Is it possible to dissolve the board with a end.Saw | How to dissolve the lining along

Many are interested in the question of how to dissolve the board, t.E. Make it cut along to obtain more thin blanks. Typically, such work uses a circular saw, which is designed for this type of work. But there are times when there is no circular saw at hand, but there is a end. And with the help of this tool it is also possible to dissolve the boards, but subject to some conditions.

Before you take up such a job, it should be understood that the main purpose of the end saw is still not a longitudinal cut, but a transverse or corner cut. Therefore, if you plan to carry out a large amount of work of such a plan, you should think about acquiring a tool more suitable for this. A circular saw, with which you can produce a longitudinal cut of boards of any length. See all the differences in the end of the end from the circular.

If necessary, the end saw is used in order to dissolve the boards, but this is necessary for this:

  • Your tool should be required and the function of horizontal drive movement, which provide the ability to operate the tool in two planes. We recommend that you look at the rating of end saws with a length;
  • For this type of work, a special saw disk is required, which will provide high.Quality and even longitudinal cut. Find out how to choose a disk for a end saw;
  • The board should be of small length, since the broach of the end saw has its own restrictions, and to work with the Big Dina boards, this tool will not work with all the desire. The maximum possible length of the workpieces depends on the model of the end saw.

How to use a end saw

When the saw is chosen, it must be configured. Then she will be ready for use. Should act according to the rules. And you need to figure out how to control the tool depending on the processed material.

On wood

A trigger switch is used for launch. But the tool will not start performing cuts until the lock lever is pressed. After that, the equipment is lowered to the material. Before work, it is recommended to put on protection products to protect yourself from chips that will appear when processing wood.

The wooden workpiece should be held with your hand if the cut occurs at right angles. But if the work is performed by a newcomer, it is recommended to use the clamp. It holds the material motionless, allowing you to focus on the cut. The clamp is necessarily needed if they work with blanks not at right angles, but at any other.

To adjust the cutting angle, it is necessary to use the platform reversal. It is necessary to unscrew the handle acting as a turning lock, and squeeze it down. The platform is ready to move.

Attention! When changing the angle, the sawing area increases. This reduces the convenience of using a saw, so it is necessary to use clamps.

To change the angle of cutting of wood, you can use the vertical inclination of the end. The fixation handle is first weakened, set the desired slope and fix it again.

For metal

Before turning on the tool, it is necessary to make sure that its nodes and the capabilities of the disk are free to move. To carry out the oblique saw, it is necessary to loosen the mounting screw at the rotary table and start turning it to the desired angle. The set position is immediately fixed. If the work is long, periodically, you should check how accurate the ending is. This is due to the fact that after some time there is a weakening of the mounting screw.

If you need to saw with the left inclination, then it must be configured correctly. The mounting screw of mounting the inclined angle is released and the desired angle is set. To fix the installed parameter, the screw is tight. After that they continue the saw.

Important! When the work is finished, after turning off the tool, you must wait for the cutting disk to completely stop. After that, the handle returns to the position up.

It is forbidden to remove a protective casing from the device. It rises when the disk is lowered down for the saw.

Miter saw

This instrument is also called a pendulum saw due to its characteristic design: the cutting disk sways with the electric motor over the base as a pendulum.

All pendulum saws are installed to work on the table, on a workbench or on the floor. For ease of work and greater stability, it is better to even attach the bed to the table using clamps or screws.

An electric motor with a saw disk can rotate over the bed in a special pendulum mechanism around three mutually perpendicular axes. The rotation angle is counted on the existing scales. Thanks to this, the saw can cut the blanks exactly from the given angle. For example, door platbands are cut off at an angle of 45 degrees for an even and beautiful connection “on the mustache”.

See also  How to sharpen a wood saw. How to properly sharpen a hacksaw with a file

Equally important in the carpentry craft so that the ends of the parts are strictly perpendicular. This operation is called ending and is performed just with the help of a end saw. “end”.

To make a comparison of two tools more visual, we made a table for you:

A circular saw Miter saw
Appointment Fast cutting of wooden details in any direction (straightforward) Finishing cutting wooden parts from a given angle
Requirements for the workplace The operator holds the tool in his hands The tool is installed on the surface of the table and t. P.
Limiting the size of the workpieces in length Not Not
Limiting the size of the workpieces in width Not There is, depending on the diameter of the working disk and the construction of the saw
The restriction of the depth was drunk There is, the maximum depth is limited by the diameter of the disk The maximum thickness of the workpieces is limited by the diameter of the disk
Sawing along the fibers Maybe In combined models
Sawing across the fibers Maybe Maybe
Sawing at an angle to the plane of the part Maybe Maybe
Sawing at a given angle Not Yes
Models with battery power There is Not
Yandex Market price from 2100 to 14100 From 3200 to 40,000

How to choose the right end

How to choose a end saw so that

Pallbearer. I Saw The End

Sellers. Consultants in the trading floor are aware of the products presented by him and the products. However, so that the purchase process does not turn into a monotonous monologue of the consultant and the depressed silence of the buyer, at the end of the model that takes with him twice as powerful and three times more expensive than it could actually arrange, the buyer needs to have a clear idea of ​​that,

  • Why did he need a saw;
  • What operations is he going to perform on it most often;
  • What are the maximum dimensions of the workpieces;
  • What amount of work per month is planned.

Clear answers to these questions, firstly, will inspire the consultant with minimal respect, and, secondly, will narrow the circle of the models in question to reasonable limits. But even within the framework of this narrowed list, the spread of and additional opportunities will be great. At this stage, the buyer will decide

  • Does he need a laser pointer (in fact, he always needs. The time of cut “by eye” passed.);
  • Do you need an electronic memory adjustment system;
  • Do you need a canal system?

If the end saw is bought for episodic work such as the manufacture of a frame for a greenhouse or gate in the garden. There is no need to go bankrupt to a high.Performance professional unit of a well.Known brand with an extended base, electronic setting, controlled by a length and other improvements.

Such a saw will be needed if the buyer plans to open his business on woodworking, already has a sufficient amount of orders of medium and high complexity. In this case, the professional device will save time and quickly pay off.

How to use a end saw

When the saw is chosen, it must be configured. Then she will be ready for use. Should act according to the rules. And you need to figure out how to control the tool depending on the processed material.

On wood

A trigger switch is used for launch. But the tool will not start performing cuts until the lock lever is pressed. After that, the equipment is lowered to the material. Before work, it is recommended to put on protection products to protect yourself from chips that will appear when processing wood.

The wooden workpiece should be held with your hand if the cut occurs at right angles. But if the work is performed by a newcomer, it is recommended to use the clamp. It holds the material motionless, allowing you to focus on the cut. The clamp is necessarily needed if they work with blanks not at right angles, but at any other.

Saw 5 Ending (Epic Quality)

To adjust the cutting angle, it is necessary to use the platform reversal. It is necessary to unscrew the handle acting as a turning lock, and squeeze it down. The platform is ready to move.

Attention! When changing the angle, the sawing area increases. This reduces the convenience of using a saw, so it is necessary to use clamps.

To change the angle of cutting of wood, you can use the vertical inclination of the end. The fixation handle is first weakened, set the desired slope and fix it again.

For metal

Before turning on the tool, it is necessary to make sure that its nodes and the capabilities of the disk are free to move. To carry out the oblique saw, it is necessary to loosen the mounting screw at the rotary table and start turning it to the desired angle. The set position is immediately fixed. If the work is long, periodically, you should check how accurate the ending is. This is due to the fact that after some time there is a weakening of the mounting screw.

If you need to saw with the left inclination, then it must be configured correctly. The mounting screw of mounting the inclined angle is released and the desired angle is set. To fix the installed parameter, the screw is tight. After that they continue the saw.

See also  Chopper of branches from a circular saw with his hands

Important! When the work is finished, after turning off the tool, you must wait for the cutting disk to completely stop. After that, the handle returns to the position up.

It is forbidden to remove a protective casing from the device. It rises when the disk is lowered down for the saw.

Power and number of revolutions

The power of end saws can vary depending on the model from 800 to 2500 watts. 1600–1800 watts are considered the golden middle. Instruments of just such power are most in demand today, because they do equally well with their task both in home workshops and in small production.

What gives us knowledge of the magnitude of such a parameter as power consumption? Firstly, the correct correlation of the power of the end saw and the structure of the processed material will avoid overload of the tool, which extends the time of its active operation.

Secondly, the larger the power of the saw, the greater the diameter of the disk that can be installed on it. As an example confirming this statement, we compare the two end saws from Bosch. On the PCM 7 model, whose power is 1100 watts, you should select a disk with a diameter of not more than 190 mm. But for GCM 10 J Professional with a capacity of 2000 watts, a disk with a diameter of 254 mm is suitable. It should be borne in mind that with an increase in the power of the saw and the external diameter of its disk, the dimensions and the weight of the tool increase. So, the first of the models given as an example weighs 9 kg, and the second is already 14.5 kg.

Another technical characteristic that is worth paying attention to when choosing a end saw is the number of revolutions of the saw disk. The value of this parameter lies in the range from 3200 to 6000 about./min. Pure and high.Quality cut (without chips of coating, delaying wood fibers, etc.D.) possible only when working at high speeds.

So, for example, with a 260 mm saw diameter, its angular velocity should be at least 2800 about./min. In expensive professional models, the angular speed, as a rule, is not lower than 4000-5000 about./min. Even with large disks diameters. A number of manufacturers offer end saws, the number of revolutions in which can be adjusted depending on the type of work performed at the moment.

How to use a end saw?

A carpenter often has to make angular transverse incisions on the boards. The cut should almost always be precise, since it forms an angular connection for a door cover, skirting board, paint frame or any other design, and a miscalculation can lead to an unsightly clearance. A tool for this work is a trim saw.

Miter’s saw is a tool that you need for the manufacture of corner transverse sections.

The simplest ending saw consists of a hand saw and an open box with pre.Chopped grooves for the direction of the saw, but the end saw is easier to use, faster and more precisely. This is mainly a cutting saw installed on a vertical spindle, which turns 45 degrees in any direction from the dead point. An integral end saw that you must consider when buying if you do not yet have a end saw, also rotates around the horizontal spindle and allows you to cut my bevels and sleeves.

Most power tools give better results after you have developed the ability to use them correctly, and an integral end saw is no exception. This will not take much time to develop this skill, practice with several pieces of wood, before cutting truly

Appreciate the power that you hold in your hands

Miter’s saw does not have the same freedom of movement as a circular saw, but it deserves the same respect. This can ruin your work if you do not hold it exactly during cutting, but it will also lead to a short work of your fingers if you do not take care of how you keep your job. Remember that the end saw is intended only for transverse incisions. Never try to make incisions. Follow these tips for safe use:

Keep your fingers at a distance of at least 6 inches from the blade to avoid injuries.

  • Operate the saw on a flat stable surface. Do not put it on the ground or on a shaky table. Make sure that the region is well lit and free from homeless wood and other garbage.
  • Make sure that all the protective equipment of the saw, including the protection of the blade, the engine brake and the rotary locks of the table and saw, is installed and works correctly.
  • With one hand, fix the work on the fence, and control the saw with the other hand. Never cut by hand. Keep your fingers at a distance of at least 6 inches from the blade.
  • Support the ends of long pieces of wood that hang over the saw table by more than half of their total length. This provides a cleaner cut and prevents fingers slip. Do not cut pieces of wood with a length of less than 8 inches.
  • Wear protective glasses to protect your eyes from split wood and sawdust.
  • Wait until the blade ceases to rotate before cleaning the wood from the table. Never touch the blade while it still rotates.

Hipples

Read the leadership of your owner. It contains a number of other tips and safety recommendations that you need to know before using your saw.

Cutting installers use the end saw for cutting angles at the ends of the skirting boards.

The cut at an angle can be defined as an angular incision made across the grains of wood. You can note the angle by drawing a fishing line for a trimmer on a piece of wood, or you can use the angular indicator on the table. The drawing of the line independently gives the most accurate results, because table sensors on all, except for the most expensive saws, as a rule, are disconnected by one or two degrees. However, when tilting the ends of wide boards, such as skirting boards, using the endow function, it is necessary to rely on the corner sensor.

  • Draw a fishing line for a tree using a bevel or ruler.
  • Put the tree on the table and press it to the fence. Comers the far end of the tag about the center of the open throat of the fence.
  • Loosen the table lock and turn the saw to the desired angle, then lower the blade and accurately adjust the angle in accordance with the direction of the line. Rightly tighten the lock. Adjust the wood so that the blade is next to it from the pruning side.
  • Raise the blade, press the trigger and wait until the blade reaches the maximum speed of rotation. Lower this hand and rotating blade down into the forest and continue to lower it until it drops on.
  • Let go of the trigger, raise the blade and wait until it stops rotating before taking off the firewood.
See also  How to saw with a wood hacksaw

Hipples

Do not start cutting until the blade reaches its full speed of rotation. If you start earlier, the blade can break a tree and spoil the delicate objects, such as moldings or skirting boards.

Using an integral end saw

The composite end saw allows you to simultaneously perform ends and mowing.

On an integral end saw, the adjustment of the bevel and ending does not depend on each other. You make a bevel, setting the saw angle on the horizontal axis on any angle, different from 90 degrees. Usually you have to rely on the manometer to set the angle due to the complexity of aligning the blade with the angle of inclination marked on the tree.


When performing an integral cut (in which pruning and chamfer are performed simultaneously), draw a fishing line for a trimmer for cutting at an angle, set the cutting angle, then set the angle of inclination. Adjust the part on the table so that the saw blade is as if on the cut side of the line, as with a perpendicular section, and then make a cut.

Some tips for safe and high.Quality sawing

Cutting with a end saw is quite simple, and as long as you draw clear lines, make accurate settings and follow the safety rules, it is easy to get excellent results. Some types of cuts are more problematic than others, and require special methods.

How else can you use the end saw

The presence of a end saw on the farm is a universal tool of a wide spectra, which can be made not only of corner, but also ordinary transverse cuts of various materials. The ending can replace the wood machine and the circular saw if necessary, and be used for longitudinal sawing of wood and other materials.

Most importantly, no matter what work you do with a end saw, it is very important at the same time equip it with a sawing disk suitable for this work. Despite the existence of universal multifunctional disks, such options will not give perfect cut results. This is due to the fact that for each material a disk with a certain number of teeth, a specific inclination angle and the type of sharpening are required.

Choosing a brand’s end saw

It is believed that some of the best manufacturers of endings is Metabo and Makita. Bosch and Hitachi have a circle of fans, as well as Encor and Dewalt. As clear, this list can be continued. Let us dwell on specific examples.

The vast majority of well.Known companies make it possible to expand the desktop already in the basic configuration. But sometimes, if you have to work with a larger part, you may need to use additional support. For example, the Makita LF 1000 saw has folding stands that simplify the workflow.

A reliable design of the ending is considered the one that has an aluminum or magnesium bed. Thanks to the use of these metals, not only strength and durability are achieved, but also the mobility of the tool, simply because it becomes easy. For example, Bosch GCM 10 has a weight of 15 kg.

The Hitachi C12LCH model is available with a unique digital indication system for the angles of the table rotation and tilting the cutting head, as a result, sawing becomes a high.Precision process and the time of preparatory work is reduced, which is important in the production conditions.

Supporters of domestic products evaluated the Bets power tool. The manufacturer gives 5 years of warranty for end saws.

Before you buy the tool, decide why you need it, how often you will use it and whether you are ready to sacrifice your mobility and ease in favor of power and more functions, which is characteristic of a professional tool. For all issues regarding how to choose a end saw, contact the consultant manager of our store. See the characteristics of models, compare and make the right choice.

| Denial of responsibility | Contacts |RSS