Adjustment of the Stihl lawn mower

The Stihl FS 55 lawn mower, the operating annotation of which is delivered in the kit and must be investigated before work, is a high.tech equipment that is not difficult to maintain. You can without the help of others to repair and adjust. As for the carburetor, this is 5 minutes.

The main defects of the malfunction of the carburetor can be breakdowns and blockage. In order to find out the cause, unscrew the fuel filter lid and pull out the mesh filter. If mud accumulated on it, then purging or washing in gasoline will help. If you have found visible configurations on the filter, then it should be changed to a new.

Perhaps the pitch rods of fuel will also be damaged. Refusal to operate the starting device of the carburetor can occur due to gaps. For washing, gasoline or acetone is used. The carburetor can be passed by compressed air, for this you can use a comfortable repair practice. Depressurized may be a graduation or intake pipeline, also the hull of throttle shifts and those places where the parts of the carburetor are connected among themselves. If you are faced with the aforementioned inconsistent, then you can make sure of it with a soap solution, which is applied to the suitable area.

Technical characteristics and special

Thanks to the fuel pump of a manual plan, a person will easily be able to pump up fuel into a carburetor. This moment is especially important in the situation when the gas station stood for a long time idle. Constantly pouring fuel will allow you to quickly start the device even after “long leave”.

replacing, carburetor, stihl, station, seals, fs38

Together with the unit, the owner receives in the configuration of patronage glasses and a mowing head. It is possible to deal with the assembly features and other specific moments of operation thanks to the guidance presented on our website.

Other useful information should be familiarized with the following document:

The curved rod of the Stihl FS 38 lawn mower with a rounded handle is worthy of considerable attention. Thanks to this design, the device easily copes with cleaning the territory even in a narrow or limited space.

All controls are placed on a convenient handle, so look for a long time where and what switches does not need. During operation, such a moment is very important, because the operator may not be distracted and without unnecessary movements regulate the operation of the machine.

Stihl FS 55 Lawn Mushroom

The introduction of a lawn mower in landscaping works implies the presence of wear, and sometimes breakdowns of its devices. But since this tool cannot be attributed to complex household devices, all breakdowns are only of mechanical disposition that can be corrected with your own hands. In some cases, there are enough adjustment work that return the tool to normal working condition. One of these operations is the adjustment of the gas mowing carburetor in manual mode. The task of the carburetor is to mix air with fuel before supplying to the engine. And if the proportions do not coincide, there will be visible malfunctions in the work of a trimmer for the grass:

The whole process of adjusting the carburetor of the brand Motokos provides only to debugging the position of three screws: l. adjusting the supply of gasoline in the spit at low speeds, h. adjusting high revolutions and fuel consumption, t. idle debugging. So, if you need to configure the carburetor of a gasoline braid for the grass of the line of brand 55 or other types of this series, the following actions are performed:

  • The engine warms up (10 minutes of idle is enough).
  • The screw n is adjusted, turning to the left/right until the maximum idle speed.
  • From the found point, unscrew counterclockwise in ¼ turn, which will set the right working position.
  • Setting up the idle passage of the carburetor of the benzo.cockered occurs similarly, turning against the clock (reducing speed) and clockwork (increasing speed). The position of maximum stability of the motor at different positions is achieved.
  • The screw l is also regulated by small enjoying to the maximum indicator.

The whole process is carried out by ear, therefore, for more successful work, it is worth acquiring a tanometer. The tools can be performed as accurately as possible from the masters of the “braid for Motors grass”, as well as buy oil for the compressor and purchase all the necessary spare parts and components for timely maintenance.

STIHL FS 55. Carburetor adjustment (idle)

Adjustment of the carburetor trimmer for the STIHL FS 55 grass in the video is performed in order to adjust the storage of idle.

Repair of the Stihl FS55 lawn mower carburetor

Replacing the sealing ring, accelerator in the carburetor of the lawn mower (benzotrimer) STIHL FS55.

What is the adjustment of the carburetor 55 for

Working with a series of gasolimers portends active use, since the performance of this unit is not limited to aligning the lawns. As a result, miscalculations appear in the engine, and the carburetor is adjustable 55 with the implementation of simple manipulations. The malfunctions are unpleasant and promised with inferior work or embezzlement for fuel, eaten in large quantities. You should think about setting up the carburetor trimmer for grass in cases where:

  • Inexplicable motor stops after starting it are observed;
  • In the process of operation, the engine of 250 series of braids for grass through an unconnected mechanism for feeding the mixture “sobs” at loads.
  • Work is accompanied by an increased amount of gas exhaust.

In any case, each of the reasons consists in mixing air and gasoline, where the carburetor adjustment of the model 130 will avoid unexpected stops of the motor in the middle of work. The system of professional gasoline braid for grass 130 with a rigid drive shaft provides rapid cutting of wood, which with a lack of air in fuel will turn the motor. On the other hand, the settled mixer of the 38 line or trimmer for the grass of the model line 450 will not to spit out gasoline at applied loads, when there is often a lack of air in the carburetor. In the company “Spit for Motors grass” you can purchase all components for motors, find out information about setting, as well as buy a candle key and other spare parts for successful repairs.

So, guided by all the requirements and technical recommendations, the carburetor motorcosa is adjusted to improve its performance. The process of checking the results obtained begins even from the first steps, when the lawn mowers are idle at the idle move with screws to regulate the fuel supply mixer. For example, if after controlling the screw of reduced capacities, failures in operation stop, a screw of maximum revolutions can not be disturbed. For persuasion, it is enough to turn the latter forward, where the presence of failures instead of increasing power will show that the mechanism was adjusted, and it is worth returning the screw to its original position.

Also, a properly configured mowing of the 55 series will show that the applied load does not affect performance. The process of diagnosing a do.it.yourself control of the carburetor mechanism will be accompanied by:

  • Lack of failures when rotating screws.
  • Lack of failures in idle, even when changes in the position of the tool;
  • Lack of symptoms with full workload.

Here you should test the gasolimmer carefully, increasing the load from small portions to the maximum allowable processing object. Also, in order to prevent other problems, the “braid for grass-motors” recommends timely conducting a mowing inspection in a timely manner, for which it is worth arming with knowledge, as well as order a lubricant for the gearbox and other components and mechanisms for the long-term and productive operation of the device.

How to adjust the carburetor of the STIHL motorcosa

lawn mowers, like the entire bench tool for the garden, is not difficult to maintain equipment. Repair, configure without the help of others you can and necessary. For example, adjusting the carburetor of the lawn mower with your own hands. it is 5 minutes.

The carburetor from the lawn mower is a node in the power supply system. In it, like all carburetors, there is a process of mixing air and fuel (gasoline) for the upcoming supply to the motor cylinders.

In this process, the main thing is the correct proportion of fuel and air, why the carburetor is regulated.

The main problems and malfunctions of the carburetor.

Mesh filter. There are only two difficulties with this element more often:

In order to find out the cause of the breakdown, the fuel filter lid is unscrewed to extract the mesh filter. If the mud just accumulated on it, then flushing in gasoline or purge will help.

With visible damage on the mesh filter, it is necessary to put a new. There may also be damage to the fuel supply pipe (during the repair they practice checking this element).

The starting device of the carburetor in most cases does not work due to blockages. Should be used for flushing acetone or the same gasoline.

Purging parts of a carburetor with click of compressed air. permissible and comfortable repair practice.

replacing, carburetor, stihl, station, seals, fs38

The hull of throttles, places of ligaments of the parts of the carburetor, intake or graduation pipeline. all of the listed parts are subject to depressurization. You can probably check the simple method. spread the problem area with soap foam.

The device of the carburetor of the lawn mower

The base of the carburetor of the lawn mower. the duralumin case. It contains a diffuser (a hole with internal contours). Air is pumped through this hole. The speed of oxygen (air) is dependent on the cross.sectional (passage opening) of the diffuser.

Diffuser is equipped with fuel channels. How to adjust the carburetor to adjust the carburetor motorcosa in practice. video. Fuel is drawn from them using a stream of air.

The principle of operation of the carburetor of the lawn mower

The throttle dashes determines the amount of air for supply, and the power of the motor directly depends on this.

STIHL FS 55. Carburetor adjustment (idle)

The trimmer for herbialhl fs 55 in the video is executed with the aim of making the momentum of idle.

Adjustment of the carburetor lawn mower Stihl FS 55

Adjustment of the carburetor lawn mower Stihl

FS 55 Sadservice Sadservice Sadservice Spare parts.com.ua.

A combustible pump (its membrane) is sucked into the carburetor system. Carburetor Motokosi then passes through a fitting in a carburetor. Then the liquid moves through the intake and exhaust valve of the pump. Filtered with a net. On the needle valve moves into the membrane chamber.

  • Air supply to the tube with an air septum (damper). The partition regulates the intensity of the air flow.
  • The fuel supply system is certainly narrowed by the mixer to accelerate the flow.
  • Gasoline through the float chamber and nozzle with narrowing. The chamber with a float regulates the temporary volume of gasoline. In the float chamber, the pressure level is neutral, and in the tube with narrowing is already small. Thanks to the pressure drop, fuel seeps through a jickler.
  • Acceleration of the air flow contributes to the transfer of fuel (gasoline) and its spray. Ultimately, a fuel mixture of the desired proportion or density appears.
  • The air-fuel mixture penetrates the motor cylinder through the fuel tube.

Read Stihl 250 Carburetor adjustment video

The level of air density in the system depends on the area of ​​the open air damper. The more extensive the damper is open, the greater the fuel consumption and power.

Simply put, adjusting the carburetor on a benzocos. creating a good fuel consistency due to the correct air supply.

How to adjust a carburetor on a gas tank

Before adjustment, you need to painlessly clean the filters according to maintenance in the annotation.

The upcoming setting of the carburetor of the lawn mower with your own hands is made by adjusting screws. There are three of them:

Right (l). adjustment of the fuel consistency for low revolutions.

It is necessary to find the highest speed at idle. To do this, leisurely twist the screw (l) on the right and on the left.

For adjustment, the screw is rotated by a quarter of turnover by all means counterclockwise.

Lower (t). is responsible for adjusting the motor at idle.

For proper adjustment specifically, the idle move is typical:

  • sustainable work of a cool motor;
  • not high speeds of a hot motor;
  • for a trimmer head, there is a lot of revolutions;
  • Sustainable work of the motor when changing the position (sharp rise or descent of the knife).

Read Carburetor Adjustment to 45 Motoboglok Agro

Left (H). adjustment of consistency at high speeds. (The screw is set up last).

The overall adjustment of the highest revolutions, the power of the motor, temperature and gas consumption depends on the left screw (H).

Setting a carburetor of a lawn mower with the last screw is carried out as follows:

  • Open the throttle to the full, at the same time give out full gas. Turn the screw clock until the time until the speeds fall (in this case, they are oriented by ear).
  • Turn the screw as slowly as possible against the hourly to the uneven operation of the motor.
  • Then turn back at all, hearing a little measured, even work.
  • For a more pleasant implementation of abilities, it is more convenient to discern the work of the most experienced user:

It is curious that based on the beliefs of the creator of the video, the configuration (its correctness) is determined by the color of the candle, and not just by the turnover and stability of the motor.

True tuning the carburetor with your own hands in this case-combustion of the fuel consistency without a residue, the color of the candle should be light brown.

Caliber company. Brand’s base and popularization

Enterprise OJSC Caliber was founded in 1932. From the very beginning of its appearance on the market, the company aimed at the production of high.quality and inexpensive economic and industrial equipment. During the war years, the company’s plant provided production services: sharpening the tool, as well as turning, milling and heat processing of parts for Soviet weapons.

Today, in the assortment of the company you can find electric and gasoline equipment for home and garden, as well as operating machines in production. Gasoline and electric trimmers for grass are very popular among brand products. They are distinguished by high reliability, modest consumption of fuel and electricity, as well as stability during operation in severe conditions

Another important advantage is low for brand technique. The correct pricing policy of the company makes it possible to purchase its products to almost everyone

Description of the model

The Stihl FS38 Lawn Mobilum. the easiest mobile version with a capacity of 0.9 liters.With., It is intended for domestic use.

  • Thanks to the modern electronic ignition system, reliable starting and uninterrupted engine operation is ensured.
  • Using the fuel pump, the operator has the ability, if necessary, pump up fuel into a carburetor.
  • Optimal maneuverability is provided thanks to the D-shaped handle, with which it is convenient to control the Stihl motorcycle carpet when working in complex areas.
  • All control levers are located on a special multifunctional handle (R), which ensures the safety and reliability of the benzotrimer operation.
  • Thanks to the Autocut C5-2 mowing headset, the diameter of the mowing is 380 mm.
  • The ergonomic shoulder belt allows you to hold the STIHL motorcycle cub on the shoulder, it is rational to coordinate movements during operation.
  • Small mass (4.1 kg.), small dimensions, rational basic equipment. thanks to these characteristics, the Stihl 38 lawn mower is extremely comfortable in work.

The design of the device

The essence of the device is to transmit torque from the power drive. gasoline, electric or battery, to the cutting tool. a knife or fishing line. The transmission mechanism is the shaft located inside the bar. In devices with a curved shaft, its role is played by a steel cable.

The bar is fixed to the drive gearbox- two- or four-stroke. When you turn on the torque, a fishing line or knife is transmitted by shaft.

The most difficult part of the device is the motor. Damage to the shaft, belts, cutting tools are attributed to breakdowns mechanical, but the repair of the engine of the lawn mower usually causes difficulties. Part of the malfunctions associated with contamination of engine elements can be eliminated independently. It is better to entrust the replacement of spare parts or setting up to a specialist.

Repair of a trimmer for STIHL grass with your own hands and operating instructions FS-38 and 55 (STIHL FS), carburetor adjustment

It is inherent in a person to ennoble the place in which he spends the lion’s share of his time. Residents of cities resort to the services of designers, or they themselves try to change something in their home, buy new furniture, wallpaper, so that, having arrived home after a difficult day, one could mentally relax and relax in a favorable atmosphere. Residents of their own houses behind the city line have completely different worries and demands. It is necessary to download shrubs, grass, various dryness, carefully monitor the state of the personal plot and garden. It is clear that this requires slightly different means of achieving comfort. And then a new brainchild of engineering thought comes to the fore. STIHL mowers of the company.

Hi Dear friends! My past post for repairing a chainsaw has collected many questions, many answers and 150 subscribers. I continue to dilute the community of repairs of benzo-instrumentation. In one commentary, they asked to show how to change the oil seals not with a stihl gas station, just I had to repair the Stihl FS55, the instruction is also suitable for Stihl FS38/44.

So, we went, the preface: the lawn mower was brought to this before the upcoming season, she started, worked, and only occasionally there were not big problems with long work, she began to live her life, did not obey the pens of gas, but it soon worked and she worked again.

Carry out that (replacing filters, candles, lubrication of bearings, cleaning, purging, adjustment). show how I will not be done, everyone should know this.

Find a defect that causes “your life” of the lawn mower.

Near the carburetor and under the lids, dust was visible, the carburetor and the inlet tract was completely serviceable. So we will get to the seals. To do this, remove the starter.

Then we unscrew the screws below the braids for the grass that are marked.

Remove the casing of the upper and lower. Next, we take the suitable torx in size, insert it into the clutch drum and twist it, the right carving, that is, the usual.

Next, the clutch pads go, if there is no pneumatic control, then we pinch the flywheel carefully in the vice through wooden spacers, and unscrew the gas key, the right thread is right.

If the flywheel itself does not fly away, then we take the kiyanka and slightly beat it, it is easily removed, from the side of the header, the head of the starter’s ratchet, the right thread, is right.

So we got to the oil seals, visible around them oil with dust, so the seals are missing, the client said to change.

We pull out the old oil seals with a thin screwdriver, we clean everything, we take new oil seals (size 12227.3, these are on China with 26 and 33cm3 braids), lubricate with oil and inside, fill the suitable head.

We collect everything in the reverse order. I launched it, heated, gazed, works like a clock.

Carburetor cleaning and adjustment, gear lubrication 300r

I do not praise Stihl, but I asked how long this braid for the grass has and how much it mows, a braid for herbs is 5-6 years old, in the summer it harvests hay, it mows 3-4 days a week, burns up to 5 tanks with interruptions only for refueling.

Quick launch of the lawn mower: tips

Some pull the pen with such force that it is necessary to repair the starter of the lawn mowed with their own hands. This is possible only in the case of a gust of a cable or breakdown of the cable handle. In other cases, it is recommended to replace the starter. This node is sold in the collection.

Adjustment and repair of the carburetor of the lawn mower

The trimmer for grass does not apply to complex household appliances, because most of its breakdowns are mechanical and are quite successfully eliminated with their own hands. Even if the motor refuses for severe reasons. damage to the piston ring, for example, the repair is reduced to the substitution of the part.

And with a relative design, such a device of the device as a carburetor needs to be adjusted.

How to adjust a carburetor on a gas tank

Before adjustment, you need to painlessly clean the filters according to maintenance in the annotation.

The upcoming setting of the carburetor of the lawn mower with your own hands

It is made by adjusting screws. There are three of them:

Right (l). adjustment of the fuel consistency for low revolutions.

It is necessary to find the highest speed at idle. To do this, leisurely twist the screw (l) on the right and on the left.

For adjustment, the screw is rotated by a quarter of turnover by all means counterclockwise.

Lower (t). is responsible for adjusting the motor at idle.

For proper adjustment specifically, the idle move is typical:

  • sustainable work of a cool motor;
  • not high speeds of a hot motor;
  • for a trimmer head, there is a lot of revolutions;
  • Sustainable work of the motor when changing the position (sharp rise or descent of the knife).

Left (H). adjustment

consistency at high speeds. (The screw is set up last).

The overall adjustment of the highest revolutions, the power of the motor, temperature and gas consumption depends on the left screw (H).

Lawn mowers with the last screw are done as follows:

  • Open the throttle to the full, at the same time give out full gas. Turn the screw clock until the time until the speeds fall (in this case, they are oriented by ear).
  • Turn the screw as slowly as possible against the hourly to the uneven operation of the motor.
  • Then turn back at all, hearing a little measured, even work.
  • For a more pleasant implementation of abilities, it is more convenient to discern the work of the most experienced user:

It is curious that based on the beliefs of the creator of the video, the configuration (its correctness) is determined by the color of the candle, and not just by the turnover and stability of the motor.

Electric trimmer for STIHL FSE 71 grass. advantages and opportunities

This model is equipped with a durable electric motor and is designed to actively use to care for the house territory. The trimmer for grass is released by simplicity in everyday use, modest weight, excellent build quality.

The model is equipped with a strong metal handle with rubberized handles. All the most important tools of the tool are made on the right handle of a trimmer for the grass. For convenience during operation, the manufacturer equipped the tool with a convenient shoulder belt.

The main factory parameter of the model includes:

  • The power of the standard motor is 540 watts;
  • The maximum possible capture diameter when using fishing line is 36 cm;
  • capture diameter when using a knife. 16 cm;
  • working form. 4.3 kg.

STIHL trimmer in this configuration is equipped with a rotor.type cutting system. It is distinguished by endurance, high suitability for repair and resistance to mechanical damage.

complex reasons for the refusal of the lawn mower

If the step-by-step algorithm for searching for a malfunction has not given a result, and your braid for grass still does not start or stalls, it is worth examining the carburetor and the engine itself. A clogged carburetor can become one of the reasons, unstable operation of the tool. Three main problems can be distinguished here:

replacing, carburetor, stihl, station, seals, fs38
  • Clogging of channels or nozzles. All this is cleaned with special flushing or blown by a powerful stream of compressed air from the compressor. Do not use needles and wire, so the passing sections can be damaged;
  • Wear of the carburetor laying. Output. replacing the failed laying;
  • Violation of tightness. To check this indicator, you can use the usual household tonometer, replacing the pressure gauge on it with the right. Follow the testimony: if they do not change, everything is fine, and since the pressure will begin to fall, then some part of the carburetor is faulty. Will have to find it and replace it with a new.

If everything is in order with the carburetor, then the gasoline trimmer for the grass may not be launched due to wear of the piston group. If chips, scratches or bully are found, on the piston or cylinder they should be replaced. Piston rings are subject to mandatory verification. A small rally piston when swaying the connecting rod indicates that the time has come to change the rings. This procedure is best entrusted to the specialists of the service center.

Operation Rules for Motokos STIHL FS 130

To extend the operating time of the STIHL motorcosa, its owner should adhere to a number of important rules.

  • mandatory running.in before starting the operation of a trimmer for grass;
  • the use of high-quality gasoline and corporate oil for 2-stroke engines;
  • the use of effective oil for lubrication of the gearbox, its timely replacement;
  • avoiding shock when working with a trimmer in an open territory;
  • regular cleaning of the cylinder and adjusting the carburetor;
  • Timely flushing or complete replacement of air and fuel filters.

Compliance with these rules reduces the risk of untimely breakdown of the mechanisms of StiHL motorcosa and gives its owner the opportunity to save on consumables of garden tools.

Where to start diagnostics motorcycles

If the lawn mower does not start or immediately stalls after starting, it is necessary to sequentially check all the main nodes and assemblies. The test algorithm is as follows:

  • Fuel tank (fuel quality);
  • Candle and candle channel;
  • Air filter;
  • Fuel filter;
  • Breather;
  • Graduation channel.

These nodes are most often source of basic problems, which can be eliminated after a thorough inspection.

Check the fuel mixture

Before starting the engine of a gasoline braid for grass, check the presence, and the quality of the fuel mixture. Do not save, do not greedy and “do not smarter” in this matter. Repair or replacement of the piston group will cost you too much (sometimes up to 70% of the cost of a new tool). Prepare the oil fuel mixture strictly according to the instructions. Calculate its number from real needs. Excess gasoline left after work loses its qualities over time.

We diagnose a candle and candle canal

If the quality of the fuel mixture is not in doubt, and the lawn mower stalls when starting, then a flooded candle may be the reason. Here, a regular candle key is suitable for repair (every motorist has probably has a spare candle.

  • We twist the candle and wipe;
  • We thoroughly dry it (you should not bake it);
  • Excess fuel in the chamber we drain through the candle hole and dry it;
  • We clean the old candle from the carbon on a sugar or a ladies’ file;
  • We set a gap with a distance of 1 mm (you can check with any coin);
  • We return everything to place and try to start a trimmer for the grass.

If the working candle is working, the nest, where it is located completely dry, and the lawn mower does not want to start, lubricate the threaded connection with gasoline. It should be slightly moisturized. No matter what wonderful spark gives out a candle, there is simply nothing to light up in a dry chamber.

If the trimmer engine for grass still does not start, such a cause as the lack of spark due to weak contact between candles and a high-voltage wire should be excluded. If the connection is of high quality, and there are no sparks, most likely, you have “flew” the ignition unit. Here you can’t do without a master, t. to. The part is not repaired, but sold by a whole knot.

Diagnosis of the filters of the lawn mower

Another reason why the gasoline braid for grass stalls is an air filter. To exclude it, try to remove the filter and start a trimmer for grass without it. If it turns out, then you will have to change the air filter to a new one, or at least blow and carefully clean the old.

You can’t start a gasoline trimmer for grass due to contamination of the fuel filter. This is the next stage of our algorithm. Here we check the state of the filter element and, if necessary, change it with the new. When replacing, try not to leave a suction pipe without a filter, this is prohibited by any operating instructions. Rush can turn into the repair of the piston group of the engine.

Sapun and graduation channel

Often, “delicate” branded models of benzos are not launched and stall due. The main function of this element is to align the pressure in the gas tank. When clogging this node, a vacuum is created in the tank that prevents the supply of fuel. Eliminate the malfunction can be cleaned by cleaning the sounds. You can use a regular needle for cleaning.

The normal operation of the cos with internal combustion engines can be disturbed due to the entry of dirt into the exhaust channel or clogging of the muffler grid. There is such a problem on the models of the older generation. You can solve the issue with traditional cleaning and removal.

Conclusions and results

As a result of our review, we found out that for a buyer with a small area (5-7 acres) and a small budget, the FS 38 lawn mower is best suited. And for connoisseurs of econsmicity and environmental friendliness, as well as more modern technologies. the FS 40 lawn mower. Dachants and gardeners with areas of over 7 acres, in 80% of cases, will be selected by FS 55 or FS 55C, since it is equipped with a gearbox, a bicycle pen and a background belt, which will help to cope with higher grass and hard shoots on large volumes.

Professionals or utilities will prefer gasoline braids for FS 120 and FS 250 grass, as they are equipped with a powerful engine and are relatively inexpensive. They are also equipped with a hard shaft for installing a all kinds of cutting and sawing sets, and are suitable for large volumes of work. These trimmers for grass will cope even with small trees, shrubs, reeds.

For the most selective and demanding buyer, STIHL can offer gasoline braids for grass with 2MIX and 4MIX technologies, with a multifunctional handle and a comfortable launch system that meet the highest European standards. Such as FS 70 (for small volumes of work) and FS 131 (for large volumes of work).

We wish you successful purchases and long years of service with STIHL gas troops! Do not forget about annual free service benzos STIHL!

| Denial of responsibility | Contacts |RSS