How to wind a fishing line for a trimmer to a trimmer coil for grass: Key points

Most of the problems associated with the fishing line are similar to different trimmers and are solved in a similar way.

Turning the string

  • The presence of solid objects in mowing grass: branches, stones, etc.D., contact with which the string breaks off;
  • Powder of grass is close to the fence, and if it is mesh, then the fishing line for the trimmer is torn even faster;
  • Low.Quality cord. It is necessary to replace with a new reliable consumable;
  • Wear of the output holes in the mowing head, as a result of which the fishing line for a trimmer breaks off from friction on the sharp edges of the bushings. It is required to replace parts with a new.

Large fishing line

Typically, a fishing line for a trimmer ends very quickly if you constantly knock a semi.Automatic coil on the ground or press it with an effort to the surface. In this case, the head is unlocked, the cord is lengthened, and the knife cuts it. The second version of the fast consumption of fishing line is a trimmer for grass with an automatic coil is incorrectly used. If the mower regularly lowers the engine speed, the string is constantly lengthened and cut and as a result is quickly consumed.

The string does not hold

If a spring weakens a semi.Automatic type in a semi.Automatic coil, a fishing line for a trimmer does not hold and unwinds when working. The cord is extended, cut off with a knife, as a result, the owner of the equipment notes that the thread quickly ends.

A fishing line for a trimmer flies out

If the string flies out with kosbe, this is another evidence that the spring in the bobbin is weakened or completely lost with an inaccurate analysis of the head. As a result, the cord does not hold and pops up when rotating.

The string is not advanced

In the coils of automatic and semi-automatic cords, the cord is served without stopping the trimmer for grass. If this does not happen, then:

The fishing line for a trimmer in the head is wound wrong, so the coil does not spin; The winding of the fishing line is made unevenly, so the cord stuck between the turns and does not go out. So that this does not happen, you need to wrap the thread carefully, preventing distortions, a turn to the turns; The ends of the cord emerging from the holes are very short, centrifugal force is not enough to extract them, so the fishing line is not served-before turning on the trimmer for the grass, it is important to control the length of the thread and slightly lengthen it, if necessary; The cord is stuck.

The coil does not spin

The reasons why the coil does not spin are similar to the lack of fishing line. This is the wrong or uneven winding of the string, its sticking, as well as the short ends of the cord, emerging from the holes.

Trimmer fishing line sticks together

If when working a fishing line for a trimmer sticks together, the main reason is the installation of a low.Quality cord. In the course of work, the coil is heated, and a poor.Quality string melts and glued. The second reason is the clash of the cord with solid objects. In this case, its sharp braking occurs, the thread is drawn into the head and picks up.

So, replacing a fishing line for a trimmer on a trimmer will not be difficult if you know how to disassemble the coil and wind the cord winding. This process is similar for technology of different brands. A detailed description can be found in the instrument operation instructions or watch on the video.

Choose a fishing line for a trimmer

So that you can correctly wind the string on a grass grinder, select the consumable of the proper quality and with suitable characteristics. The thicker the cord, the more difficult the tasks can be solved with its help. Most situations use a standard thread with d = 2 mm.

tighten, fishing, line, trimmer

If you do not know which diameter to choose for a mower, you can apply one of the ways:

  • Carefully consider the bobbin. Most popular manufacturers such as Husqvarna, Stihl, Daewoo, Champion, etc., indicate the parameters of the recommended consumables;
  • Read the instructions of the device;
  • In practice, try to place the string in the output hole. The material of the right diameter will pass into it freely.

There are several life hacks to select a thread for a grass grinder:

  • If the unit has an engine of less than 500 W, then it is worth using a thread with a thickness of not more than 1.3 mm.
  • The 2 mm cord is perfect for equipment with a power of 1 kW;
  • If you have a gasoline unit, pay attention to the shaft. Bent models are best compatible with a 2 mm format, 2.4 ≤ d ≤ 3 mm is suitable for direct.
  • The higher the power, the thicker the string should be.
  • Buy only high.Quality and durable branded consumables from the manufacturer of the unit. In professional stores of garden equipment, experienced sellers will help you buy consumables of the desired parameters.

How to refuel a fishing line for a trimmer to a trimmer for grass: a few simple tips

Thanks to modern power tools, a person is given a lot of opportunities to reduce manual labor. Such innovations include a trimmer for grass, which significantly facilitates the process of mowing of grass and the care of the lawn. This device reduces the time for garden work, turning complex physical labor into entertainment. As a cutting tool in a trimmer, a fishing line for a trimmer is used. It is strongly pulled and thus mows the grass of almost any height. It is easy to manage the power tool, but the problem arises when the cutting material ends. Not everyone will immediately figure out how to refuel a fishing line for a trimmer to a trimmer for grass. Although this is a simple operation, it is not always clear to a person who is faced with this task for the first time. Over, the instructions do not indicate information on how to choose and replace a trimmer fishing line for a trimmer.

When you figure out how to change the cutting material, further use and maintenance of the electrimmer will greatly simplify. To wind a fishing line for a trimmer for a trimmer for grass, several operations should be performed, namely:

  • Unscrew the nozzle, rotating the drum to the right. You will have a head in your hands with the remnants of an old thread. Open it with a screwdriver or squeeze the lock and turn the lid towards the arrow. This operation should be carried out carefully, since there is a spring inside, which, straightening, can throw away all the internal details of the drum. To change the fishing line for a trimmer in a trimmer, you need to get a coil and remove the remains of the material.
  • Take 5 meters of a new thread and fold it in half. In the middle of the coil there is a hole into which you need to insert the material. There is also an arrow indicating the direction to wind a fishing line for a trimmer for a trimmer for grass. It is important to take into account some points. If there are two holes in the coil, then half of the fishing line for a trimmer for the grass should be seasoned in one direction, and the second in the opposite. Ending to insert the material, it is better to leave 15-20 cm free.
  • Assemble a drum, install a spring and washer in place. After that, holding the coil, tie the ends of the fishing line in the holes on the sides of the nozzle. Then put the head in place, pulling the cutting material.

As a rule, you need to change a fishing line for a trimmer in a trimmer once over the entire season. However, if the area of ​​the mowing and the height of the grass is large, this consumable will have to be installed more often. If you need to refuel a fishing line for a trimmer in a trimmer for the grass “Makita” or another manufacturer, you can buy it in the online store “Toolparts”.

How to refuel a fishing line for a trimmer to a trimmer for grass: a few simple tips

Thanks to modern power tools, a person is given a lot of opportunities to reduce manual labor. Such innovations include a trimmer for grass, which significantly facilitates the process of mowing of grass and the care of the lawn. This device reduces the time for garden work, turning complex physical labor into entertainment. As a cutting tool in a trimmer, a fishing line for a trimmer is used. It is strongly pulled and thus mows the grass of almost any height. It is easy to manage the power tool, but the problem arises when the cutting material ends. Not everyone will immediately figure out how to refuel a fishing line for a trimmer to a trimmer for grass. Although this is a simple operation, it is not always clear to a person who is faced with this task for the first time. Over, the instructions do not indicate information on how to choose and replace a trimmer fishing line for a trimmer.

When you figure out how to change the cutting material, further use and maintenance of the electrimmer will greatly simplify. To wind a fishing line for a trimmer for a trimmer for grass, several operations should be performed, namely:

  • Unscrew the nozzle, rotating the drum to the right. You will have a head in your hands with the remnants of an old thread. Open it with a screwdriver or squeeze the lock and turn the lid towards the arrow. This operation should be carried out carefully, since there is a spring inside, which, straightening, can throw away all the internal details of the drum. To change the fishing line for a trimmer in a trimmer, you need to get a coil and remove the remains of the material.
  • Take 5 meters of a new thread and fold it in half. In the middle of the coil there is a hole into which you need to insert the material. There is also an arrow indicating the direction to wind a fishing line for a trimmer for a trimmer for grass. It is important to take into account some points. If there are two holes in the coil, then half of the fishing line for a trimmer for the grass should be seasoned in one direction, and the second in the opposite. Ending to insert the material, it is better to leave 15-20 cm free.
  • Assemble a drum, install a spring and washer in place. After that, holding the coil, tie the ends of the fishing line in the holes on the sides of the nozzle. Then put the head in place, pulling the cutting material.

As a rule, you need to change a fishing line for a trimmer in a trimmer once over the entire season. However, if the area of ​​the mowing and the height of the grass is large, this consumable will have to be installed more often. If you need to refuel a fishing line for a trimmer in a trimmer for the grass “Makita” or another manufacturer, you can buy it in the online store “Toolparts”.

Which line for trimmer is used for a trimmer for grass?

The type of cross section of the cutting thread should correspond to the vegetation that needs to be mowed.

If you need to change the fishing line for the trimmer, then you need to select specifically the type that is recommended by the manufacturer specifically this model of the trimmer for grass, in other words, the thickness of the cutting thread should be suitable for the power of the motor and the size of the unit.

It is better to choose a specialized cutting thread. It is worth soaking a fishing line for a trimmer for some time if you plan to change it in a coil.

After soaking, it acquires an elastic look and becomes stronger.

The cutting thread can be made of various components. Often found in the middle of them. Nylon.

This material is characterized by the highest degree of wear resistance, the ability to withstand different temperatures and the highest loads.

A fishing line for a nylon trimmer can be stored for a long time, it does not dry out and does not lose its hardness.

Therefore, its service life can be quite long.

Coils or heads for motorcycles have a different structure:

How to catch more fish?

  • One.Built. In the modification of such a trimmer for the grass there is only one working fishing line for a trimmer. Such an unit is used in the main thing for small work, such as the ending of the grass.
  • Two.String. Can be both automatic and automatic. Here the equipment includes two strings. Such a trimmer is used for herbs for mowing and clearing sites.

Instructions for the correct wound of the cutting thread on the coil of the trimmer for the grass:

First of all, you need to disassemble the head. To do this, click on the latch and turn the lid to the side

Measure the right amount of cutting thread and insert it into a slot.

Win a fishing line for a trimmer in the direction of the arrow on both sides. The ends of 15 cm long should be left not wound. These ends are inserted into opposite slots. Then the ends are fixed in the hole on the head.

Then the spool is carefully inserted into the case, for this you need to press it slightly on it.

If necessary, then you can pull the remaining ends of the thread outward. To do this, you need to pull one end of the thread first, and then the other so that they can easily pass through the slots on the head.

tighten, fishing, line, trimmer

Soaking Your Trimmer Line to Make it Last Longer

Now you should assemble the grooves on the case and tighten the lid.

Then press the spool and try to twist it all the way

If a click was heard, then the spool snapped. Next, you need to stretch the free ends of the thread to the end.

How to wind a fishing line for a trimmer to a mowing head of a trimmer for grass or motorcycle

The video shows in detail how to wind a fishing line for a trimmer to a trimmer coil for grass or motorcycle. The gas line is dressed.

Step-by-step instruction

Ready! The most difficult in the whole process. Wind a fishing line for a trimmer to a coil, as it constantly strives to slip out of her fingers.

In the end, I want to add that you should carefully take the choice of fishing thickness, which you will “refuel” into your trimmer for grass. I advise you to buy a fishing line for a trimmer thicker, then it will last longer and will wear more slowly.

Restring/rewind/gulung Grass Trimmer Line for Black Decker 530W

Nikita Khlintsov. Specialist in the garden technique of Foresta.

Posted by Decoratem. Updated 23 Jun 2021.

Change a fishing line for a trimmer on a trimmer

This article will be able to tell you how to change the fishing line for a trimmer on a trimmer. For some people, this work may not be simple. But step.By.Step instruction that is here will help you in this matter.

So, the first thing to do is remove the gearbox cover. Combine the hole on the side of the figure of the lower washer and axial seizure, insert the screwdriver to fix the shaft from the scroll. Now we unscrew the nozzle. The carvings on the shaft, as a rule, have a reverse cut, consider this when unscrewing.

Next, it follows the disassembly of the nozzle. There the lid is fixed with clamps through the holes. So you just need to second these latches in the holes, and the lid will be removed. If the nozzle has automatic \ semi.Automatic modes of fishing line, then there is a spring inside, which when opening the lid can just fly out, be prepared for this. We lay out all the removed parts carefully in order.

Now it’s time to take a fishing line for a trimmer and unwind 5 meters from it, cut off this piece. Pay attention to its thickness, do not wrap a fishing line for a trimmer of greater thickness on the unit than indicated in the guide to the tool. Otherwise, an increased load on the engine and a larger fuel consumption during operation will be obtained. We bend the measured fishing line for a trimmer in half to find the middle and get a loop.

In the middle of the coil there are a couple of recesses, sometimes these are not a recess, but the holes located opposite each other. We cling to one of the recesses and wrap a fishing line for a trimmer counterclockwise. If the coil has 2 compartments, then we wrap on them separately each end of the fishing line. Leave the last 15-20 cm free and pinch them while the coil is in the recesses.

Collect the device again, stretch the free ends of the fishing line in the holes on the case. We put the lid, clicking the latch into our grooves. Now you can stretch these free ends of the fishing line.

It remains only to attach the working unit in place, as in the first paragraph. Do not forget about the reverse rotation on fastening.

Now you were able to learn about how to wind a fishing line for a trimmer for a trimmer for grass. Actually, the whole process was described in detail above. No laborious operations requiring the presence of specialists. Your lawn mower is ready for work again.

Choose a fishing line for a trimmer

The fishing line for the trimmer should be strong, stiff and flexible. In the trimmer it serves as a working tool for cutting grass. Flacks of different thicknesses are made. From 1.2 mm to 4.0 mm. Most models are designed for the maximum thickness of the thread of 3 mm. What is the diameter of the fishing line for the grass for grass in one case or another depends on a number of factors.

Depending on the hardness of mowing vegetation:

It is important to consider that too thin thread accelerates the wear of the motor, too rough. Will accelerate its overheating and premature failure.

The structure of the cord of the fishing line matters:

  • Round. Universal, most durable, for rough grass;
  • Curly. For soft plants;
  • Twisted with notch. For thin long stems.

Important! Choose a fishing line for a trimmer of the type and parameters that the manufacturer Motokos recommends. Such material will work for a long time and efficiently with optimal loads on the product of the product.

Step.By.Step instructions on how to wind a fishing line for a trimmer to a trimmer coil for grass

With the advent of spring, you often spend your time in the country or personal plot. From such a problem as grass and weeds, you will be protected by a trimmer for grass. This tool without much difficulty trims and mows grass in complex areas, where this is not within the power of an ordinary lawn mower. Trimmer for grass. A very effective and convenient tool for mowing grass along fences, flower beds, houses and aisles in the garden. Several types of garden trimmer are invented (gasoline, electric and battery). It would seem that everything is fine, eats in your arsenal
tighten, fishing, line, trimmer

B is such a wonderful assistant, but over time the cutting element wears out and there is a need to replace the ended fishing line. And how to refuel a fishing line for a trimmer in a trimmer for grass, not everyone knows. We offer to use step.By.Step instructions with attached photos.

Instructions on how to wind a fishing line for a trimmer to a trimmer coil for grass

  • One. First you need to disassemble the head of the trimmer for the grass. Click on the latch on the product case and turn the lid clockwise. We extract a bobbin.
  • Now we have to figure out how to wind a fishing line for a trimmer to a trimmer coil for grass. We measure about 6-7m fishing line and insert its end into the hole.
  • We wrap a fishing line for a trimmer on both sides. The direction of winding is always indicated on the bend in the form of an arrow.
  • We leave free ends of the cutting element 15 cm long. Do not wrap too much fishing line. Leave 6 mm between the outer edge of the bobbin and the fishing line.
  • We insert the remaining two ends of the fishing line into the opposite holes.

In this article, we figured out how to wind a fishing line for a trimmer to a trimmer coil for grass. And if you did everything right, then when pressing and holding the bobbin, it should stretch out again. Trammer Lines for a trimmer for grass. A very important element without which the tool loses its functionality. In fact, this is the heart of a trimmer for grass. Therefore, make a purchase in a specialized store of garden equipment and approach the choice with special attention. When buying a new fishing line for a trimmer, be sure to compare it with a piece of the old used cutting element.

| Denial of responsibility | Contacts |RSS