How to start a stihl chainsaw correctly

When working with the latest chainsaw STIHL, not required a running.In the aggregate! The fuel mixture is prepared in a ratio of 1:50, this means that for 1 liter of AI-92 gasoline will you need 20 ml of STIHL oil.

Step 1 of 15: Activate the chain brake

Before starting the chainsaw, activate the chain brake. To do this, squeeze the chain brake forward (Washing Machine. Illustration).

Before starting the chainsaw, be sure to remove the tire protection.

Step 3 of 15: pump up gasoline with a fuel pump (if any)

If the chainsaw is armed with a decompression valve, click on it. This will facilitate the process of starting a chainsaw.

Step 4 of 15: pump up gasoline with a fuel pump (if any)

If the chainsaw is armed with a fuel pump, pump up gasoline into the carburetor. This will facilitate the process of starting the motor.

Step 5 out of 15: Install a combined lever to a cool start position

Install the combined lever to the position of cool start. To do this, first activate the gas lever and the gas lever itself, and then translate the combined lever to the end.

Step 6 out of 15: Install a chainsaw on an open surface

Before starting, install a chainsaw on an open surface. The cutting headset should not come into contact with the surface, you will subject yourself to an excessive threat, and the headset may swell when starting.

Step 7 out of 15: Get the chainsaw with both hands

Get a chainsaw lying on the ground with both hands. With all this, the left hand should be placed on the handle, and the right. On the trigger. Step on your right leg to the back handle. So you will ensure the stability of the chainsaw.

Slowly pull the launch cable with the right hand until the tangible resistance appears. After that, pull the cable with force a couple of times so that the engine starts (by the ability to pull up so that the cable does not rub on the fan body).

Step 9 out of 15: the engine starts. Transfer the lever to the position of the half.Gas

The engine starts only at the Kutser time, and then turns off again. Open the throttle, translating the combined lever up to one fixation position (to the position of half.Gas).

Step 10 of 15: re.Activate the starting cable or pull

Re.Pull the starting cable, so that the engine starts again.

Step 11 of 15: click on the gas lever with an index finger

After the engine starts and starts to work, briefly press the index finger on the gas lever. With all this, the combined lever will move to the idle position.

Step 12 of 15: Raise the chainsaw from the ground

Slowly raise the chainsaw from the ground, with all this try not to touch the gas lever.

How to start a stihl ms 250 chainsaw

Step 13 of 15: deactivate the chain brake

Then release the chain brake, with your left hand pulling the chain brake handle over yourself. With all this, the left hand should remain on the handle. The corresponding click means that the chain is unlocked and can move along the tire.

Step 14 of 15: checking the chain lubricant system

Before starting work, be sure to check the chain lubrication system. To do this, place the saw on a light background (for example, a stump or a sheet of paper laid out on the ground) and give a full gas. If oil spots appear on a light background, this means that the chain lubrication system works fine and you can start work.

Chainsaw is ready for operation. Safety regulations when working with a chainsaw Washing Machine. In the operating manual.

How to start a chainsaw: how to properly start Stihl (Stihl MS-180)

The chainsaws are slightly different in structural features, but in most cases the assembly principle is carried out according to two standard schemes. Many devices contain information about the need to activate the emergency installation brake before starting the inclusion procedure. You should first master the installation of the plant and study the main methods of correcting breakdowns, then a person will have the opportunity to fully operate the device. The article will talk about how to start a chainsaw.

start, stihl, chainsaw, correctly

Briefly about the starting device

A chainsaw works on an internal combustion engine. This is a simple device, the design of which has no special bells. It usually works properly even in difficult conditions for this.

The functioning is provided by structural elements:

  • Carburetor engine (see. Carburetor adjustment).
  • Clipers of centrifugal type clutch.
  • Ignition system, in almost all devices contactless.
  • Carburetor that adds air to the fuel mixture.
  • Fuel system. Its standard device consists of a hose, filter and gas tank, but sometimes it also has additional details.
  • Starter.
  • Tire.
  • Chain (see. Oil for the chain).
  • Tension mechanism and circuit brake (see. How to sharpen a chain).

Step-by-step instruction

With an activated brake, the assembly process occurs much slower, so everything is also safe and more comfortable to turn on the mechanism without the use of brake equipment.

If a person is not sure of his knowledge and accuracy, then the brake, on the contrary, needs to activate. With the right order of action, the device does not start, the mechanism will not make actions dangerous for a person.

1 diagram of the standard mechanism

  • Before you start a benzoil, it is necessary to make a damper that performs the adjustment lever, push it off down, compared with the optimal position. First you need to click on the button responsible for the gas supply. Only if this condition is met, it is possible normal movement of the damper to extreme stops from below. You need to simultaneously move the damper and hold the gas button. The gas is installed in a standard position, and the damper closes the carburetor, preparing the device for proper operation.
See also  How to stroke the wall with a perforator correctly. Corner grinding grinding

In our rating of chainsaws in quality, you will find all the chainsaws with the optimal price-quality ratio.

It will also help to make your choice in favor of a particular chainsaw brand our other article.

At the Russian.Made chainsaws. Low price with a fairly high quality.

2 Scheme of a standard mechanism. How to start a saw correctly

  • The ignition is turned on. To do this, you need to move to the right place the toggle switch or move the switch.
  • You usually have to press the pile of swing more than two times. Gasoline is poured into it, after which you will have to click on the device more than three times. Sometimes a chainsaw is not equipped with a primer, then you can skip this stage.

When the device stalls constantly, you need to systematically start it again (see. What to do when the chainsaw stalls when pressing gas). After some time, the motor will gain momentum and will be able to maintain active work without interruptions.

If you can’t turn on and start a chainsaw

Когда все действия выполняются согласно установленному порядку, а бензопила не начинает работу, значит есть сбои в ее механизме. Typically, the cause of this phenomenon is common and easily eliminated problems, such as the lack of spark, overlap fuel, clogging of the filter that passes the air. In order to start a chainsaw, you will have to find the reason and perform the necessary actions to eliminate it.

Only the correct actions should be carried out. If a person does not know what to do, there is no need to commit rash actions. It is forbidden to disassemble the device, especially carefully you need to handle the carburetor. You can not unscrew any screws on it, since if its device causes a breakdown, then it is impossible to fix a chainsaw without professional equipment.

The actions that need to be performed in strict order are listed. Only when moving from one event to another can you determine the exact cause of the malfunction and quickly eliminate it without damaging other details. The algorithm of actions performed in case of failure in the chainsaw institution:

  • First, let the device take a rest. This is especially true for the saw that were in operation recently. It is enough to wait for no more than 10 minutes, since during this time the mechanism will cool and in the absence of other breakdowns will easily start. Sometimes it happens that during the establishment a candle is poured at the device. If this unpleasant property has occurred, then it is enough to wait for a very small pause and repeat all the actions for the motor factory again.
  • The hull cover is unscrewed from the device for taking out the air filter. The process of the device is performed in the absence of it. Sometimes the reason for the lack of ignition is that the filter is contaminated. If the ignition occurs without it, then the reason lies in this. To eliminate these troubles, it is enough to wash the filter under running, warm water and soap, then dry out. You can also replace the old element with a new.
  • The spark plug is removed. The spark is checking. If it does not appear, you need to replace the old candle with a new. This usually helps and the spark appears, but in some cases there is no sparks when replacing the mixture.

Criteria for choosing motor oil

A full.Fledged alternative to recommended branded oils may be similar in working characteristics products of leading manufacturers. As a result of natural selection on unofficial ratings of consumer demand for many years, the motor and chain oils of the Stihl and Husqvarna trades.

  • It is strictly forbidden to use cheap analogues of unknown origin for the preparation of a combustible mixture for a chainsaw, as well as motor oils for mopeds and boat engines.
  • In order to avoid the risks of acquiring cheaper, but of poor.Quality falsifications, it is recommended to buy consumables in company and licensed trade enterprises.

The working mixture is prepared in a small amount sufficient to perform one.Time operation. For long-term use, more than one month, the combustible composition is not calculated due to significant deteriorations of the working characteristics.

The mixture through a fine.Mesh filter or suede is poured into a gas tank, from which the gas pipeline is supplied to the input of the carburetor.

Features of the first and subsequent launches

Learning to start a chainsaw in principle is not difficult. The necessary skills are acquired directly during operation.

The launch of the chainsaw is carried out by a cord starter, in most modern models combined with an inertial or spring light system. Properly adjusted mechanism reduces the effort required to start the engine, almost half.

Since it is impossible to start a chainsaw without a starter, to extend its resource, it is necessary to develop a smooth, with a slight acceleration, the jerk of the cord, which does not create large loads on the design of the starting device.

  • For the first launch, the tool filled with fuel and chain oil should be installed on an even base, unlock the system for preventing random launch and the emergency stop of the saw headset. If there is a primer, you should pump fuel into the carburetor.
  • To start the engine, you should install a gas drive for small revolutions and, holding the tool by the handle, pull the starter handle. Start a chainsaw for the first time, which is called from half a turn, most likely it will not work. Even a completely working and adjusted tool “grasps” from 3-4 attempts.
  • At the idle mode, the piston group and a connecting rod-crown node work in conditions of oil starvation, so the idle time of the idle must be limited to a minimum.

Step-by-step instruction

With an activated brake, the assembly process occurs much slower, so everything is also safe and more comfortable to turn on the mechanism without the use of brake equipment.

If a person is not sure of his knowledge and accuracy, then the brake, on the contrary, needs to activate. With the right order of action, the device does not start, the mechanism will not make actions dangerous for a person.

1 diagram of the standard mechanism

  • Before you start a benzoil, it is necessary to make a damper that performs the adjustment lever, push it off down, compared with the optimal position. First you need to click on the button responsible for the gas supply. Only if this condition is met, it is possible normal movement of the damper to extreme stops from below. You need to simultaneously move the damper and hold the gas button. The gas is installed in a standard position, and the damper closes the carburetor, preparing the device for proper operation.
See also  Snowcat with a motor from a chainsaw with their own hands

In our rating of chainsaws in quality, you will find all the chainsaws with the optimal price-quality ratio.

Stihl Chainsaw Model MS210C Won’t Start-Troubleshooting, Assembly, and General Information.

It will also help to make your choice in favor of a particular chainsaw brand our other article.

At the Russian.Made chainsaws. Low price with a fairly high quality.

2 Scheme of a standard mechanism. How to start a saw correctly

  • The ignition is turned on. To do this, you need to move to the right place the toggle switch or move the switch.
  • You usually have to press the pile of swing more than two times. Gasoline is poured into it, after which you will have to click on the device more than three times. Sometimes a chainsaw is not equipped with a primer, then you can skip this stage.

When the device stalls constantly, you need to systematically start it again (see. What to do when the chainsaw stalls when pressing gas). After some time, the motor will gain momentum and will be able to maintain active work without interruptions.

If the chain of the chainsaw is not lubricated.

During the operation of the chainsaw, friction is between the bus and the chain. In order to avoid premature wear, constant lubrication is needed for the chain mechanism. For this, a special pump is provided, which serves the lubricant dosed, taking into account the number of engine speeds.

If the device chain is not lubricated, then you need to look for the cause in the channel clogged with sawdust, or in the leak of the oil pipeline. In addition, in the area of ​​oil pumping fittings, the flow can also be observed. The channel is advisable to clean from time to time, as well as monitor the amount of oil in the tank, which will allow the operator to work with the tool for a long time.

Basil starts and stalls. Why?

There are several simple rules for the operation and maintenance of a chainsaw, compliance with which will allow the maximum to extend its service life. Preparation of the correct fuel mixture, regular filter cleaning and periodic replacement of parts for a long time will save you from the need to repair your tool. If the breakdown failed to avoid, then you can understand its reason completely independently. This applies to any grades of chainsaws, starting from the more complex models “Husqvarna” and “Stihl” and ending with the simplest models “Makita” and “Patriot”.

The chainsaw immediately stalls

What to do if the chainsaw is stalling immediately after starting? First you need to check the presence of fuel in the gas tank. If its level is not enough, then you need to prepare the fuel mixture in strict accordance with the ratio of gasoline and oil prescribed in the operating instructions. Gasoline should have the maximum possible octane number, and the necessary brand of oil, as a rule, is indicated in the technical passport of the chainsaw.

Next, check the light of the ignition, as well as the contact of its tip with a high.Voltage wire. The gap between them should be no more than 0.5 mm. If necessary, the candle is cleaned from the carbon and dried. It is recommended to occasionally change the candle to a completely new. The reasons that the tool stalls when you press gas, lies in the fuel filter or jacket of the carburetor. Cleaning the gasophiller will not take much time and effort, but it is better to entrust the disassembly and cleaning of the carburetor to the specialists of the service center.

My Stihl chainsaw won’t start!!! Step by step diagnoses and how to repair

Babble stalls at idle

There are common cases when a chainsaw stalls at idle speeds. First of all, you need to check the silencer, and, in the case of its contamination, clean the exhaust sorrow of exhaust. Also on carburetors of some models and others. There are bolts with inscriptions H and L. Respectively, gross and accurate setting. Having adjusted the bolt of L during the operation of the chainsaw so that its speed increases (to crank the bolt by half a turn), it is possible to eliminate this problem. The adjustment of the carburetor requires the mandatory presence of an electronic tachometer and is a rather time.Consuming process. That is why in such cases it is better to contact professionals.

Basil stalls at load

If the chainsaw stalls at the load, then the cause of this can be a fuel system or a contaminated air filter. Fuel replacement in compliance with the correct proportion of gasoline/oil or cleaning of the air filter. Universal solutions of such a problem. Incorrectly cooked mixture of low.Quality gasoline and, for example, machine oil, is the main reason for the faulty operation of the chainsaw, including in the case when it heats up and stalls.

Basil stalls when tilted

With a horizontal position of the chainsaw, the fuel tube lies at the bottom of the gas tank, when the instrument is inclined, the tube is above the fuel mixture, t.E. In airspace. This is the reason that the chainsaw stalls on the side.

Basopile stalls at high speeds

In the event that the tool stalls at high speeds, you need to check three parts: air filter, fuel pump and gasoline filter. The air filter must be cleaned, you can even wash under water and dry well. Then it is enough to disconnect the fuel hose from the carburetor and see if the fuel flows from it or not. If it flows with a full stream, the gasoline filter can not be checked. If on the contrary, then the malfunction was found. The soundtress can be cleaned with an ordinary needle, and the filter is carefully disconnected from the suction hose, clean it or replace it with a new. The gasoline pump is checked for wear: if the fuel does not seep through it, then everything is in order with it. If the problem is that your tool stalls at full speed is due to some damage to the pump, then this part must simply be replaced with a new.

  • Blog
  • About the service center
  • Served brands
  • Diagnostics and repair prices
  • Delivery
  • Spare parts
  • Contacts

Repair and service of garden equipment.

Specialized Service Center “Agrotekervis”-comprehensive warranty and post-warranty services of garden and communal equipment of world manufacturers! We sell spare parts with delivery throughout Russia!

How to start a chainsaw of Stihl 180. A detailed instructions for launching

On all Stihl chainsaws, two.Stroke engines are installed, the cold launch of which has a similar algorithm. But there are models on which additional equipment is installed that allows you to start a saw without excessive efforts. For this reason, the algorithm for their start may vary slightly.

Let’s look at how to start a regular saw and how the process differs from the launch of a modified model.

Standing Stihl 180

In order to start the Stihl 180 chainsaw for cold, it is necessary to observe the algorithm indicated by the manufacturer in the instructions for the Stihl 180 chainsaw, namely:

  • Turn on the ignition and install the engine control lever in the lowest position (in this position, the airburator of the STIHL 180 carburetor cloth overlaps the air from the air filter, and the throttle is completely open, so the fuel mixture is enriched);
  • Pull the starter handle several times, until the first outbreak is passing (the flash signals that the fuel mixture entered the cylinder and the saw was ready to start);
  • Set the control lever to one position upward from the fully lowered (in this position the air damper opens, and the throttle remains in the same position as before);
  • Pull the starter and start. The saw will start and work at increased speeds, due to the fact that the throttle is open as possible. To install the damper in the idle mode, you need to press the gas trigger and immediately release, the tool immediately normalizes the momentum.
See also  What chain oil to use in a chainsaw

On the Stihl MS 180 chainsaw, any additional devices are not installed in the standard configuration capable of facilitating launch.

Below you can see how to get Stihl 180. The video reflects in detail all the main points, and the author’s Комментарии и мнения владельцев allow you to understand the whole process to the smallest detail.

Start Stihl MS 180 C

The device of this model, in comparison with the previous one, has some differences in the starting mechanism, but it does not bear any changes to the launch algorithm. The fact is that the Ergostart system is installed in STIHL 180 C, which, due to the additional spring installed in the chainsaw starter, reduces the engine resistance during starting.

Start Stihl MS 211 C-BE

The fuel supply system in the Stihl MS 211 C-BE chainsaw is additionally equipped with a manual fuel pump, which allows you to easier to start a chainsaw on a cold.

Instructions for the launch of this model of the Stihl chainsaw contains one additional item, which is that before starting the chainsaw to the cold, it is necessary to pump fuel into the carburetor using the pump. Further, the instruction does not differ from the launch of the Stihl 180 and passes the same algorithm.

start, stihl, chainsaw, correctly

What happens at the time of pumping fuel with a primer, and how it helps to get a saw more effectively?

At the time of starting a saw without a primer, several movements by the starter are carried out only so that the gasoline pump under the action of a pulse from the saw card, pumps fuel into the carburetor.

The pump installed in the fuel highway allows manually, without unnecessary movements by the starter, to pump gasoline into the carburetor. The effect of such an action is obvious, the saw will start much faster.

Many owners of the benzo tool, mistakenly believe that a manual pump can be unnecessarily pumping fuel into the carburetor and for this reason will flood the candle. It is fundamentally wrong, t. To. The system is capable of circulating. Excess gasoline from carburetor will be directed, according to a special hose intended for this, back to the tank.

There is no need to use a primer on a hot chainsaw, t. To. Fuel in the carburetor is enough to start starting.

How to start a chainsaw with a valve of decompression

Before you get a Stihl chainsaw on which a decompression valve is installed, it is necessary to enable it. I would like to note that there is no decompression valve on the STIHL 250 saw.

After the first outbreak passes, the valve will be installed in normal operation, respectively, after the engine control lever is installed in the open air damper and the launch continues, it is necessary to press the decompression valve again.

Schematically, valve operation is shown in the figure below.

In fact, the valve does not launch faster, it just simplifies the process and makes it more comfortable, t.To. For the launch, a person will have to apply much less effort.

A saw with a decompression valve, regardless of whether a cold engine or hot, must be started using a valve to relieve the force of turning the engine. This will significantly increase the service life of the starter and reduce the number of ragged laces, t. To. It is installed on chainsaws with a large volume of the cylinder and, accordingly, compression.

How to start a saw after prolonged downtime

I can not have a chainsaw, after prolonged downtime. Such Комментарии и мнения владельцев can be found on forums on the repair and operation of the saw. Let’s figure out how to start a chainsaw after prolonged downtime.

The fact is that about successful launch after downtime, you need to take care in advance and correctly prepare the saw for storage. According to the manufacturer’s instructions, before storing storage, it is necessary to drain the fuel from the tank, and then start the engine and make the fuel in the fuel system.

Do I need to run into a new chainsaw

Since it is during this process that the so.Called grinding of all motor details and a feather headset is produced.

Thus, through such a simple process, you can not only largely extend its life, but also increase the degree of its productivity. But you will get a good result only if you do everything right, without any violations.

You must remember that before starting the device, you need to carefully be carefully as they say from the crust to the crust to study the instructions for the operation of your chainsaw. And apply absolutely all the recommendations prescribed by the manufacturer regarding your safety in working with the device.

It is also important that the “heart” of the effective operation of your tool is precisely the oil. Since it is it that becomes a guarantor of the long operation of the chainsaw. To date, there are a huge amount of various oils that are made specifically for two.Stroke engines.

In fact, this kind of assistants are not expensive. Since in most cases expensive lubricants are used for motorcycles and mopeds. Therefore, it is somehow illogical to use chainsaws for engines, the main reason for this is the high price of oil.

It is also worth noting that the most common and, in fact, the best manufacturers of oils intended for chainsaws are: Huksvarn, Oregon, STIHL and Dolmar.

Since their products have peculiar additives, thanks to which, without a share of doubt, you can use chainsaws at any time of the year and thanks to which, by adding them to gasoline, uninterrupted and long operation of the engine itself is guaranteed.

| Denial of responsibility | Contacts |RSS