spring.Loaded medium, not tough. Quite rational adjustment for the economical consumption of fishing line and comfortable work.

A hole for stealing the head on the shaft of the gearbox was made on the reverse side. Left thread M10 by 1.25. The depth of the hole for the shaft of the braid for the grass is large (therefore, on the list are dozens of compatible models of KOSTA).

The release of the cord from the case is reinforced with metal embedded a non.Ferrous metal alloy with a smooth blockage. That’s right, they will not rust and spare/save fishing line for a trimmer from cliffs. The guides of the cord are installed tightly and their replacement during wear is not provided for.

I know from experience that the main drawback of this type of case is the protruding elements of the lock locks. Good speeds of a strict obstacle (stone, reinforcement and similar) they simply fail. Sometimes not immediately, but even then the damaged head remains to live not for long. On my spit, my native heads are deprived of this drawback. The locks have hidden latches and does not protrude nothing around the perimeter. The survivability of such a solution is fundamentally higher, but inside are made worse and refuel them one torment.

See also  What is better benzo or trimmer electric for the grass

The same head is thought out sensible and replacement/winding of the cord is much more comfortable. The case is easily disassembled. You need to remove the lid by pressing on the tongues of locks. Then remove/stretch the remains of the fishing line from the guide holes and then the bobbin will gently push out of the body with the inner spring.

It is tightly installed in a plastic sleeve (glass) and does not spontaneously fall out when analyzing the head. The normal decision that saves nerves and time (on some models when removing the lid, the spring strives to shoot and look for it later. ). In the picture below, note that the case has double walls and is reinforced with stiffness ribs. A competent solution that extinguishes the energy of external strokes and takes a bobbin from jamming.

After refueling the bobbin with a new cord, its tails must be threaded into special grooves of the bobbin. And then the ends of the fishing line are fixed and the wound the cord does not strive to unwind back, which allows you to calmly pass them into the brass holes of the case and insert the bastard into the body without fuss.

Made thoughtfully, re.Renewing the head is convenient. Here I will note another drawback. A small bobbin designed by the manufacturer for winding only 2.5 meters of the cord. On other types of heads I wrap 5-7 meters (here the thickness and profile of fishing line also plays a role). But this is relatively, because the replacement of the cord is not troublesome.

As a result, the Champion C5074 HT21 head is good for everyone, except for an unsuccessful solution of the lock locks and a small reserve of the cord. The price for such a product is very humane and change the broken one for a new one is not costly. Who has the lawns are even and clean and there is no need to climb into the boulets/landfills, it will serve for a long time. After all, the general quality of the materials used and manufacturing is quite at the level of serious equipment.

Instructions

In order to change the fishing line for the trimmer, it is necessary to extract the old one (if it was).

The coil is part of the design of the trimmer for the grass, which is located inside the head of the motorcosa, drum or bobbin. Depending on the manufacturers of the head can be different. But this article discusses only Patriot, although their mechanism is used by many other companies.

Now you need to understand how to properly remove the head from a trimmer for grass and how to get a drum out of it.

Champion Straight Shaft 2-Stroke Gas String Trimmer (Overview 100682)

Eliminate the malfunctions of the automatic coil with a fishing rod for a lawn mower

Instructions on how to promote a hand head on a trimmer is described below.

  • First of all, you need to clean the head of dirt and adhering grass if it is contaminated. To do this, you need to raise a motorcycle head up and, holding the casing, remove a special protective cover dressed on the drum.
  • The next step needs to remove the reel from the drum. The coil is easily removed even with one hand, because it is not fixed inside the drum.
  • The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with a coil, while twist the screw counterclockwise.
  • Now you can pull the coil out. As mentioned above, it is not fixed in anything except a hook with a metal shaft, so it does not need to be torn off with force. Neatly, in a circular movement you should pull the coil from the drum.
  • Now it remains to extract an old fishing line for a trimmer and follow the following instructions.

Installation of the coil and drum in its former place is performed according to the opposite algorithm.

Before the process of refueling the fishing line, it is worth making sure that the thread suitable for a trimmer was bought. In the case when the thread is not suitable, the fuel or energy consumption increases, as well as the load on the motor motor.

In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m fishing line. A specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the coil itself. If it is not possible to accurately determine the length, it can be done as follows: insert and wind the thread to such a state that the coil is completely charged (the level of the fishing line will be compared with protrusions in the sides of the coil). It is necessary to ensure that the fishing line for the trimmer sits in the coil exactly.

remove, champion, head, grass, trimmers

Do not forget that the thick thread will be shorter than thin.

The instructions for refueling the fishing line in the coil is described below.

The prepared thread must be taken and turned in half. It should be ensured that one edge is longer than the other by 0.1-0.15 m. Now you need to take the ends in different hands. The one that is smaller must be pulled to more, so that it becomes 2 times shorter. When bending, the indentation should be maintained at 0.15m. Find the slot inside the coil partition. Carefully prick the loop that turned out earlier in this slot. To continue work, it is necessary to determine the direction of winding the thread in the coil. To do this, just examine the coil. There should be an arrow on it. If the gunner could not be found, it is quite possible that there is a written designation. An example is given in the photo below. It is necessary to inspect the head of the coil. It has a direction indicator. However, this is the direction of the coil movement. To get the direction of winding, you need to wind in the opposite direction. Now you need to season the reel with a fishing line

It is worth noting that there are special guide grooves inside the coil. When wrapping a thread, you need to follow these grooves, otherwise you can damage a trimmer for grass

See also  How to remove a trimmer's traction for STIHL grass. Dismantling and assembly STIHL MS 180

At this stage, you need to charge the coil very carefully. When the user winds up almost the entire thread, you should take the short end (do not forget about the protrusion of 0.15m) and stretch it into the hole located in the coil wall. Now you need to repeat this action similarly with another end (on the other hand). Put the coil itself in the coil head, before that, extinguishing a fishing line for a trimmer through the holes inside the drum. Now is the time to return the drum to your place. After that, you need to take with both hands by the ends of the fishing line and pull them to the sides. Then you need to put the lid in place (here you can safely make efforts until a characteristic click is heard). Remained to perform “cosmetic work”. You need to see if the thread has come out too long. You can start a trimmer for the grass and check in practice whether everything is comfortable. If the thread came out a little long, you can cut it with scissors.

Self.Manufacture of bobbin

Quite often, a trimmer for grass is operated in the distance from places where you can purchase spare parts for a spitt with its breakdown. In this case, instead of a broken mechanism, you can install a simple coil made in design made by yourself. To do this, you need a sheet of plywood (textolite, metal, etc.), eyes, screws or screws. The process includes several stages.

  • A disk is cut out of the plywood sheet, which corresponds to the failed spool with a diameter.
  • A hole is drilled in the center of the disk, which matches the diameter with a shaft of a trimmer for grass.
  • Small eyes are attached to the opposite sides of the disk, which will serve to refuel the fishing line.
  • Through the eyes, pass the fishing line for the trimmer and fix it with ordinary screws or screws. The coil is ready for work.
  • Clutching the made bobbin between the two washers, it is attached to the shaft of the trimmer for the grass with a nut.

To replace the fishing line on a home.Made bobin, you will have to release fixing screws, insert a new section of the string and tighten the fasteners again. It is not necessary to remove the coil from the shaft of the trimmer for grass, however, it is necessary to exclude the possibility of spontaneous launch of the motor.

So, above was step.By.Step with the pictures described methods of repairing the string head. As you can see, the process is not complicated. And most of the breakdowns are directly related to the inaccurate refueling of the string and its unsatisfactory quality. You can clearly see all the stages of the process on the video.

Review for the trimmer head Champion C5074 HT21

A trimmer head is a typical consumable for modern motorized cos (electrios or benzo, does not matter). Sooner or later, any user of such garden technology will be required. I have been working with various types of braids for more than 10 years and therefore I chose the head based on my experience of their operation. The product from Champion C5074 HT21 seemed to me quite solid and was acquired after checking compliance with the required parameters for my lawn mower.

A two-cord semiautomatic head in a cardboard-plastic blister is supplied. He is strong and colorful.

On the back of the package, the manufacturer and importer are indicated, requirements for the permissible diameter of the cord (2-3 mm).

Detailed instructions for replacing it and a list of compatible cobblestones from other manufacturers are given.

The product is made of relatively strong and viscous shockproof plastic. Pretty fat. The glossy appearance is a little confusing (I had one glossy head from Ebonite and did not even serve the season. The case scattered in a collision with a sharp stone). Head diameter 117 mm, height 73 mm. This is more than the average parameters for such products. Weight in the equipment of the manufacturer is 0.28 kg (2.5 m of fishing line with a diameter of 2.4 mm). On the working side of the head is the Auto.Oddachi button of the cord. Spring.Loaded medium, not tough. Quite rational adjustment for the economical consumption of fishing line and comfortable work.

A hole for the reduction of the head on the shaft of the gearbox was made on the reverse side. Left thread M10 by 1.25. The depth of the hole for the shaft of the braid for the grass is large (therefore, in the list are dozens of compatible models of KOSTA).

The release of the cord from the case is reinforced with metal embedded a non.Ferrous metal alloy with a smooth blockage. That’s right, they will not rust and spare/save fishing line for a trimmer from cliffs. The guides of the cord are installed tightly and their replacement during wear is not provided for.

I know from experience that the main drawback of this type of case is the protruding elements of the lock locks. Good speeds of a strict obstacle (stone, reinforcement and similar) they simply fail. Sometimes not immediately, but even then the damaged head remains to live not for long. On my spit, my native heads are deprived of this drawback. The locks have hidden latches and does not protrude nothing around the perimeter. The survivability of such a solution is fundamentally higher, but inside are made worse and refuel them one torment.

The same head is thought out sensible and replacement/winding of the cord is much more comfortable. The case is easily disassembled. You need to remove the lid by pressing on the tongues of locks. Then remove/stretch the remains of the fishing line from the guide holes and then the bobbin will gently push out of the body with the inner spring.

It is tightly installed in a plastic sleeve (glass) and does not spontaneously fall out when analyzing the head. The normal decision that saves nerves and time (on some models when removing the lid, the spring strives to shoot and look for it later. ). In the picture below, note that the case has double walls and is reinforced with stiffness ribs. A competent solution that extinguishes the energy of external strokes and takes a bobbin from jamming.

After refueling the bobbin with a new cord, its tails must be threaded into special grooves of the bobbin. And then the ends of the fishing line are fixed and the wound the cord does not strive to unwind back, which allows you to calmly pass them into the brass holes of the case and insert the bastard into the body without fuss.

Made thoughtfully, re.Renewing the head is convenient. Here I will note another drawback. A small bobbin designed by the manufacturer for winding only 2.5 meters of the cord. On other types of heads I wrap 5-7 meters (here the thickness and profile of fishing line also plays a role). But this is relatively, because the replacement of the cord is not troublesome.

See also  How to remove the chuck from a Bosch electric screwdriver

As a result, the Champion C5074 HT21 head is good for everyone, except for an unsuccessful solution of the lock locks and a small reserve of the cord. The price for such a product is very humane and change the broken one for a new one is not costly. Who has the lawns are even and clean and there is no need to climb into the boulets/landfills, it will serve for a long time. After all, the general quality of the materials used and manufacturing is quite at the level of serious equipment.

Trimmer coil device for grass

The heads of mowing for trimmers are available in many performances. Both simple and complex. The figure below shows a semi.Automatic trimmer head from a mowing station dismantled Husqvarna (Husqvarna).

This type of head is present in the configuration of most gas braids and electric trimmers, such as Stihl (subsided), Patriot (Patriot), Champion (Champion), Bosch (Bosch), Huter (Huter) and others. The head of the mower is quite simple. It consists of the following details:

  • Mow the base of the head;
  • Button for semi.Automatic cord supply;
  • Coil (coil), which is filled with fishing line;
  • Spring;
  • Eyes. A fishing line for a trimmer comes out through them;
  • Trimmer head cover for grass;
  • Trimmer fishing line (cord).

The following photographs also show the simpler heads of the trimmer for the grass.

All these nozzles do not allow you to change the length of the mowing fishing line in semi.Automatic mode (after pressing the button). In the case of a break in the cord, the lawn mower must be stopped and manually replaced.

Lugus device: engine

The power unit is in most cases (for domestic use) a two.Stroke internal combustion engine operating on the fuel mixture of oil and gasoline. The power of the motor offered today by the household motorcycle market lies in the range from 0.5-0.8 liters.S (horsepower) up to 2-2.5

An important characteristic of the engine in the device of the lawn mower is the volume of its cylinder. It is on this value that the productivity of mowing work will depend

Замена лески на мотокосе.

The greater the volume of the engine, the higher the cutting speed and, accordingly, the faster you can dig up the given area. Typically, for standard mowing, the power unit is enough, the volume of the cylinder of which is approximately 30-40 cubic cm cm.

The launch system in the device of the lawn mower can consist of a large number of elements (their number and functionality depends on the branded developments of each company producing the tool), but among them the main ones are the inclusion button (1), the starting cable (2), the carburetor damper (3) and Pump (4) fuel pumping (primer). There are 2 types of launching a lawn mower. With an unfinished engine and with warmed. In the first case, it is necessary to transfer the button to the Start position, the damper is “closed” to the position, pump fuel 3-5 times 3-5 times, after which you can stretch the starter’s cord, making sharp and quick hand movements until the engine earned. Then it is necessary to transfer the damper to the “open” position and you can proceed to work. Starting a hot engine does not require manipulations with a primer and a damper.

In the device of the lawn mower, the engine is the main element that generates the energy necessary for the rotation of the working body.

Design features

It must be emphasized that the cutting head for a trimmer for grass contains special arrows. They allow you to make rotational movements of the coils in different directions. If there is a need to wind the fishing line for the trimmer towards rotation of the shaft, it turns into a specific position.

If, after the impact, the cord is not wound an automatic head, then its previous winding is made erroneously. In other words, after the head for a trimmer for the grass was installed, the user did not pull the ends of the fishing line from the grooves. Another nasty moment with a beard of grass may be sintering the coil turns.

For different models of trimmers, an automatic head consisting of 2 parts is used. Corps and bursting. Both elements contain springs. The 2nd part can be produced in several versions:

  • Single.Section. Both parts of the fishing line are wound up;
  • Two.Sectional. Each end is wound on a certain part; This type is more effective, because the fishing line for the trimmer is not confused and does not sinter.

There is a common and cheap method to re.Cross a single.Sectioned spool into a two.Section. A strong plate is useful for this. It is necessary to cut out a circle from it, the dialect of which should be equal to the thickness of the buffet. With all this, thickness is taken near the place where the fishing line for the trimmer is wound.

How to flash_.Trimmer_golovka_

One of the common devices created for cutting grass is a trimmer. Managing and serving it pain simply. That’s why it became popular in the middle of the population. Its significant advantage is its small weight. Even a child can cope with such equipment.

One of the all.Fought devices intended for haircuts of grass is a trimmer for grass. Managing and serving it pain simply. That’s why it became popular in the middle of the population. Its significant advantage is its small weight. Even a child can cope with such equipment.

Mowing head for a trimmer for grass

This is a special assembly coil with a snout cord. Its sizes may change. On the inside of the coil should be wound a 15-meter cord. Its end is stretched over a certain distance to do the work. When meeting with a tough object, it is destroyed. Trammer for grass is a coaching head in different designs. Everything is dependent on the type of device. They differ not only in design, and the connection method. There is also a universal head of a trimmer for grass, which is suitable for various equipment. This became probable thanks to a special adapter.

The chairman for a trimmer for grass is systematized in coordination with the method of feeding:

| Denial of responsibility | Contacts |RSS