replace, coil, trimmer, methods, repair

How to remove a coil from an electric trimmer for grass

There is a type of coils, in which the automatic mechanism performs winding without the help of others. It is quite only to correctly season the fishing line for the trimmer from the user. How to refuel a fishing line for a trimmer to a trimmer coil for grass? Video instruction. How to remove a coil from a trimmer for grass? How to wind a fishing line for a trimmer in in order to refuel a fishing line for a trimmer. The fishing line for the trimmer is passed through the hole on the inside of the case, its antennae without winding are tied through the hole on the outer case, the bobbin is assembled, and when rotating the winding button for the trimmer, the snitches are wound without the help of others. It is unrealistic to make the winding erroneous in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

Warranty production of the factory refueling of a trimmer for grass will inevitably require replacement of fishing line. Having a very approximate idea of ​​how to fill the fishing line for a trimmer to the coil of the trimmer for the grass on their own, beginners are reluctant to take this matter. However, with some skills, the development of this simple science does not represent any difficulties, and the presented instruction below will facilitate this process as much as possible.

The main malfunctions of the coil

Users of the electrimmer and lawn mower often face a problem associated with a semi.Automatic braid head. Coil malfunctions can be as follows:

The fishing line for the trimmer does not extend automatically

If, with a light blow, the trimmer coil button for grass on the ground is not lengthened for a trimmer, then the reasons for this may be the following.

Option 1. There was a snack, t.E. Squeezing the cord between turns. This problem usually appears if the user wound a fishing line for a trimmer to the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the fishing line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, even turns with good tension.

Option 2. Too short ends protrude from the head. A fishing line for a trimmer may not exit when hitting the ground, if its ends sticking out of the head, insufficient length (short). In this case, the centrifugal force is not enough for the fishing line for the trimmer to stretch. Therefore, it is required to stop the unit (drown out the engine or turn off the ethletric trimmer for grass from the network) and pull the fishing line for the trimmer manually, after pressing the button.

Option 3. A fishing line for a trimmer was soldered inside a mowing head. This leads to the fact that the coil is stopped and does not spin when the button is pressed. Basically, this happens for several reasons: poor quality of the cord, overheating of the coil with prolonged operation of the unit, a fishing line on solid items.

  • In the first case, the cord of third.Party manufacturers can be made of low.Quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
  • But, if you still purchased a fishing line for a trimmer of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after refueling the cord, moisten it either with silicone grease (from the spray can), or mineral oil). This procedure greatly reduces the likelihood of soldering a fishing line among themselves.
  • Also, a fishing line for a trimmer can sleep if during a mowing it hit a hard object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open a trimmer coil for grass and rewind a fishing line for a trimmer.

The cord spontaneously lengthens

There are situations when a user of a trimmer for grass notices a very fast fishing line consumption. At the same time, he never hit the ground with a button to lengthen the fishing line. The reason that the fishing line for a trimmer spontaneously lengthens, cutting off a special knife on the casing of the device, may be the absence of a spring in a mowing head. Often beginner users of mowers, trying to charge a fishing line for a trimmer into a coil, forget to install a clamping spring in the head, or completely lose it when opening the lid, and in the future, they do not even suspect its existence.

See also  What are the discs for a trimmer for grass. Description

Also, a fishing line for a trimmer can lengthen without using a button if the spring is weakened. If the spring check confirmed this fact, then it is necessary to put several goals under it to strengthen its clamping properties.

How to replace a coil on a trimmer?

Removing a coil on a trimmer to replace it may seem a difficult task. At first glance, this is really difficult, as you should adhere to accuracy and accuracy. The article tells how to quickly and has a sound replacing the problematic part.

Before removing the coil, the trimmer for the grass is jammed (if it is on gasoline) or turns off the network (if we have its electric version). Then step by step performs such actions.

  • Remove the cap that holds the spring.
  • Acting by force on the latch with one hand, and the other carefully remove the tire.
  • Connect the hole in the gearbox cup with the hole in the shaft hub (this action is performed very carefully).
  • Put the shaft into the gearbox hole with a key with 6 faces (without turning it at the same time).
  • Remove the bobbin.
  • To unscrew the screw.
  • Holding the body of the disassembled element with one hand, unscrew it with the second hand (counterclockwise).
  • With light swaying movements to remove the mowing head.

The assembly of a trimmer for the grass is carried out by the same actions in the reverse order.

All work needs to be carried out, adhering to the elementary safety rules and the following recommendations:

  • Jam the gearbox with a hexagon (if not, a regular screwdriver is used);
  • Jamming is mandatory, otherwise the shaft will turn around;
  • During the repair, the features of the tool are taken into account (paying special attention to the type of thread);
  • To make it more convenient to work with the unit, it must be turned down the engine and placed on a horizontally located surface;
  • Before dismantling a new coil, it is necessary to clean the tool;
  • The new detail should have the same parameters as the old;
  • If you neglect the previous requirement and install the part from another device, the trimmer for the grass will work incorrectly;
  • On the gearbox of most trimmers in the advantage of the left thread;
  • After the end of the work, you need to remove the screwdriver, which was immobilized the unit;
  • All work is carried out extremely carefully: the part is made of easily damaged plastic;
  • No need to tightly tighten the newly installed element, otherwise it will not be possible to remove it if necessary.

As you can see, there is nothing complicated in replacing the coil of the trimmer for the grass. It is necessary to strictly follow the instructions and carefully carry out all the work.

How to replace a coil on a trimmer?

Removing a coil on a trimmer to replace it may seem a difficult task. At first glance, this is really difficult, as you should adhere to accuracy and accuracy. The article tells how to quickly and has a sound replacing the problematic part.

Before removing the coil, the trimmer for the grass is jammed (if it is on gasoline) or turns off the network (if we have its electric version). Then step by step performs such actions.

replace, coil, trimmer, methods, repair

  • Remove the cap that holds the spring.
  • Acting by force on the latch with one hand, and the other carefully remove the tire.
  • Connect the hole in the gearbox cup with the hole in the shaft hub (this action is performed very carefully).
  • Put the shaft into the gearbox hole with a key with 6 faces (without turning it at the same time).
  • Remove the bobbin.
  • To unscrew the screw.
  • Holding the body of the disassembled element with one hand, unscrew it with the second hand (counterclockwise).
  • With light swaying movements to remove the mowing head.

The assembly of a trimmer for the grass is carried out by the same actions in the reverse order.

DIY: How to replace ignition coil and spark plug to a grass trimmer NAC

replace, coil, trimmer, methods, repair

All work needs to be carried out, adhering to the elementary safety rules and the following recommendations:

Replacing a Weed Eater String (String Trimmer Line) | The Home Depot

  • Jam the gearbox with a hexagon (if not, a regular screwdriver is used);
  • Jamming is mandatory, otherwise the shaft will turn around;
  • During the repair, the features of the tool are taken into account (paying special attention to the type of thread);
  • To make it more convenient to work with the unit, it must be turned down the engine and placed on a horizontally located surface;
  • Before dismantling a new coil, it is necessary to clean the tool;
  • The new detail should have the same parameters as the old;
  • If you neglect the previous requirement and install the part from another device, the trimmer for the grass will work incorrectly;
  • On the gearbox of most trimmers in the advantage of the left thread;
  • After the end of the work, you need to remove the screwdriver, which was immobilized the unit;
  • All work is carried out extremely carefully: the part is made of easily damaged plastic;
  • No need to tightly tighten the newly installed element, otherwise it will not be possible to remove it if necessary.

As you can see, there is nothing complicated in replacing the coil of the trimmer for the grass. It is necessary to strictly follow the instructions and carefully carry out all the work.

The main malfunctions of the coil

Users of the electrimmer and lawn mower often face a problem associated with a semi.Automatic braid head. Coil malfunctions can be as follows:

See also  How much oil is needed in a trimmer for grass. How to dilute gasoline with oil for chainsaws and trimmers properly.

The fishing line for the trimmer does not extend automatically

If, with a light blow, the trimmer coil button for grass on the ground is not lengthened for a trimmer, then the reasons for this may be the following.

Option 1. There was a snack, t.E. Squeezing the cord between turns. This problem usually appears if the user wound a fishing line for a trimmer to the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the fishing line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, even turns with good tension.

Option 2. Too short ends protrude from the head. A fishing line for a trimmer may not exit when hitting the ground, if its ends sticking out of the head, insufficient length (short). In this case, the centrifugal force is not enough for the fishing line for the trimmer to stretch. Therefore, it is required to stop the unit (drown out the engine or turn off the ethletric trimmer for grass from the network) and pull the fishing line for the trimmer manually, after pressing the button.

Option 3. A fishing line for a trimmer was soldered inside a mowing head. This leads to the fact that the coil is stopped and does not spin when the button is pressed. Basically, this happens for several reasons: poor quality of the cord, overheating of the coil with prolonged operation of the unit, a fishing line on solid items.

  • In the first case, the cord of third.Party manufacturers can be made of low.Quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
  • But, if you still purchased a fishing line for a trimmer of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after refueling the cord, moisten it either with silicone grease (from the spray can), or mineral oil). This procedure greatly reduces the likelihood of soldering a fishing line among themselves.
  • Also, a fishing line for a trimmer can sleep if during a mowing it hit a hard object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open a trimmer coil for grass and rewind a fishing line for a trimmer.

The cord spontaneously lengthens

There are situations when a user of a trimmer for grass notices a very fast fishing line consumption. At the same time, he never hit the ground with a button to lengthen the fishing line. The reason that the fishing line for a trimmer spontaneously lengthens, cutting off a special knife on the casing of the device, may be the absence of a spring in a mowing head. Often beginner users of mowers, trying to charge a fishing line for a trimmer into a coil, forget to install a clamping spring in the head, or completely lose it when opening the lid, and in the future, they do not even suspect its existence.

How to remove the coil and replace the fishing line for the trimmer

The owners of the trimmers, mainly beginners, confuse, bordering on panic, when it becomes necessary to change the cutting tool or fishing line for a trimmer in a reel. Very often, when trying to unscrew the mowing head, users simply make it unusable, not suspecting that it is unscrewed in the opposite direction. So that this does not happen, if you need to replace the tool, it is recommended to familiarize yourself with the step.By.Step instructions given later.

  • Before refueling the fishing line for the trimmer to the coil, drown out the engine of motorcycles or de.Energize the ethletric trimmer for the grass to avoid injuries that may occur in case of accidental rotation of the cutting tool.
  • Unscrew the nozzle mounted on the gearbox shaft. To do this, the shaft must be fixed by combining holes on the puck and on the axis, and inserting a metal rod or screwdriver into them.
  • Unscrew the nozzle. You should know that the thread on the shaft is left. Therefore, to twist the coil of the trimmer for the grass should be right, that is, clockwise.
  • Disassemble the mowing head. Most often, the head cover is attached to the fixers. To remove it, you need to drown these latches into the case, pressing the edges of the lid. If your trimmer has a semi.Automatic mowing head, which has a button from below, then disassembling the nozzle should be done carefully, since you can lose a spring that sometimes flies away when removing the cover.
  • Cut the required amount of fishing line. Usually its length is 5 meters. Use the cord of the diameter that is indicated in the instructions for the tool. It is not recommended to exceed the maximum diameter of the fishing line, since this will lead to increased load on the engine and greater consumption of gasoline.
  • Find the middle of the segment of the cord, folding it in half. You will get a loop.
  • Special grooves are cut out inside the coil (there may be holes). Insert the loop from the fishing line into this groove.
  • Wind a fishing line for a trimmer to a coil, turning it counterclockwise. You need to refuel the cord as evenly as possible, the turns should be laid without ceiling and with good tension. When the winding is finished, leave the free ends of the fishing line about 20 cm long and fix them in the grooves located on the sides of the coil.
  • Collect the braid head. Before you finally collect the nozzle, do not forget to insert a spring and washer (if it is available). Install the coil in the case, and prone the ends of the cord through the holes or eye.
  • Dress the lid and fix it with latches.
  • Screw the nozzle back to the gear shaft, also fixing it with a screwdriver. Tighten the coil of the trimmer for the grass will need to go to the left (against h. Arrows).
See also  STIHL fs 38 weed trimmer carburetor adjustment

How to wind a fishing line for a trimmer to a trimmer coil for grass video

This video tutorial shows in detail how to wrap a new fishing line for a trimmer on a trimmer or a motorcycle. For convenience, unscrew the mowing head. For clarity and convenience. Remove in the direction with a given arrow. First open the head. There are latches on the sides here. There are 2 of them. You can take it off with your hands, but if it does not give in, use the screwdriver. The design consists of 2 parts. Head, spring on which the winding of the fishing line is performed. Lid. Some of the button are inserted separately.

If we talk about the principle of work, there is nothing complicated here. The lid has clamps. The coil in the assembled position is pressed by a spring. Fixators do not allow to turn. Click on the button, the coil is slightly lifted, turned to several revolutions or by half a turn, the fishing line for the trimmer is fed out. Release the button. The coil is again fixed until you need to release a new fishing line for a trimmer again.

As for the choice of fishing line diameter. On some coils, information is written. There is a hole for fishing line with a diameter of 1.6 mm, 3-3.3. 2 or more millimeters. If the information is not indicated, determine the maximum permissible diameter, taking the head and extending the fishing line for the trimmer to the final opening

Pay attention to the instructions for the operation of a trimmer for grass

Two methods are used in the coil sample. In the side, which divides it into two parts, a slot was done until the end. Put a fishing line for a trimmer in it. We determine the required amount by wound on one of the parts of the coil. The length should not go beyond. In this case, a piece of about 4 m of fishing line with a diameter of 3 mm is required. Smaller diameter will need more.

Fold the cut piece in two. We release one end a little longer-10-15 cm. Bend more. We find a slot on the coil and start a loop there. A very important point. There is a Wind Line inscription. The direction of winding is indicated. If this is not found, then look at the arrow indicated on the mowing head and wrap the fishing line for the trimmer in the opposite direction.

Continuation on the video “Hotsem” from the fifth minute.

Owners of private houses know how necessary the type of tool is such as a trimmer for grass. It can be gasoline and electric, and they differ in the design of power units. For injection of grass in areas where there are stones, trees and other obstructing objects, a fishing line for a trimmer is used as a cutting device. This consumable in the process of use wears out, so how to wind the coil of a trimmer for grass, we will consider in detail in the material.

Typically, the process of replacing fishing line on a trimmer of a particular model is popularly described by accompanying documentation. Another question is that this documentation is often supplied in a foreign language, since the notorious lawn mowers for the most part are imported products.

Meanwhile, there is a much simpler, more economical and healthy way for human health and nature. Putting the lawns of an ordinary peasant oblique in order. Blory of braids for grass:

Which is subsequently accompanied by abundantly growing greens, and not by the formation of dryness as a result of the work of a trimmer for grass.

Brief briefing

Zetsila. Publications of materials interesting and useful for society. News of technologies, research, world.Class experiments. Social multimetical information. Media.

Useful videos

In this section you will find videos on which the owners of electrimmers show how to independently remove a coil or rogue from it, as well as change a fishing line for a trimmer for them.

Part of the devices on these videos are equipped with gasoline motors, but the methodology for removing/installing the coil and replacing the fishing line the same as on electric cos.

DIY head replacement on the Bosch electritrimmer:

How to remove the head and replace the fishing line for the trimmer on the BlackDecker GL716:

How to remove the drum with a fishing line using the example of the Huter Get-600 model:

How to remove and change the nozzle with a fishing line (Babin) in the Ryobi device:

| Denial of responsibility | Contacts |RSS