Heads Tails Channel Catfish

How to put a fishing line for a trimmer for a lawn mower

In order not to make a mistake with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the coil. This information is usually presented on a tip, which will not allow us to make a mistake using the appropriate equipment.

If the information on the coil about what diameter the fishing line for the trimmer can be refueled, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the equipment, it remains to figure out how to charge it. There are two ways for this, but not for all they are applicable. Consider both methods in details, and already depending on what models and trimmers you use, you are determined on your own which option is suitable.

It is interesting! The principle of how to wind a fishing line for a trimmer for a tip of motorcycles is appropriate not only for autonomous benzar groups, but also for electric trimmers.

Lifehack

When performing work using a network trimmer for grass, an extension cord is mandatory. After all, the indicator of the length of the standard wire in such soda technology is about 30-50 cm, which will be clearly not enough to perform daily tasks and mowing grass in a personal plot. In the case of an unreliable connection of the fork of the wires of garden equipment and a nest located on the extension cord, a sharp shutdown of the device is possible.

To solve this problem, most manufacturers, equip the design of their power tools with special mounts, which allow you to reliably fix the extension cord and exclude the possibility of breaking the contact between the device fork and a socket located located. On trimmers, such a mount is made in the form of a special hole with a hook, which is located on the back of the device handle. To fix the extension cord, it needs to be folded in half (that part of the wire on which the fork is located in half), and then stretch through the hole and put it on the hook.

The technical properties of the cord and the selection of diameter by the power of the trimmer for grass

If you take the packaging of the fishing line in your hands, then only two main parameters are indicated on it. This is the total length and cross section. Instructions on how to choose a fishing line for a trimmer for a trimmer for grass is not attached, so you have to find out from specialists. Finding a good specialist is not so simple, especially since every year not only new fishing lines, but also coils are produced every year.

The first thing to solve is the diameter, thickness or cross section of the cord. All this is one parameter characterizing the performance of work by trimmers, benzocouses, motorcycles and travo.Shirts. What sections to buy a fishing line for a trimmer for your trimmer for grass? In order not to make a mistake, you should take with you a segment of the old cord, and provide it to the seller. Based on the segment you provided, the seller will give a similar cross section the cord.

This option is certainly reliable, but it is impossible to call it correct. Why? After all, the choice of fishing line depends not only on the head used, but also on the power of the tool used. To begin with, it is recommended to solve what diameter the fishing line for the trimmer can be used on trimmers and benzocoses, depending on their power parameters:

  • Electric trimmers for grass with power indicator up to 500 W. Cords with a cross section of up to 1.6 mm are used. Such tools are designed to cut young grass in personalities
  • Gasoline and electrical units with power indicators from 500 to 1000 W. Involve the use of cords with a thickness of 2 to 2.4 mm. Such units with consumables are used to prick thin and thick grass, as well as weeds. In trimmers for grass up to 1 kW, you can install a fishing line for a trimmer with a diameter of 1-1.6 mm, but at the same time it will be quickly wear out
  • Trammers for grass and lawn mowers with power indicators over 1 kW. Allow the use of the cord with a thickness of 2.4 to 3.3 mm. Such fishing line can cut thick and dried stems, as well as thick thickets. If the consumable material with a thickness of more than 3 mm does not cope with the task of cutting grass, then metal disks with blades, teeth and knives are used

It is interesting!Manufacturers produce a trimmer fishing line for a trimmer with a diameter of more than 3.3 mm, only it is extremely rare, and exclusively on powerful gasoline units.

See also  Where can I get my petrol mower repaired?. Maintaining the cutting units of the lawnmower

The process of replacing the fishing line

For each trimmer, the manufacturer recommends a fishing line for a trimmer, or a cord, a certain diameter. A coil is made under it. It can be from 1.2 to 4 mm: you need to see according to the instructions what size of the fishing line is permissible for your tool. For example, many trimmers with the maximum value are 3 mm (recommended for hard grass). The thicker cord can not be installed.

A thin fishing line for a trimmer, 1.2. 1.6 mm, is suitable for mowing young, soft vegetation

Also, when choosing, pay attention to the structure of the cord: round is the most durable and suitable for rough grass, curly. For soft, twisted or with notch. For thin stems. Depending on what grass grows on the site. Lawn or wooden, buy appropriate consumables

It is important to know! Buy only a branded fishing line for a trimmer recommended by the manufacturer of a trimmer for grass

It is made of high.Quality materials and has strength. It will perfectly cut the grass and not wear out so quickly

It is important to know! Buy only a branded fishing line for a trimmer recommended by the manufacturer of a trimmer for grass. It is made of high.Quality materials and has strength. It will perfectly cut the grass and not wear out so quickly. Useful advice: place a segment of the cord in the water for 30 minutes, then it will become more elastic and stronger

wind, fishing, line, trimmer, lawn, mower

Useful advice: place a segment of the cord in the water for 30 minutes, then it will become more elastic and stronger.

How to replace string trimmer edger line

The fishing line for the trimmer is wound on the spool, which is hidden in the body of the trimmer head. To get to it, you need to disassemble the element. The housing is provided with latches-fixers, when clicking on them, the cover cover is easy to remove. Sometimes disassembly is carried out by promoting the body.

Be careful! Remember in what sequence the elements are installed, how a spring and a fixing screw are located inside the head. Gently fold all the details in one place so that nothing is lost and there are no problems during assembly.

Type of coil With a dividing side Without a dividing side
Fishing winding one. The prepared segment of the fishing line is folded in half and the bending place is clung to the groove in the dividing side. Some coils do not have such a groove, then the fishing line for the trimmer is cut into two parts and each of the segments is inserted into the upper and lower part, catching the ends into special holders. 2. Each end of the fishing line is placed in its gutter. 3. The coil is rotated so that the fishing line for the trimmer is wound in the direction of the movement indicated by the arrow. Both ends are wound in one direction. 4. The free ends of the fishing line 15. 20 cm long are temporarily placed in special holes on the rogue. They should be opposite to each other. The hole on the body is selected according to the diameter of the fishing line (next to it it usually says what diameter it is designed) one. The line of the fishing line is cut into two parts. 2. Next, it is necessary to fix the ends: they are inserted either into the holes in the upper part of the coil, or into special mounts on the video itself. 3. The winding is carried out in the direction indicated on the spray. Both segments lead to each other, preventing them from crossing. 4. Free ends are diluted on two opposite sides and if there are slots in the coil, they fix them there. The slot should correspond to the diameter of the fishing line

We offer to familiarize yourself: catching pikes on a wobbler. Simple rules

We described how to wind a fishing line for a trimmer into a coil of a trimmer for grass with two antennae. This is the most common option. But there are other ways. For example, if there is one antennae in the mowing head, then the winding is carried out without folding a fishing line for a trimmer. They rotate in the direction indicated on the corps of the spool, and the free end of the cord is temporarily fixed in the slot on the case.

Useful advice: act carefully when winding the fishing line, do not pull it so that it does not sit in the coil very tightly. It is necessary to ensure its free move for subsequent stretching.

After the fishing line for the trimmer is windplated on the spool, it is necessary to assemble the case. The coil is placed so that the ends of the fishing line can be pulled out at the weekend of the trimmer head. Slopes in the spool, where they were temporarily inserted, will not let them slip. If there are no such slots, hold the ends with your fingers when you place the coil in the body.

Which fishing line for a trimmer to choose to refuel a lawn mower

The thickness of the polyethylene thread depends on the model of the technique and varies from 1.2 to 4 mm. She may be:

  • With a round section. This is the most durable material for mowing herbaceous plants;
  • With curly section. Used to mow soft plants;
  • Twisted. Used for thin grass;
  • Professional type, is not suitable for all models of technology.
See also  electric grass trimmer is the best for the grass

To change the fishing line for a trimmer on a lawn mower, it is necessary to purchase a cutting thread that will be ideal for a particular type of mower.

You can soak the thread in a basin of water for several minutes to increase elasticity and strength.

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. Specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
  • Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
  • Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

All about the replacement of fishing line with a trimmer head

There are many types of heads that are designed for different types of fishing line. The latter is also available in several diameters: from 1.0 mm to 3.2 mm. At the same time, its section is round (including with a special groove to reduce noise), square, twisted and in the shape of a star.

There are no clear preferences, and this explains the wide variety of forms and diameters in the market. The round shape is usually stronger, but has a worst cutting ability, in addition, when rotation, it makes a characteristic sound. Therefore, sometimes they make an acoustic groove, however, the use of this fishing line makes sense only on battery trimmers, in machines with gasoline and network drive, the sound level of the drive itself practically drowses the sound from the fishing line. The square has a good cutting ability, and despite the fact that such a fishing line for a trimmer is less durable than round, on average it is consumed less. A square fishing line for a trimmer quite easily cuts the shoots of the same Ivnyak up to 1 cm in diameter. The star has the maximum number of cutting faces, mows best and is the fastest consumed.

The next nuance when choosing is stiffness. The fact is that in the production of nylon, a modifier (often maleine anhydride) is added to it, which improves its strength and prevents gaps. However, modifiers are not the cheapest component, they are trying to save on it. Therefore, it seems to be a good fishing line for a trimmer that remained for the winter, in the spring unexpectedly behaves completely differently. It breaks, stops going out normally from the reel. There is a recommendation to soak a fishing line for a trimmer in water before work, but I do not see much sense in this, malein anhydride interacts with water, but if it is not enough in the nylon, then there will be nothing to interact. Therefore, it makes no sense to stock up on fishing line for a long period of time, a breakdown or constantly torn fishing line for a trimmer, which also does not want to leave the reel itself, can significantly complicate the work.

Lespecker replacement instructions

Before starting to replace the string, it is important to clarify what type the coil is installed in your trimmer. They are to work with one, two antennae. Fishing line for a trimmer for functioning with one osmus is quite simple:

  • In the inside of the coil there is a special ear where you need to insert one end of the string. It is necessary to extend the cord in the opposite direction from rotation of the coil. About 2-4 m fishing line will be enough for this. Upon completion of the winding, the second free end of the small length must be fixed in a specially provided groove, so that in the process of working a trimmer for the grass the fishing line for a trimmer does not unwind.
See also  Which gasoline braid for grass is better. Lawn mowers by engine type

If the coil works with two ends of the cord, then a number of the following procedures are performed to refuel the fishing line:

  • Determine how many holes for fishing line are in the reel. If the seizure is one, then both ends will be extended through it. If two each of them is entered into the hotel hole.
  • Measure 2-4 meters of a nylon string, cut a measured piece and deliver both ends to the allotted recesses.
  • Wrap both threads in the opposite direction from the one in which the coil rotates.
  • At the end of the free ends of the cord, fix in the grooves. If there are no one, hold your hand.
  • Find a hole (ear) on the outer side of the coil and pass both ends there.
  • Collect the drum and insert it into the gas mowing housing.

wind, fishing, line, trimmer, lawn, mower

Winding process

If your coil is designed to work with only one osmus, then everything is simple here. It is necessary to rewind 2-4 m of fishing line (depending on the size of the coil), find the hole for the trimmer on the inside of the coil, insert one end of the fishing line there and start to wind the fishing line for the trimmer in the direction in the reverse direction of rotation of the coil at the trimmer. The inside of the coil is usually indicated with an arrow in which the side is to wind a fishing line for a trimmer. Having wiped a fishing line for a trimmer, we leave its small piece unnecessary to put it out. We fix this piece in a special groove located on the inner part of the coil and designed so that at the time of collecting the coil of the fishing line for a trimmer does not unwind. If there is no such groove, then you will have to hold a fishing line for a trimmer with a finger, so as not to let it unwind during the further collection of the coil. Next, we take the outer part of the coil and spread the outer piece of fishing line into the available hole, collect and put the coil back to the trimmer for the grass.

If the coil is designed to work with two antennae, then we do the following. On the inside of the coil, we look at how many grooves are available for winding fishing. There may be one or two of them. If the groove is one, then both antennae are wound on this one groove. If there are two grooves, then each antennae is wound in a groove. The coil with one groove should have a through hole in which a fishing line for a trimmer is threaded. We open 2-4 m of fishing line, we extend it through this hole so that on each side of the fishing line it sticks the same. And we will simultaneously wrap both the antennae of the fishing line in one direction, the reverse direction of rotation of the coil in the trimmer and coinciding with the direction indicated by the arrow available on the inner part of the coil. We leave a little fishing fishing line, we fix the resulting ends in special grooves, and if they are not, we hold with your fingers. We spread both ends into the available holes on the outer body of the coil. Collect the coil and fasten it to the trimmer.

In the presence of two grooves, a piece of fishing line 2-4 m long is folded in half, we insert the loop in the groove between two grooves at the bending site, and we wind both the ends of the fishing line each in its groove at the same time. Further actions are similar to the previous option.

There are also coils, in which a fishing line for a trimmer is threaded through a through hole on the inside. After that, the ends of the fishing line, without wrapping, spread completely through the holes on the outer body of the coil, collect the coil and begin to rotate the button that is usually pressed in order to release the fishing line for the trimmer while it is worn out. Rotate the button. Inside the trimmer fishing line is wound itself. At the same time, it will not work to twist it in the “wrong” direction, since it can spin only in one direction. If you get used to it, then you can wrap a fishing line for a trimmer to such a reel without even taking it out. You just need to combine the through hole of the internal drum with holes on the outer body of the coil, and then pass the fishing line for the trimmer in them.

| Denial of responsibility | Contacts |RSS