Trimmeres repair (benzos, electrocos) OLEO-MAC (OLEO-MAC)

When buying a chainsaw, the carburetor has factory settings and adjusted to optimal operating modes. However, during operation, the engine (ICE), the fuel pump, the carburetor wear out, as a result of which they are required to carry out their repair, maintenance and settings. In this case, the role of the carburetor is the restriction of the minimum and maximum revolutions of the ICE.

The main criteria to determine the need to adjust the carburetor:

  • The engine does not start, stalls, does not respond to the pressing of the accelerator;
  • lack of idle;
  • increased fuel consumption, ICE does not develop power;
  • wear of the piston group, sooty codes on the spark plugs, black exhaust gases, incomplete combustion of gasoline.

The reasons for the carburetor settings failure are as follows:

  • violation of the fixation of the screws that regulate the minimum and maximum engine speed, due to strong vibrations or mechanical influences;
  • with wear of the piston system of internal combustion engine;
  • blockage of air or fuel filters, jackets, fuel channel, intake valve breakdown.
electric, oleo-mac, chainsaw

To configure the carburetor, it is important to understand what parts and nodes it consists of the principle of its operation. This will determine the reasons for the failure, which preparation tools for adjustment and the type of reprimatum, if you need to repair.

Design and principle of operation

The principle of operation of the carburetor is based on mixing the fuel mixture of fuel and air with air in a certain proportion for effective ignition and their complete combustion in the internal combustion engine. It is a whole.liter case, inside which the following structural elements are located:

  • fuel chamber;
  • air and fuel channels;
  • Junkers: idle and main;
  • Fuel filter set
  • inlet and exhaust fuel valves;
  • air and throttle;
  • diffuser;
  • fuel and control membranes;
  • adjusting screws;
  • Sealing gaskets.

The screws are displayed outside the housing to adjust the quality and composition of the mixture. In the upper and end part there is a pipe for supplying fuel and the pulse channel of the fuel pump.

The carburetor works according to the following algorithm:

  • At the time of starting the engine, the air damper is opened. The air passes through the filter and bypassing the shutters (on the scheme number 1), it enters the case.
  • Fuel pump pumps gasoline into the chamber. Under pressure through the jackets (on the scheme above position 2-the main jet, 3.4-nozzle jetlaws) is sprayed with an oil-banzin mixture, contacts with air, mixed, and then enters the combustion chamber. The engine starts to work at idle.
  • When you press the accelerator, the second adjustable throttle is opened to a certain angle (in the photo this is the second damper), the fuel begins to be supplied through the main jacket (position 2 in the diagram). Inside the carburetor, a larger number of combustible mixture is mixed, which, when supplied to the combustion chamber, increases the frequency of engine rotation.
  • The amount of gasoline entering the chamber also depends on the settings of the adjusting screws that control needle valves (in the diagram these are spring.loaded screws on the left and right).
  • Fuel supply to the chamber is limited to membranes, the supply intensity is determined by a change in the pressure in the piston and is regulated through the feedback of the pump and the pulse valve. The operation of the fuel pump is synchronized with the engine: the higher the revolution, the stronger the flow of the fuel-air mixture.
  • To exclude overflow of fuel in the chamber, a special lever and an overlapping valve are provided.

Carburetor fuel supply system. 1. control camera; 2. membrane; 3. locking needle.

Tools for configuration

Since adjustment is performed using external screws, a cross or flat screwdriver that is coming included in the set will be needed, the width of the working part is 4 mm. To control the speed of revolutions, a tachometer will be required.

Step.by.step adjustment

An example of adjusting the carburetor will be analyzed by the example of the OLEO-MAC 937 chainsaw. The principle of setting up other saws is practically no different, so this algorithm is applicable to the following models: 941C, 936. With other, less popular models (for example, OLEO-MAC 362 or OLEO-MAC 35), the similarity was not checked, but most likely there are no serious differences.

electric, oleo-mac, chainsaw

Before setting up the Oleo-Mac chainsaw carburetor, a number of conditions should be met:

  • clean air and fuel filters;
  • check the state of the jackets, make sure of their serviceability and cleanliness;
  • evaluate the integrity of membranes: lack of damage, cracks;
  • Check the intake of the fuel chamber in sufficient quantities.

For standard adjustment of the carburetor, it is not required to disassemble it. Outside are screws that allow you to perform all the necessary settings:

Despite the fact that the manufacturer recommends adjusting only the “S” screw, in practice this is not enough. Before adjustment, all three screws should be twisted to the stop, and then unscrew at 1.5-2 revolutions.

OLEO-MAC equipment maintenance procedure.

Oleo-Mac chainsaws are installed gasoline membrane carburetors manufactured by WALBRO for two-stroke engines. They are distinguished by simplicity of design, maintainability, unpretentiousness in operation. WALBRO is part of the STIHL group of companies, so it produces products that meet world quality standards.

OLEO-MAC 1800E Instruction Instruction Online. Page 57

Instruction Oleo-Mac 1800e for the device Electric saw contains pages in Russian.

You can download PDF file of this instruction: download pdf

ATTENTION! Always stop the car and disconnect the supply

the cable before proceeding to the implementation of all operations indicated

in the table below, with the exception of cases when required

If the malfunction remains after all the checks, contact the authorized service center. In the event of a malfunction not indicated in this table, contact the authorized service center.

The engine is not launched or ruso. (Uda. Cho.ah and b.s is connected to the network)

damaged

the center of technical support: contact the authorized

the center of technical support: contact the authorized

The engine does not gain full speed and/or smokes strongly.

and the frequency in the power grid of the chain is too

strongly

“Installation of the tire and chain” (. 85).Rev

Extensive wires (230V); cm. table in the Start section (.91)

And z.s and in the s and l and damaged brushes

The tire and chain heat up and smoke during operation

“Installation of the tire and chain” (. 85).Let the engine work on

NEVAR DO KOUSHETS

D and g.a t e l z a p s to s, but the chain does not rotate

“Usage. Chain brake “(p. 95) tension of the chain; cm. Instructions in the section

“Installation of the tire and chain” (. 85) see. instructions in the section “Installation of the tire and

chains “(p. 85) see. Instructions in the section “Technical service

Tires and/or chains “(P. 101) Replace: contact the authorized

In n and m and e: do not touch the circuit while the engine works

UWAGA: przed przystąpieniem do jakichkolwiek czynności zalecanych w poniższej tabeli należy zawsze wyłączyć urządzenie i odłączyć je od zasilania, za wyjątkiem napraw wymagających działania urządzenia.

PO SPRAWDZENIU WSZYSTKICH MOżLIWYCH PRYZYCZYN, JEYLI PROBLEM NIE ZOSTALL ROZWIązany, NALEAżY ZWRócić Się do autoryzowanego serwisu. Je Pojawi się usterka nie wymieniona w tabeli, należy zwrócić się do autoryzowanego serwisu.

Silnik nie uruchamia się lub pracuje w niegularny sposób. (Upewnić się, że kabel zasilania jest podłączony do sieci)

W y m i e n i ech: s k o n t a k t o w a ć s i ę z

autoryzowanym serwisemw y m i e n i ć: s k o n t a k t o w a ć s i ę z

autoryzowanym serwisemw y m i e n i ć: s k o n t a k t o w a ć s i ę z

N i e p r a w i d ł o w e n a p i ę es

Lub częstotliwo bow zasilania siecioegoz by t n a p ręo ny ń s c h

SPRAWDZIFI PARAMETRY ZACILANIA SECIOWEGO

PrzedStaWione W Rozdziale “Montaż Prowadncy i łańcucha” (Str. 85).Zalecane długości przedłużaczy (230 v);

Patrz Tabela W Rozdziale “Rozruch” (Str. 91)

WYMIENIICH: SKONTAKTOWAWARIę Z Autoryzowanym Serwisem

P r o w a d n i c s a z ł a ń c u c h nagrzewają się i dymią podczas pracy urządzenia

SMAROWANIA łCUCHAZBYT Naprężony łańcuch

Prowadncy i łańcucha ”(str. 85).URUCHOMICH NA PELENYCH OBROTACH NA

Czy Z końcówki Prowadnicy Kapią Krople

Oleju. Jeżeli dochodzi do wycieku oleju,

b r a k u o l e j u s k o n t a k t o w a ć s i ę z

Silnik uruchamia się i działa, ale łańcuch się nie obraca

Prowadnicy I łańcuchauszkodzony/a łańcuch I/lub

Wyłączyich hamulec łańcuchaa; Patrz Rozdzia

“Użytkowanie. Hamulec łańcucha (str. 95) napinanie łańcuccha; Patrz Instrukcje

Prowadncy i łańcucha ”(str. 85) Patrz Instrukcje PrzedStawione W Rozdziale

“Montaż promunacy i łańcucha” (str. 85) Patrz Instrukcje PrzedStawione W Rozdziale

Oleo-Mac chainsaw is not started

The chainsaws are a little different between structural features, but almost always the assembly principle is carried out according to two standard schemes. Many devices have information about the need to activate the brake of a critical installation before you start the inclusion function.

You should first master the installation of the plant and study the main methods of correction of breakdowns, then a person will have the opportunity to fully operate the device.

Briefly about the installation of the plant

Basopile works from a gasoline engine. This is a common device, the design of which has no special bells. The main reasons why the chainsaws of the Italian chainsaw Oleo-Mac 936 are not started. It usually works properly even in languid criteria for this.

Following the factory device, the functioning is provided by structural elements:

  • Carburetor engine (see. Carburetor adjustment).
  • Clipers of centrifugal type clutch.
  • Ignition system, in fact, in all devices are contactless.
  • Carburetor that adds air to the fuel mixture.
  • Fuel system. Today about the stihl chainsaw that the Stihl 180 chainsaw is not started and floods the candle. Its standard device consists of a hose, filter and gas tank, but from time to time it has additional details.
  • Starter.
  • Tire.
  • Chain (see. Oil for the chain).
  • Tension mechanism and circuit brake (see. how to sharpen a chain).

Step-by-step instruction

With an activated brake, the assembly process occurs much slower, so everything is also safe and more comfortable to turn on the mechanism without the use of brake equipment.

If a person is not sure of his knowledge and accuracy, then the brake, on the contrary, needs to activate. With the right order of action, the device does not start, the mechanism will not make actions dangerous for a person.

Duration and procedure for repairing chainsaws and electric saw Oleo-Mac

Most often, the repair of chainsaws and electric saw OLEO-MAC in our service center does not exceed 5 days. Often we can even eliminate the problem during the day. During the repair, the difficulty of the breakdown and the presence of the necessary spare parts affect. If in the warehouse of our company or our suppliers there is no necessary spare part, then it will need to be ordered from the direct manufacturer. In such cases, the period of repairs may be delayed for about a month. Our managers pre.inform customers about this.

We optimized the repair process as much as possible, and it includes 5 stages:

  • You bring your broken chainsaw or OLEO-MAC electric saw to our service center.
  • We quickly diagnose it.
  • Then we contact you, we talk about the revealed malfunctions, cost, as well as the terms of repair.
  • You agree or refuse to repair.
  • Then take your Oleo-Mac technique!

Oleo-Mac power supply warranty for the repair of chainsaws

Our service center is completely confident in the high quality of the services provided and the spare parts used in the repair process. Therefore, we are confidently giving a three-month guarantee for all replaced parts and performed repair of the chainsaw and electric saw OLEO-MAC. If you again have a malfunction that was eliminated earlier by our experts, then it will be corrected by us absolutely free and in the shortest possible time.

And the search circle is narrowed to the models applicable to your criterion.

Adjustment of the OLEO-MAC chain carburetor

To configure the standard carburetor of the OLEO-MAC proprietary chainsaw, its factory device provides for 3 metal screws:

  • screw L. is responsible for adjusting the operation of the motor at starting low speeds;
  • screw h. is needed to adjust the maximum revolutions of the built.in engine;
  • screw t. allows you to set the number of ICE speeds when idling.

The tuning of the OLEO-MAC chain carburetor is performed in the following sequence:

  • First, on a tool with a drowned ICE, you need to install factory settings of the built.in carburetor. To do this, they need to be turned as indicated in the instructions;
  • Next, you need to start the engine, wait for it to warm up and configure the operation of the internal combustion engine at low speeds. To do this, the standard screw L needs to slowly turn clockwise until the engine becomes stably and evenly;
  • If after that the chain on the tire rotates continuously, then the T.Ts Tame will need to be rotated in different directions until the headset stops;
  • Further, you need to connect a manual tachometer to the saw and turn the screw h so that the indicators of the device and instructions in the instructions are completely matching.

The chainsaw is not started ! Fast and effective repair without costs!

To check the operation of the engine, you need to start a chainsaw and press the gas trigger several times. If at the same time, the ICE sharply gains momentum without making extraneous sounds, then the control of the node was successfully performed.

A chainsaw is a technically complex tool that must be served from time to time. Cleaning, replacing filters and of course adjusting the gasopyle carburetor, will help to last the entire time she has set for it. In this article we will consider the issue of setting a carburetor. How and for what it is carried out.

Repair of Oleo-Mac chainsaw carburetors

If the OLEO-MAC chainsaw carburetor sets up, it probably needs to be repaired. This can be determined by the following symptoms:

  • The engine spontaneously and sharply changes turns, stalls, does not start;
  • increased gasoline consumption;
  • the presence of vibrations or increased noise during operation;
  • exhaust gases of dark color.

To access the carburetor, you need to remove the lid on the chainsaw housing, and then the air filter. Actions are required to be performed carefully and without the use of unnecessary efforts.

Malfunctions and methods for their elimination

There may be common malfunctions:

  • clogging of filters or jackets, eliminated by cleaning;
  • damage to the membrane (performs the role of the pump), is solved by replacement;
  • The failure of the sealing gaskets, it is necessary to replace with new parts of the carburetor after parsing the corps parts;
  • The jamming of the valve (the needle that covers the supply of fuel in the carburetor) requires an assessment of its condition to determine the possibility of its further operation or replacement;
  • Violation of the contact of the lever of the air damper with an accelerator, restoration, repair or replacement of the assembly is required.

Often some of the listed problems arise after prolonged downtime of the chainsaw. To restore performance, it is required to complete the full maintenance of components and pre.trial detention centers.

Is it worth it to carry out independent repairs

Independent repair of the OLEO-MAC chainsaw carburetor is appropriate in the following cases:

  • The breakdown is simple, obvious, there are the necessary details;
  • there is experience in performing such works, qualifications;
  • The warranty from the manufacturer is not lost;
  • there is no way to contact the service center or is it financially unprofitable.

It is worth clearly understanding that independent repair cannot guarantee a positive outcome of events. Therefore, it is worth taking it only if there are knowledge about the design and principle of the carburetor.

Remkomplekt for the carburetor

For the repair of the carburetor, you will need a remote control, the composition of which is as follows:

The average can be purchased in specialized stores or service centers. There is also the possibility of buying chainsaw manufacturers in online stores, dealers.

OLEO-MAC 937 chainsaw-model description

This Oleo-Mac model is a list of the latest developments from the Italian brand. The tool is intended for regular work to remove branches, cutting trees with small and medium diameter trunks, as well as clearing shrubs.

OLEO-MAC 937 chainsaw is equipped with a 2-stroke gasoline engine, 1.6 kW and cylinder volume 35.2 cm3. The working cylinder of the model is made of nickel alloy, and the connecting rod and crankshaft are made of hardened steel. The use of corrosion resistant and damage to materials increases the life of parts in difficult weather conditions

The manufacturer has provided free access to the air filter and the muffler of the tool. This greatly simplifies the maintenance and repair of parts in the field.

A high.quality branded headset is responsible for cutting wood. For its production, a metal alloy is used, which is distinguished by resistance to shock and other mechanical damage. To tension the Oleo-Mac saw chain, it is equipped with a lateral tensioner, which does not require the use of manual tools for adjusting.

  • The power of the standard ICE is 2.2 liters. With.;
  • tank for pouring the fuel mixture. 320 ml;
  • the possible length of the tire used for operation is 30–35 cm;
  • The step of the standard chain is 3/8 “;
  • The mass in the form assembled for work is 4.3 kg.

The low weight of this Oleo-Mac tool gives its owner the opportunity to work at high altitude. An effective anti.vibration system extinguishes the fluctuations of the crankshaft of the engine, simplifying the work with the tool.

Launch and work

All controls are compactly placed in the area of ​​the rear handle and are available for one hand. The gas trigger is mounted on the handle itself, it controls the opening of the throttle, adjusting the amount of the finished mixture entering the cylinder. The lock protects the user from randomly launching a saw. On the right is a primer for pumping fuel to a carburetor and a universal switch combining air damper and ignition.

Read how to make a line for a circular saw

For the first launch, it is lowered to the lower position, during operation it is on average, and by moving the lever up, turn off the current that goes to the candle and the saw is jerking off.

Tire and chain

In the box with the device is a tire of 16 inches long, which corresponds to 40 cm. This size is enough for most homework. Although if desired, you can put a tire of 45 and even 50 cm long. the power allows. But it is worth remembering that this step is justified only if you are dealing with loose soft wood, otherwise you can easily overheat the engine. The operation itself does not represent anything complicated. the tire is attached to the studs and fixed with nuts. The chain tensioner is on the side.

In order to have the canvas longer, an automatic lubricant system is provided. The pump takes the oil from the tank in the front of the saw and sends it to the chain through special channels. To regulate the quantity there is a special screw from the bottom of the case.

The chain brake is responsible for safety, which, when rebuilding or intentional pressing, turns off the clutch and blocks the leading star.

Fuel and air supply systems

The carburetor is intended for the preparation of the fuel-air mixture. Most often, Oleo-Mac puts on its saws reliable Walbro nodes, which are simple, reliability and a wide range of settings. The air is absorbed through a special filter made of fine polymer mesh in the form of a small box. For access to the filter, carburetor and candle, the upper fast.fast lid is provided. To dismantle it, it is enough to unscrew one barack nut. This can be done both with the help of a screwdriver, and without it, with the help of influxes on a plastic cap.

Oleo-Mac 937 chainsaw repair with your own hands

Details: Repair of the Oleo-Mac 937 chainsaw with your own hands from a real master for Olenord.com.

Repair of such a chainsaw costs significant cash. What exactly has broken down.

РЕМОНТ БЕНЗОПИЛЫ. РЕМОНТ БЕНЗОПИЛЫ OLEO MAC. OLEO MAC 947

I want to buy a gas tank mtl51. Who previously dealt with him, tell me this is good.

OLEO-MAC 952 chainships need to replace the chain. I really don’t want to buy.

who will answer me why the oil does not enter the chain

one.Perhaps the hole on the tire does not coincide with the hole at the tire attachment (the tire is not native) to remove the tire and circuit, start the saw, see if the oil is supplied without a tire; 2. Perhaps the gear of the oil pump drive (not high.quality oil is made, too viscous oil, oil with water, etc.D. and t.P.) There is only one way out. to the service.

Start a saw with difficulty, but begins to work at full power, when I start to gam it, it stalls, there is a spark, does not throw a candle. What can you tell?

Hello! No oil supply to the Oleo-Mac saw chain. How to get to an oil pump?

Why is the gas tank vacuum, there is no saopon on the lid?

Binzopila Oleo Mas 937 with a full gas supply stalls

b.P. Oleo Mas is not started at idle. I turn on the operating mode, with my foot under the accelerator, I work, it works. I drop the turnover- stalls

On the chain email Oleo-Mac 1700 I need to remove the spring washer installed on the output shaft, whether it is possible to remove it without mutilating it?

Good day to fart yak to depreciate the carburetor? Rolobil cleaned now not starting up ! Craco yak screw?

Start a saw with difficulty, but begins to work at full power, when I start to gam it, it stalls, there is a spark, does not throw a candle. What can you tell?

Oleo. Mac 937 start, does not work much and stalls, what’s the reason?

Oleo. Mac 937 start, does not work much and stalls, what’s the reason?

You can repair the Oleo-Mac 937 chainsaw, and only if you change the studs, then it’s just. Take and disassemble the cover itself, then get to the basket and replace everything you need.

how to replace a carburetor slag by 937 (

5) how many water steam can be contained in 2 m3 of air at a temperature of 10 degrees C? how many water steam need to be added to saturate this air with an increase in temperature to 20 degrees from?

There was no hot water. Heating heating is disconnected when opening the crane in the input boiler turns on but heating is heated and water.The water circulation is normal, the heating circuit is blocked by cranes, but the heating continues the heating of the AA error.

I ask about the norm of cold water. since we don’t have hot. And there is no bathroom. Not a soul

Who will answer me why the oil does not enter the chain

Who will answer me why the oil does not enter the chain

Everything is possible, but is it practical? I wouldn’t do so for myself.

If all sizes are known, then you need to change everything, here in more detail http: // www.Webmath.ru/poleznoe/formules7.PHP

Good afternoon, I decided to start the repair, in the apartment, with my own hands, but when I reached my daughter’s room, I wanted to increase the size of the room due to the balcony, I can.

Hello! In the near future I am going to purchase the Rotenberger tool. Tell me where it is more profitable to buy in or in Ukraine, I just plan to go.

At what distance from each other can a well with clean water and the drain of sewage?

I think to buy a stencil and do as builders do. But there are a couple of questions. Firstly, what plaster to buy for the 2nd layer, which is applied immediately after the stencil?

The neighbors in the summer cottage are advised to build a house from a gallery beam brought from Arkhangelsk. It is interesting to know from specialists what such wood is appreciated.

Tender and romantic design of a small.sized hallway. Light wallpaper with the image of clusters of grapes is an excellent background of an unusual vase with flowers and an old wooden hanger

Brands such as Husqvarna, Partner, Solo, Oleo.

the city you need to purchase oleo-mac spare parts? If you write.

The chainsaw was covered after the first refueling. Please tell me, maybe I’m something.

I have been working this chain-as Oleo-Mac Sparta 25 for 4 years and is very pleased, not yet not yet.

here she is http: // www.Motopila.ru/doc/benzo/oleo-mac/962/

олеомак 947, OLEO-MAC 947

bought this model of a chainsaw, in my opinion the average.

there is a lot of the chain I don’t know that it happened yesterday everything worked

Looking for reviews on Oleo-Mac Sparta 25 Tr Eco. I will be grateful for the help.

Chain saw “Oleo-Mack 937”: Description and characteristics

Before choosing a chainsaw, you need to decide which class of tools is suitable for you better. As for household models, they are designed for a very limited time within a month. Semi.professional saws, also called agricultural tools, are able to cope with more complex tasks. With their help it will be possible to cut down trees and carry out construction work. Perhaps this type of equipment is suitable for you if you plan to build a holiday home or bathhouse.

But professional saws can work at least 10 hours a day. The main feature of this tool is the ability to use an engine without interruptions. On sale today you can find special saws designed for manipulation inside the crown of trees. This is especially true when you need to take care of greens. Such models usually have an optimal center of gravity and lightweight. Among other saws on the market. Model “Oleo-Mack 937”. This will be discussed below.

Oleo-Mac 937 chainsaw repair with your own hands

Details: Repair of the Oleo-Mac 937 chainsaw with your own hands from a real master for Olenord.com.

electric, oleo-mac, chainsaw

Repair of such a chainsaw costs significant cash. What exactly has broken down.

I want to buy a gas tank mtl51. Who previously dealt with him, tell me this is good.

OLEO-MAC 952 chainships need to replace the chain. I really don’t want to buy.

who will answer me why the oil does not enter the chain

one.Perhaps the hole on the tire does not coincide with the hole at the tire attachment (the tire is not native) to remove the tire and circuit, start the saw, see if the oil is supplied without a tire; 2. Perhaps the gear of the oil pump drive (not high.quality oil is made, too viscous oil, oil with water, etc.D. and t.P.) There is only one way out. to the service.

Start a saw with difficulty, but begins to work at full power, when I start to gam it, it stalls, there is a spark, does not throw a candle. What can you tell?

Hello! No oil supply to the Oleo-Mac saw chain. How to get to an oil pump?

Why is the gas tank vacuum, there is no saopon on the lid?

Binzopila Oleo Mas 937 with a full gas supply stalls

b.P. Oleo Mas is not started at idle. I turn on the operating mode, with my foot under the accelerator, I work, it works. I drop the turnover- stalls

On the chain email Oleo-Mac 1700 I need to remove the spring washer installed on the output shaft, whether it is possible to remove it without mutilating it?

Good day to fart yak to depreciate the carburetor? Rolobil cleaned now not starting up ! Craco yak screw?

Start a saw with difficulty, but begins to work at full power, when I start to gam it, it stalls, there is a spark, does not throw a candle. What can you tell?

Oleo. Mac 937 start, does not work much and stalls, what’s the reason?

Oleo. Mac 937 start, does not work much and stalls, what’s the reason?

You can repair the Oleo-Mac 937 chainsaw, and only if you change the studs, then it’s just. Take and disassemble the cover itself, then get to the basket and replace everything you need.

how to replace a carburetor slag by 937 (

5) how many water steam can be contained in 2 m3 of air at a temperature of 10 degrees C? how many water steam need to be added to saturate this air with an increase in temperature to 20 degrees from?

There was no hot water. Heating heating is disconnected when opening the crane in the input boiler turns on but heating is heated and water.The water circulation is normal, the heating circuit is blocked by cranes, but the heating continues the heating of the AA error.

I ask about the norm of cold water. since we don’t have hot. And there is no bathroom. Not a soul

Who will answer me why the oil does not enter the chain

Who will answer me why the oil does not enter the chain

Everything is possible, but is it practical? I wouldn’t do so for myself.

If all sizes are known, then you need to change everything, here in more detail http: // www.Webmath.ru/poleznoe/formules7.PHP

Good afternoon, I decided to start the repair, in the apartment, with my own hands, but when I reached my daughter’s room, I wanted to increase the size of the room due to the balcony, I can.

Hello! In the near future I am going to purchase the Rotenberger tool. Tell me where it is more profitable to buy in or in Ukraine, I just plan to go.

At what distance from each other can a well with clean water and the drain of sewage?

I think to buy a stencil and do as builders do. But there are a couple of questions. Firstly, what plaster to buy for the 2nd layer, which is applied immediately after the stencil?

The neighbors in the summer cottage are advised to build a house from a gallery beam brought from Arkhangelsk. It is interesting to know from specialists what such wood is appreciated.

Tender and romantic design of a small.sized hallway. Light wallpaper with the image of clusters of grapes is an excellent background of an unusual vase with flowers and an old wooden hanger

Brands such as Husqvarna, Partner, Solo, Oleo.

electric, oleo-mac, chainsaw

the city you need to purchase oleo-mac spare parts? If you write.

The chainsaw was covered after the first refueling. Please tell me, maybe I’m something.

I have been working this chain-as Oleo-Mac Sparta 25 for 4 years and is very pleased, not yet not yet.

here she is http: // www.Motopila.ru/doc/benzo/oleo-mac/962/

bought this model of a chainsaw, in my opinion the average.

there is a lot of the chain I don’t know that it happened yesterday everything worked

Looking for reviews on Oleo-Mac Sparta 25 Tr Eco. I will be grateful for the help.

Chain saw “Oleo-Mack 937”: Description and characteristics

Before choosing a chainsaw, you need to decide which class of tools is suitable for you better. As for household models, they are designed for a very limited time within a month. Semi.professional saws, also called agricultural tools, are able to cope with more complex tasks. With their help it will be possible to cut down trees and carry out construction work. Perhaps this type of equipment is suitable for you if you plan to build a holiday home or bathhouse.

But professional saws can work at least 10 hours a day. The main feature of this tool is the ability to use an engine without interruptions. On sale today you can find special saws designed for manipulation inside the crown of trees. This is especially true when you need to take care of greens. Such models usually have an optimal center of gravity and lightweight. Among other saws on the market. Model “Oleo-Mack 937”. This will be discussed below.

| Denial of responsibility | Contacts |RSS