Is it possible to saw a corner grinding tree tree? Secrets of specialists, how to do it right

Greetings, my dear readers of the blog Andrei Noac. Many people ask the forums the question is whether it is possible to cut boards with a corner grinder? Therefore, I decided to fully understand this issue with you.

Corner type grinding machine. universal tool. The corner grinder is suitable for a whole spectra work, replacing a number of metal tools, often performing the work even better and more precisely. This can boast of all the processes produced by the metal disk. But how are things with wood and a wood-piece plate? Is it safe? I want to figure out today how to do it at my own peril and risk.

Advantages of using corner grinding selipshois to work with wood

The tool has a powerful engine, which allows it to easily cope with all breeds used in domestic housing construction and production. As a rule, we are talking about working with a beam, board and woodworking blanks. Even the minimum power of 500-700 watts will be enough to process standard lumber. But here another question arises: “Is it possible to cut a tree as such or logs or logs?»This will depend on the size of the nozzle, but it is in solving such problems that a chain saw is more likely. The corner grinder, in addition to performance, justifies itself in terms of functionality. Modern compact models weigh a little, but at the same time have a wide set of systems for adjustment, safety and management of equipment. The operator can individually configure the device in the depths of the cut, the number of revolutions, use the soft start and other possibilities.

Varieties of disks for corner grinders: the most suitable wood circles

The range of nozzles for this tool is quite wide. Products are classified for its intended purpose, depending on what you can distinguish 3 main groups of circles for angular grinder:

Corner grinder disks are divided into three categories: abrasive, saw and diamond spraying

Saw. Have similarly with standard saws, but are produced from other materials. The most common option is the tungsten carbide wheels. They are not suitable for working with wood.

With diamond spraying. This group of circles for corner grinders is the most extensive. The high popularity of nozzles with diamond spraying is determined by a wide operational spectrum. Using such circles, you can process metal parts, as well as elements of stone and concrete. For wood, such discs are not used.

note! The use of corner grinding lifmash requires compliance with some rules. One of them claims that it is impossible to use circles of larger diameter than indicated in the device passport.

For wood processing, abrasive discs are best suited

Abrasive. They are distinguished by high versatility. Abrasive discs are used not only for cutting, but also for grinding, as well as polishing surfaces. Products from this group are also used for wood processing.

These products are differentiated by one more basis. dimensions. The modern market provides a wide selection of products, the dimensions of which vary in the range from 115 to 230 mm. A wood.grinder wood disk is 115 mm in the most compact and is used for quick and accurate cutting of the material. It is worth noting that the largest discs are not suitable for working with wooden surfaces.

Types of wood disks for angular grinder: design options

Many experts do not recommend using a corner grinder for cutting and processing wood. This is due to the principle of operation of the device and the characteristics of the material itself. However, the variety of disks for angular grinding grinding is growing every year. They can be divided by the features of work into several types.

Circular saws. Such woods for corner grinder are used, as a rule, for more technological equipment, but many install them on an angular grinder. They are divided into two types: large diameter with attacks and more compact, without attacks.

Segment discs are made of carbit pholphrama, which is characterized by high strength

Chain. Ideal for working with wooden materials. Many people are interested in the question of whether it is possible to saw a corner grinding tree tree. There is no unequivocal answer to it, but chain products are maximally adapted for this purpose. The edge of the circle in this case is equipped with a chain on which the teeth are located. A similar design has many advantages. This nozzle is most often used to perform a flat cutting of the board. With the help of it, you can process other materials: wood-cutting plate, wood-fiber slab, plywood.

Small dental saws. This variety of circles was invented specifically in order to ensure maximum security of a person when working with wood. Compact products related to this group have 3 teeth, and more overall. 4. This group also includes cutting wheels for corner grinding grounds 125 mm. Such products do a great job of their functions. They can be used to cut wood along and across the fibers. In addition to standard functions, such discs are used to organize grooves in the workpieces.

Segmented (material-carbide-wolfram). Such products appeared relatively recently, but have already gained immense popularity. A distinctive feature of such products is the absence of teeth. The edge of the disk consists of segments that are characterized by high strength.

Wood wheels are divided into chain, circular, segment and nozzles with a small number of teeth

Useful information! With the help of a segment nozzle, you can work with wood of any strength and viscosity. It is characterized by high safety and is able to withstand even metal inclusions present in some blanks (self.tapping screws, nails, etc. P.).

Wood chain saws: Advantages of use

In this case, the saw circle is made using a chain from a chainsaw. Such a nozzle is the most acceptable for working with wood, as it has the greatest efficiency. The chain wooden disk for corner grinder is also considered the safest. The use of this nozzle significantly reduces the likelihood of an injury if the tool jams.

If the disk falls on the solid element of the tree during operation (for example, the knot), then the chain is not destroyed. This occurs due to the turning of the basis. Such nozzles are very popular when it is necessary to clean the tree trunk from bark and knots.

Chain saw discs are considered the most suitable for working with wood

Wooden wood wheels for angular grinding with a chain are used for all kinds of works. With the help of them you can remove branches of trees, as well as cut boards of small thickness. The functional capabilities of chain products allow them to use them as peeling tools. They do a great job of removing the bark.

With the help of a saw circle, you can perform a smooth cut of a parquet board, plywood, wood-fiber slab, a wood-boring plate, as well as ordinary non-cut and trimmed wooden products. It is important to remember that the thickness of the material that will be processed by such a nozzle should be no more than 4 cm. Otherwise, there is a high probability of overheating of the device.

Cutting methods of laminated wood-bruise without chips

You need to saw a laminated board with a special machine (formato-sprinkler). But it), if we are talking about use at home. The alternative can be budget options (hacksaw, jigsaw, etc.D.) that will take more time when cutting, but will require less monetary investments.

Using a hacksaw

with a hacksaw at home it is quite difficult. First you need to cut a fishing line for a trimmer for measurement and glue the tape along it. This will protect the upper layer from damage. The tool is directed at an angle of 30 degrees. Gently, without strong pressure, move the hacksaw forward and backward. To cut a manifested wood-brown stove without chips with a hacksaw at home, choose devices with the smallest teeth. In case of damage, the cut place must be passed by a file, directing it from the edge to the center. In the end, rub with sandpaper (fine.grained) and hide defects under a flexible profile.

Read checking the gas.rosopyle ignition coil by multimeter

Rules of sawing

Before sawing, choose a method, as well as accessories and tools.

  • scotch;
  • painting tape;
  • pencil, ruler;
  • sandpaper.
  • hacksaw;
  • milling mill;
  • a circular saw;
  • tire;
  • jigsaw;
  • cutting machine.
  • On the end of the wood-brown plate, apply points. It is necessary to determine in advance what type of cutting will be produced. a straightforward or figured. The technique of cutting is different from them.
  • Connect the points into a fishing line for a trimmer and stick a sticky tape on top. Drinking a chipboard with a laminated coating is desirable using adhesive tape. It will reduce cracks when cutting, since a wooden plate is subjected to severe pressure with an increase in temperature.
  • Cock the board. The accessory is installed at the right angle to achieve extremely even edges. The process should occur smoothly, rhythmically and without strong pressure.
  • Irregularities and edges, if necessary, process a file and rashpil. The edges can be glued with veneer corresponding color. This will provide them with protection and will look more beautiful.

Only after the location of all the necessary tools on the table can you start the saw.

With the help of a cutter

Fraser. power tool for manual wood processing. Suitable for cutting grooves, curly processing, edges and drilling. Before using it, a tree sheet is sawn with a jigsaw, retreating 3 mm from marking. It is necessary to cut the milling cutter along with the bearing, which form the cut depth to the required level. This is a laborious process, only experienced specialists can do. High probability of crookedly cut off the board.

Electric

To flatterly sawn down the wood-bruise plate without chips, you need to choose a device with a minimum size of teeth. It is used for small areas of tiles, smooth movements without pressure with low speed. If you use a jigsaw for the first time, then a little crack may appear on the back of the plate. With further use, the quality of the saw will improve.

Drinking with cutting

For the process, a tire is needed. a stubborn ruler. It is fixed on the board with clamps. Trimming is carried out according to the markings. The tire is installed on a mowing fishing line, and the gap is made by 10 mm deep. The second cut is done through and through. With this method, there will be no chips on both sides, since the laminate is already cut on the bottom.

Some elements used in design ideas are cut not straightforwardly, but curvoline. In this case, the mixed type of cutting wood slab is used.

Cut a format-sprinkle machine

The workpiece is installed on the table and fixed in a stationary state. The necessary markings on the sheet are made and the saw node includes. When the disk reaches sufficient speed, the table moves forward with wooden slabs and gets to the disk

Wood-and-based cutting machines are divided into 3 types:

  • Stanin. a mount on which the entire mechanism is based. A heavy bed will add stability to the device and eliminate vibrations. This is important for high.quality sawing.
  • Saw node. consists of 2 flat metal disks. The first preliminarily cuts the stove, and the second finally cuts it through through.
  • Working tables. Three at once take part in the process. The first is for the location of the node, the second. for the supply of drunk plates (mobile), the third. to maintain sawed parts.
  • Carriage. allows you to move the moving table. In this case, the workpiece is fixed using the emphasis and the rulers in the necessary position.

Reception 1. Sprinkled along the guide

Install the guide (tire) on the workpiece, set the depth of sawing and perform a cut. As you yourself can be convinced, even on the outside of our workpiece made of wood-bearing plate, no chips, there are no undermining. He drank even without signs of bully or lateral waves. Why such difference?

How to bend the wood-brown slab-practical aspect

Sometimes it is necessary to make a bent part of a wood-mounted stove-the end of the table, cabinet, shelves.

Для этого нужно вначале вырезать по размерам необходимый фрагмент материала, после чего выполнить многочисленные параллельные пропилы на его внутренней поверхности (см. рис. 1 и 2)

Necessary fragment of sawing

To give a curved form, the resulting part should be glued to the template by PVA glue and fixed with self.tapping screws. After withstanding the time required to harden the glue, the part can be removed and used as intended.

Before screwing the screws into the woody stove, it is advisable to drill the material in advance. For this, drills are used 1-2 mm smaller diameter than self-tapping screw. Drill for wood-brown stove are used the same as for drilling wood, and standard screws are bought by standard.

Due to the lower cost of wood-based sheets than other installation and building materials, a small amount of marriage when working with your own hands is not a critical. Spoiled sheets can be used to manufacture smaller products in size, not incurring the costs of attracting professional equipment and specialists.

We recently bought a coffee table, the price is inexpensive, but there is “but”. The height of the table for our interior is big. It would be nice to reduce the height of 10 centimeters by 10. As they say, we are not looking for easy ways, I decided that

I remembered that on our website there is an ASOLEG specialist who did. I, of course, are far from it, but some recommendations can help. Contacted him, explained the problem and kindly shared his secret. With his permission, I publish his technology cutting a furniture wood-bearing plate without chips.

Drinking laminated wood-bruise without chips. Magic zero liner! Announcement

Everything turned out to be banal simply. We mark a fishing line for a cutting cutter. Then we cut through the top layer a wood-mounted stove with a chancellery knife, along the ruler. We just spend with a knife several times with a little effort on the mowing fishing line of the cut. (I recommend that you practice on the unnecessary part of the chipboard wood) if you press very strongly, then the decorative layer will begin to swell and it will not turn out very beautifully.

Next, retreating 1-2 millimeters from the intended mowing fishing line towards the draft part, cut it with a jigsaw or a suitable file with teeth aimed at the saw handle. We make a cut on the opposite side of the cut so that the chip does not occur at the end of the cut. And we drink it to the end. To saw

How to cut a laminated woody stove

Laminated wood-bearing plate can be sawn with a hand saw with a small tooth, an electrician, a disk saw. The cut place is glued with masking tape and cut out along the cut line with a sharp knife. The knife cuts out the laminated coating and the upper wood fibers under it. Further, when passing with a saw with a saw, a laminated wood-bearing plate will not be cooked. The finish of the end under the C-shaped overhead kant in the manufacture of furniture, this method is quite suitable. And it is better to use a different way under a melamine self.adhesive tape.

Electrolobsik or disk saw saw a laminated wood-brown stove with a margin of 2-3 mm. From the cut line. I sawed an electrician on the guide. As a guide, you can use any even rail or rule. In my case, fiberglass 150 mm wide. The thickness is 4 mm. As described above, chips were formed on a laminated wood-based stove. Next, set the guide exactly along the cutting line and with a manual milling milling milling cutter we remove these 2-3 mm. which we left for stock. The design of the bromic milling cutter has on the shank bearing equal to the diameter of the cutter itself.As a result, we get a perfectly even edge, to which you can easily glue a self.adhesive melamine tape. Also, when cutting curved cuts, you can not do without the use of the milling cutter. We make a guide with the desired radii with an electrician and also pass the end of the bromatic milling cutter. The method of cutting laminated wood-bruise without chips is also suitable for cutting laminated plywood and wood-fiber slab.

In general, I have already examined this in a review article, which was devoted without the use of a format-sprinkle machine.

Today I decided to dwell in more detail on the method available to most homemade drivers. this is a sawing by an electrician, since this tool is very widely common. In this lesson, I used Skill 4581la household electric. By the way, a very good machine.

For the highest quality cut, the following conditions must be met

In addition, for the greater purity of the cut, we will use such a modification as sawing “on scratches”. Its essence lies in the fact that the laminate is scratched to the entire depth and its pieces pulled out by the teeth of the files, the scratches do not go abroad. For clarity, I will give several photos.

It is necessary to scratch the ruler (any sharp object-I used a drill-perca, or at least a self-tapping screw.) So that the ruler does not shift during the scratch process, I additionally fixed it with a clamp. you can a couple.

Scratch to the entire depth of the laminate, that is, before the appearance of sawdust in the scratch.

Then we take the jigsaw, and we lead it so that the saw goes as close as possible to the edge of the scratch, while without leaving, beyond this border.

Thus, chips are formed only on the unnecessary side, without going beyond our marginal fishing line for a trimmer

Once again, the same cut at its completion. It can be seen that the minimum chips still remained, although they can be on professional equipment. But the evenness of the cut leaves much to be desired.

Of course, there are unique ones that can saw an electrician quite evenly. I don’t belong to this. Of course, the class of the tool itself also plays a significant role. As a rule, in inexpensive tools, the saw is not as stable as in professional models. Due to this, it takes it towards the sawing.

In general, this method has the right to exist, but I would not advise putting it on a stream.

As practice shows, to make a high-quality cut of a wood-piece plate with a durable melamine coating is very difficult. Rough tools often leave Zazubrins on the sections. A neat door or shelf with such defects can no longer be collected. The laminated wood-boring slab at home, as a rule, was cut during repair work or furniture.

How to cut a laminated wood-bruise plate without zazubrin and chips?

Milling with grinder

Another operation, which many experienced masters successfully use with this tool. Milling. Unlike milling, it is impossible to perform a really high.quality finish. However, make a groove, as well as cut a small part, will be quite tolerant.

Again, this operation is dangerous. I have already written recommendations for general actions with this tool, so just follow them. The grinder needs a thick and high.quality cutter. Immediately give up the ability to use homemade nozzles, give your choice to the old brand insured by chips and breakdowns.

Even using all the tips, a beginner should not engage in milling on their own without a more experienced master. As mentioned above, accidents constantly happen to the masters of their field, given the instrument instrument.

Tools and equipment for sawing

Depending on the volume of upcoming works and the saw configuration, they use:

Not every tool can get details of the required form.

Formato-sprinkle machine

If the exact sizes are known by which the sheet should be cut, it is more correct to entrust the work to professionals. Almost all sellers. bases and building materials. provide such an option. Often the sawing service is free, the customer pays only the cost of a wood-piece plate.

For cutting, format-sprouting machines of various designs are used.

Sprinkle the wood-brown slab without chips allow various additional devices. For example, some models have two sawing disks: the first, small diameter, drinks a surface laminated layer, and the main carries the full cut.

CNC format-sprouting machines operate in a semi-automatic mode, excluding the operator’s errors, which allows you to get ready-made parts with an exact size of up to 1 mm. This is important in the manufacture of cabinet furniture.

Lobby

A sheet is cut by an electric jigsaw on straight and curly lines.

  • Availability. Most masters have a jigsaw, and the new one costs inexpensively;
  • On sale there are special files for a wood-piece plate, laminated wood-bearing plate and laminate;
  • You can cut circles with a small radius;
  • Suitable for the manufacture of through holes for hatches or electrical products.

To obtain a rectilinear cut, you must have experience working with a tool or just use the guide tire.

Parquet

A manual disk saw, sometimes called a “parquet”, is used if there is a large amount of work on the cutting of the wood-piece stove along the even lines.

Acquire wheels with carbide tips of teeth.

To simplify and accelerate the work, they choose a parquet, complete with a guide tire or buy an accessory separately.

You can do without additional details if you lead a cut along the guide from the corner or plaster rule.

The main drawback of the method is the inability to make a curved incision.

Milling mill

To qualitatively saw off the wood-making slab using a milling cutter, the master needs extensive experience.

A flat, impeccable edge is obtained only when using diamond mills, the price of which is large.

At home, a milling mill is often used to finish the edges of the laminated wood-based slab. In these cases, the sheet is sawn with a hacksaw, a jigsaw or a disk saw, and then the cut is treated with a milling cutter. It is important to provide a stock of 1.5–2 mm, which will be removed by the milling.

Hacksaw

The cutting of hand hacksaws takes a lot of time and requires a large cost of physical strength.

Hand saws with a large and medium tooth are suitable only for sawing a conventional wood-based slab (without a laminated layer). The result will always be accompanied. The appearance of the edge can only be fixed by decorative lining.

A small cutting volume is performed with a hacksaw with small teeth. To reduce the number of chips, launch tape is glued over the sheet, mark the fishing line for the cutting trimmer and only then begin to work.

Despite the fact that the seats of the saw wheels for parquet and an angle grinding machine may coincide, cut the wood-boring plate and a tree with a corner grinder is strictly prohibited. The torque of even a weak machine will tear out the tool from the hands, and the disk will cause injury. The danger is that rotation cannot be stopped instantly.

Stages of work

Using an electric jigsaw is the most common option for sawing a wood-brown stove at home, due to the availability of tools, universalism and simplicity of circulation.

Requirements for used files:

In the assortment of most tool manufacturers there are special products for sawing wood stove. Files for laminate are also suitable for work.

The process of sawing consists in the sequential performance of three operations: marking sheets, sawing and processing the edge if necessary.

Cutting out the material

When homework, it is important to correctly carry out the cutting of the material in order to minimize the amount of waste. Particular attention is paid to the “layout” if the laminated wood-brown plate has a clearly pronounced pattern, which must be taken into account.

It is recommended to plan the location of the parts on a sheet of paper. On the Internet, it is easy to find calculators and programs that automatically plan the optimal location of parts.

Before starting work, it is necessary to lay the sheet on a solid basis, taking into account that the site of the cut is needed a supply of free space for the progress of the file.

Further, the cutting algorithm consists in the sticker of the painting tape and the drawing of the sawing lines with a permanent marker.

Having glued the masking tape of the required width, it is possible to exclude scratches from the steel sole of the electrician, reduce the likelihood of chips of the laminating layer.

If it was not possible to find special files for the wood-cutting stove, the sawing is carried out on the back, so that the teeth “work” towards the surface.

The process of sawing

It is recommended to saw with the help of guides with even lines.

The work algorithm is as follows:

  • A layer of laminate is cut through a sharp knife or a special tool. The operation reduces the number of chips.
  • With clamps, the guide is fixed, about which the sole of the jigsaw will be based on a direct cut. You can do without device if the quality of the edge is not decisive or with extensive experience. The location is chosen based on the width of the supporting plate of the jigsaw.
  • Set the average rotation of the electric motor, remove the rolling mode.
  • Start drinking from edge to center. The instrument pressure is excluded, since in this case the file will definitely take aside or the cut will pass at an angle in the plane of the sheet.
  • If necessary, they carry out finishing, bypassing the workbench.
  • At the end of the drink, the sheet is excluded under its own weight.

Only high.quality files allow you to work for a long time. The Economy Class tool will ensure cutting out no more than 5-10 linear meters of laminated woody stove, after which the teeth dull chips, the jigsaw leads to the side.

If you need to cut the inner hole under the hatch, installing electric sockets or switches, first mark the marking. Next, drill a wood-boom slab with a drill 1-2 mm exceeding the width of the file. Having set the file in the formed hole, the sawing is carried out.

Processing after trimming

If you use hard profiles, = just remove dust. Playing is carried out with carpentry glue.

The end of the end of the end is carried out with films of different material:

disk, stove, corner, grinders, wood-piece, chips

An important condition-before glitting, it is necessary to align the end surface of the wood-bearing plate.

For processing, use a milling mill, file or a grinder.

Self-adhesive films are pressed by any even bar. After gluing, the protruding parts of the end tape are cut off.

Features of the choice of disk for wood

Circles for corner grinder are made standard sizes. Minimum size 11.5 cm. Such a tool is compact, but inconvenient for a large amount of work. Optimally convenient and safe tool with a circle of 12.5 cm. Corner grinder for 15 cm disks is inconvenient for wood processing and create conditions for increased injuries.

When choosing a circle, it is necessary to focus on the labeling indicated on the disk. its diameter, thickness, size of the seat, the maximum allowable rotation speed, the shelf life of the circle and the material that can be treated with its help.

If a largest disk is installed on the corner grinder than the manufacturer is provided, then the speed of the cutting edge, breakdown of the circle and the infliction of injuries are possible. In addition, a small angular grinder may not have enough power to rotate a large disk. The most dangerous thing is that the installation of a large circle will require the dismantling of a protective casing, that with a cut of wood can lead to injury.

Grinding

The disk for grinding is selected depending on the nature of the work performed. Circles with rude abrasive, wire are suitable for pertair, draft work. The higher the quality of the grinding, the smaller the grains of abrasive material.

Circumpocks with the possibility of changing abrasive disks of various granularity attached to Velcro are convenient. The price of these interchangeable materials is low, but it is also low for operating time.

For finishing a wooden product. polishing circles from felt, pressed wool are used.

Detachment

It is advisable to approach the choice of a cutting disk more responsibly, since sawing work is characterized by increased injuries.

Do not process wood with disks designed for metal, stone or ceramics. To work with them requires higher strength, high speed. In a tree, such a circle can be bent, broken, and the tool will burn.

Modern models of the Bulgarians are equipped with a standard shaft with a diameter of 22.2 mm. old models have a shaft of other sizes. And if the disk can be installed on a model with a smaller shaft diameter using a special nozzle, then if the shaft is larger diameter, then the installation of the circle will be impossible.

Do not save on the quality of the disk. Corner grinder creates high speeds, so the discs are made from high.strength expensive material. tungsten carbide. Discs have increased strength and guarantee safety.

The cut.off discs differ in diameter, the cut depth, in shape, frequency of cloves and their number:

  • For sawing wood of different characteristics, the best option is a disk with a variable mowed cloves.
  • For soft rocks, use circles with straight teeth.
  • For wood-and-piece stove of medium density, laminated material, troops of wood-fiber slab, circles with trapezoidal teeth are used.

When cutting the material, severe heating of the discs is possible. When processing metal or stone, water cooling is used, when processing a tree, this is impossible. Therefore, in order to prevent overheating of the disk, its expansion and possible deformation, they produce discs with rounded slots, through or filled with copper.

Working and safety rules

Wood processing angular grinder requires a serious attitude and strict observance of the rules of operation of the device and personal safety:

  • It is strictly forbidden to remove the protective casing during operation. With a breakdown of the working disk, it will prevent the injury of face and body with fragments.
  • For wood work, preference should be given to medium.fitting models angular grinder. In the case of a failure of the process and jamming of the tool, it will be much easier to hold it in the hands, compared with a more powerful.
  • Grinding wheels are much safer in operation than cutting. When using them, it is advisable to use the mask to prevent wood dust and small sawdust enters the respiratory tract. It is also desirable to put on the goggles.
  • When working with cutting nozzles on an angular grinding grinder, it is necessary to strictly adhere to a right angle for wood processing, otherwise the cutting will occur unevenly and the angular grinder may jam.
  • You can not use disks in the work that are not suitable for at least one of the parameters for the angular grinder used.
  • It is strictly forbidden to use discs even with minimal signs of damage, especially when cutting wood.
  • It is forbidden to install instead of a disk on a corner grinder on wood circles from circular or other tools. Circular discs are designed for operation at low speeds and on an angular grinder can simply be baked or broke and fly apart.
  • Before grinding the tree with a corner grinder, it must be well dried. Wet wood is poorly grinded, moreover, there is a high probability of its lesion with mold and fungus.

How can you cut a tree with a corner grinder

We repeat once again: you can not cut a tree and any other material without a protective casing! When working, do not press on the corner grinder with great effort. Never make a direction rotation of the circle to yourself. only from yourself.

Do not saw the barrel if its thickness exceeds half the radius of the circle. Do not work if other people are near you, especially children. You can not touch the nozzles immediately after work, the metal that has hot from cutting and friction can lead to serious burns.

Small video material on our topic that will help to understand the basics of working with this tool:

Log in or register to write Комментарии и мнения владельцев, ask questions and participate in the discussion.

If you cut it, take a lot of bison with as a frequent tooth and inserts, enough for some time, then if you give it back, or rather and most likely just straighten the teeth, good sharpening is a very laborious lesson and there is money

From my experience I will say. Buy a corporate disk, Makita, Metabo, Bosch, you will not regret. Yes, it costs 2-3 tr, but it costs.Here is like that. Makita.Org.ru/osnastka/Diski/Diski-Pilnye/2429/

disk, stove, corner, grinders, wood-piece, chips

take a disk for that kind of money in order to lay 20-30 kV laminate? A normal person will buy a disc for 500. And in production, yes, it is better to take a good disk.

I also saw an attack before, and other China. And after I tried Makita, I realized that I was a loser, and was in vain to push the circular with two hands when you could with one finger 🙂

The more teeth, it’s cleaner than a cut!(with surfaces!).ure

Check out the Hearthstone Heritage wood stove heater !! #shorts

Not certainly in that way.With a large number of teeth, a very small distance between them. If large turns, then small chips do not have time to fly out in one revolution and begins to burn the material and disk. Wins quickly stupid and chips appear.That is, either smaller teeth, or lower speeds.

well, this is a generalized statement)) not literal.so that after 1 mm there are teeth!) such probably does not exist and turnover with adjustment on the circular ?) I did not.)

Look at the marking of the disks. 85mm diameter. Obviously not on the machine))

3 most unique homemade wood stoves YOU SHOULD KNOW

A person is clearly not interested in such, he is interested in the discs from the circular.)

That’s exactly what. Revolutions 6 thousand. This is a minipil

exactly) my fault.I did not see the inscriptions on the disks.))

The second disk, we use it in production, but basically use the laminated wood-and-steering plate, and the Finnish plywood

The first disk. for the dissolution of the boards. He has a scan of teeth, so that it would not be closed.For a pure cut of laminate and plywood, you need a disk with a winning and with alternately mowed sharpening.

I really do not recommend taking cheap China. Get a winning attack in the forehead)

I support the previous speaker. Laminate saw (preferably more expensive) and forward. Files with ordinary tooth on a laminate sitting.I always cut normally in length.

Lower for plywood. ATO cut will be like a type of upper laminate with a lobby with a small tooth

For direct cuts, it is not very conveniently especially longitudinal

Since 2001 in the decoration and always used a jigsaw and no problem.Well, yes, I agree that the length is better than the circular, but with a small tooth, so that the laminate does not tear much

It depends on the jigsaw itself. the consumer consumption for “500” will be wagged with a file. Here you have a curve “furry” cut.

I myself work with such a machine with such disks The one that the second saws everything at all.Both plywood and laminate and slate and asbo-cement plates And the one that is the first (he was also in the set) I don’t understand at all why (foil foil)

Of these. definitely the second. And if you choose, then not just with attacks, but with a negative angle and a trapezoidal tooth, as well as with the maximum number of teeth. These are specialized laminate disks. They saw slowly (due to the negative angle of teeth), but as clean as possible (as much as possible for disks).

You’re wrong. A negative angle is needed for sawing aluminum profile.

As the trapezoidal sharpening of teeth is written in combination with the negative angle of inclination is ideal for thin.walled metal and plastic profiles, for high.quality cutting of plates, panels and laminate “. So we are both right.

| Denial of responsibility | Contacts |RSS