What is a jack of a hammer photo

Jurk hammer. A rough construction tool that requires maximum caution and attentiveness. Enforcement is a frequent outcome during the operation of this device. But difficulties arise not only with the direct use of the chipper, but also at the stage of purchase. Let’s see the numerous types, areas of application and criteria for choosing this construction device, as well as consider the basic safety rules.

jack, hammer, jumping, construction, choice

Technical characteristics of the chipping hammer

The main technical characteristic of the jack of the chip is its strength of the strike and their number. The vastness of the tool depends on the power of power, in turn. For good chosen performance, its power indicators should vary within 2-70 J. There are models that are equipped with mechanisms with a high shock frequency, but with a slight force. The chipper works according to a fairly simple principle. The device’s drive activates the battleship located inside the case. Then he transfers mechanical impulses to the chisel itself. As a result, the system creates movement in the shock area. The speed in some cases can reach 1-2 thousand beats per minute. Such rapid effects and lead to the fleeting destruction of the processed surface.

The chipsters differ according to several criteria, including first of all it is worth noting the scope of application and power:

Electric jack hammers operate from a standard network of 220 V, so they can be used both in everyday life and in production. They are relatively quiet and quite easy to operate, which deserved wide popularity among users of various fields. It is these modifications that are most often purchased for home repairs or when it is necessary to buy a chipper for one-time construction and installation works. Network models are represented by a rich choice, they are made by almost all trademarks, and in different layouts. From very economical and light hammer to top heavy units.

Makita HM1203C

In terms of technical characteristics and impact energy, the makita chipper belongs to the average level of percussion instruments. The quality of manufacture and endurance of all mechanical nodes remain at the highest level, which makes this chipper the best choice for daily operation at high loads. Makita hammer is equipped with all the systems necessary for comfortable work. First of all, it is a constant electronics, holding the momentum at the same level, regardless of the load, and the function of the smooth start, which prevents jerking when turning on.

As follows from the reviews, the optimal scope of this model is the dismantling of brick structures, opening the asphalt coating and working with concrete of medium rigidity. The hammer copes easily with all these materials, the only thing that does not fit for is high.Strength concrete mixtures. In this case, its 1.5 kW of power will not be enough.

  • High performance;
  • The possibility of long.Term work;
  • Indicators of wear of brushes and cable integrity;
  • Long power cord. 5 m;
  • A worked out vibration damping system;
  • High strength shock mechanism.

Bosch GSH 501 Professional

Light Bosch electric hammer with the type of SDS-MAX mount is a typical representative of the brand’s professional line, with all the characteristic advantages. The tool is based on a powerful engine with an enlarged resource, which allows daily to perform heavy, laborious work on an industrial scale.

The chipper has a good impact force in 7.5 J, transmitted to the equipment through specially designed to increase performance, an elongated barrel. So that the electric jack of a hammer serves much longer, its case is made of shockproof plastic, which can withstand even falling from a height. And the tool itself is designed in such a way that all switches are protected from damage when contacting the surface. Reviews of the owners indicate that this model does not have objective shortcomings.

  • High quality of nodes and parts;
  • Durable case;
  • Power cord with fracture protection;
  • Reliability and practicality;
  • Light weight.

Stanley Sthm10k

The jack of a hammer with good power of the blow has established itself as a high.Performance tool that can cope with almost any materials. With it, you can expand the doorways, open the road surface, dismantle brick and concrete fences or walls. The quality of manufacture of the chipper and technical characteristics allow you to use it not only in everyday life, but also in professional conditions. The classic hammer design provides reliable grip and convenience during operation, both in vertical and horizontal position. However, there are negative responses with complaints about the large weight of the penetrator, which makes it possible to work on weight.

  • Large shock energy;
  • Smooth start;
  • The presence of an indicator of wear of the brushes;
  • Rubberized handle;
  • High power;
  • Ergonomic structure.

Hitachi H41MB

The H41MB chipped hammer model is equipped with an electric motor with a capacity of only 930 watts, which positively affected the weight of the tool. At the same time, in terms of impact power. 10 J, it significantly exceeds not only analogues, but also more powerful tools. Together with the highest quality of manufacture and an affordable price, it is safe to say that this chipper is the best in its class. The manufacturer and the specifics of this model took into account. Since light peorators are often used to work at altitude, its case is made of anti.Suggestion plastic. And the handle rubberized in the places of contact will not allow the tool to slip out of the hands. Users also note a good set of a popular chipper, which includes a strong, roomy case and equipment necessary for work. Of the negative moments, the absence of indicators of wear of brushes and the integrity of the power cable is called.

Sturm! RH2521P

The electrical hammer of the German brand Sturm is released by impressive shock capacity and high performance. Than two kW of the electric motor power is enough to issue 60 J, this is the best indicator in the class of heavy chips. Such technical data allow the use of the device for the most difficult work to destroy or dismantle any objects or structures even from durable, monolithic concrete.

To increase the resource, an electric hammer is equipped with an improved ventilation system and a more reliable gearbox compared to predecessors. And to facilitate the work of the operator, the manufacturer has provided a double system for extinguishing vibrations. Most of the reviews of the owners of this model are positive, mainly the tool is praised for the reliability of internal nodes and the highest power, but it was not without flaws. First of all, it is a fragile main pen, which often breaks due to shock loads, a short power cord and a large weight.

Types of jack hammers

The main idea of ​​the tool designed to destroy solid materials is the periodic movement of the working equipment, and the working stroke provides a shock load, and idle returns it to its original position. The easiest drive for such a scheme is to turn the rotation of the engine shaft into a re-surveying movement of the chisel using a curved-shaped mechanism.

Another approach to the drive of the chipping hammer is the use of compressed air or working fluid pressure. Using the system of bypass valves, the same impulse effect is achieved.

These two principles of the drive underlie the classification of chips.

Hydraulic

The work of such jack hammers is based on the fact that the working fluid under high pressure enters the system of spools and valves, where it is converted into the impulse movement of the bite. To do this, you need to connect two hoses. For the supply and return of the liquid. The transmission oil is used as a liquid, which is pumped to the desired pressure in the pump station.

In parallel with this, there are chipper in which a hydraulic motor is installed, which rotates the rotor due to oil pressure. With the help of a crooked-shaped mechanism, the movement of the piston transmitted to the boiler is ensured.

The scope of hydraulic jack hammers is limited to the specifics of operation. For example, they are indispensable when working under water, where an electric tool is dangerous, and pneumatic creates interference with exhaust air.

Gasoline

These chipsters as a drive have an internal combustion engine and through a crooked-shaped mechanism with a piston transmit an impulse to a boiler. To increase the power of the hammer, it is necessary to increase the engine volume and install a larger fuel tank.

That is why the gasoline chipper has a larger size and weight. In addition, flammable fuel is a danger. They cannot be used in limited space due to the danger of poisoning with exhaust gases.

These disadvantages limit the scope of such a tool. They are used where there is no electricity at all: they are used in emergency situations in the analysis of the rubble of the hit buildings, when it is impossible to supply electricity or compressed air.

Pneumatic

These hammers function in the same way as hydraulic, only instead of oil is a stream of compressed air. They are very compact, reliable and safe. They were widespread in construction work and in mines, when mining and dismantling building structures.

They need an air compressor. The only drawback is a high noise level when air exits the body.

Electric

As a drive, an electric motor is used. They have a lot of advantages. Light and compact they began to be widely used in everyday life. Electric tool manufacturers offer a variety of models that differ in both power and impact power.

In parallel with the chipper, a peorator appeared. A device that combines the impulse effect and drill. Such a tool is indispensable if necessary to make holes in concrete and brick walls.

The disadvantages of electrical jack hammers include the risk of sparks on the electric motor collector. This limits their use in conditions of increased fire hazard, especially when the gas pipes are released from the walls. Therefore, they are not used in mines, as well as in rescue work on the ruins of houses and industrial buildings.

Jackhammer in rust

Jacking hammer in the rast is the most preferred tool for many players for the extraction of stones, metals and sulfur ore. This instrument gained its popularity for high production speed, good strength and the possibility of free repair, but more on that later.

It is much easier to extract resources using a chipping hammer, even in comparison with an ice ax. Only a few seconds will go to the farm of one stone. Immediately I’m talking about a bonus. The jaws do not perceive these “vulnerable points”, it makes no sense to beat.

Unlike the chainsaw, Jackhammer does not require any fuel. Just follow the margin of its strength. The strength dropped to a minimum or the chipper has already broken. Get to any workbench (workbench used in crafting), open the inventory, and through it already restore the jackhammer. This procedure is absolutely free.

If you still do not know how to break the tank into a plant, we will inform you that the jack of a hammer is the best choice, since it mines the maximum resources for a minimum of time. I also advise you to get acquainted with the article Rust Tank, in which they talked about how to destroy the tank of the plant, the hp tank of the plant.

Jackhammer

A variety of jack hammers by type of drive

To ensure the functioning of the chipper, it is necessary to equip it with a drive, which will rotate the connecting rod mechanism:

Electric are the most popular and common due to many advantages. They surpass all other varieties in efficiency, as well as cheapness of service. These chips with relatively small weight have a rather large destructive ability. They create a low level of vibration on the handle, which is especially important if the work is carried out for hours. The only drawback of electrical chipsters is the impossibility of working in conditions of high humidity. Too humid air leaves condensate on a working electric motor, which can lead to a short circuit. It should also be noted the attachment of this tool to the outlet. If there is a generator, this drawback can be completely circumvented by connecting the chipper to the station.

Gasoline are autonomous. They are equipped with an internal combustion engine, which works as a result of burning gasoline. Diesel devices are not produced due to the fact that such motors are much harder, so it is difficult to endure. Gasoline hammers are used in the field, when road work is carried out, the dismantling of the sleepers on the railway, as well as for drilling in a solid rock for installing supports. These chips are quite heavy, and besides this they work very noisy. In addition to the very blow of the peak on the destroyed material to the sound of a working tool, the engine noise is added. It will not be possible to work with gasoline devices indoors. The engine forms exhaust gases. The cost of using such a chipper is the highest, since the price of gasoline is much higher than for electricity.

A pneumatic jack of a hammer is used in conditions when the release of exhaust gases is unacceptable, as well as the use of electric wires. It is such equipment that is installed in mines. A high.Pressure pneumatic hose, coming from a compressor operating on the surface or nearby, is connected to the device. The advantages of this equipment include the possibility of use in conditions with high humidity, as well as the absence of sparkling flashes inside the case, which certainly arise when the electric motor is operating.

Varieties of hammers depending on the shape of the case

Depending on the shape of the case, the chips are divided into horizontal and vertical. Horizontal are the lightest. They are designed to process horizontal planes. It is these tools that are used in the repair work. With their help, you can destroy the walls in the room, as well as perform other varieties of work. Outwardly horizontal chips resemble a conventional drill or peorator. They are quite light, but differ relatively low performance.

jack, hammer, jumping, construction, choice

Vertical chips are the most difficult. They are designed for vertical installation and destruction of the surface on which the operator stands. Such equipment is used by road builders to remove asphalt and t.P. The weight of such a tool can often reach 30 kg and even higher. The created impact force is very large. The height of such chipsters is designed in such a way as to reach the operator’s waist.

Criteria for choosing a chipper

When choosing a junk hammer, you should navigate not only by type of drive and constructive features, but also by other criteria:

Power

The capacity of the jack of junk ranges from 500 to 2000 watts. Too weak models up to 1200 watts are hardly better than an ordinary peorator, since they are characterized by low performance and weakness of the blow. To fully engage in finishing work when repairing premises, you need a hammer with a capacity of 1200-1600 watts. He will be able to destroy concrete, brick and stone. Powerful rather heavy, and are usually used by road builders, since they are able to ruin elastic asphalt and t.P.

The mass of the tool

The more powerful the jack of the hammer, the harder it is. To work with such a tool, it is necessary to have physical strength and endurance. A hammer must be chosen depending on physiology. By weight, chipping hammers can be divided into three categories:

Light have weight up to 6 kg. They are used for work at altitude. They are usually used by industrial climbers for clearing interpanel sutures. Although this equipment is not highly effective in destruction, it is not always possible to take a more difficult tool.

Medium in weight of hammers have a weight of 5 to 10 kg. Typically, this category is represented by horizontal chipsters, which are used in the demolition of walls, as well as for cutting holes and openings.

Heavy hammers have a mass of 10 to 30 kg. They are used by miners, as well as road builders. These are vertical models that can break through even a massive reinforced concrete foundation.

Impact strength

The impact force is a very important indicator of the effectiveness of the chipper. The higher it is, the more material he will break when the pika hit. This indicator is measured in joules. Jumping hammers presented on the market usually have a hit of 2.8 to 60 J. Light chipper can give up to 15 J, medium to 35 J, and heavy up to 60 J

Jackhammer. Types and device. Work and application. Choose

The junk hammer is a shock-mechanical manual tool, which is designed to loosen and split solid materials, such as rock, asphalt, concrete, stone and brick. It is quite difficult and is used to perform complex tasks. The working part of the hammer is the peak, which carries out the splitting.

Inside the device is a drive usually in the form of an engine that rotates the connecting rod. The connecting rod is connected to the piston, which tightly adjacent to the inner walls of the metal tube. On one side of the tube, a piston is installed, which is attached to the connecting rod, and from the second it is drowned out by the moving cylinder. While moving the piston forward, air is compressed in the tube chamber. He pushes the cylinder. The frequency of movement of the cylinder fully corresponds to the mobility of the piston. At the end point of removal from the piston, the cylinder strikes the chipper. As a result of the impact, an impulse is created, which is transmitted to the peak. The peak itself remains motionless. The impulse passes through it and hits the surface, which must be destroyed. After the impact, the piston returns with a connecting rod to its original position, while the air is also drawn behind the cylinder. Further, the movement is repeated again. The frequency of the blow has a jack of a hammer is usually about 30 in a second.

The impulse transmitted to the peak can be compared with the blow of a usually hand hammer on a substitute chisel. Due to the high frequency of pulses, which the jam of the jaws itself creates, a fairly quick splitting of materials is carried out. There is practically no pressure at the peak, so its acuity persists longer than if it was used as a cutter.

The use of the cylinder and the air gap between it and the piston is constructive in this system. If the piston will directly beat at the peak or drummer, then the resulting returns will directly affect the drive that rotates. As a result, the tool will become unusable in just a few strokes. The air gap works as a shock absorber, blocking the return.

Electric are the most popular and common due to many advantages. They surpass all other varieties in efficiency, as well as cheapness of service. These chips with relatively small weight have a rather large destructive ability. They create a low level of vibration on the handle, which is especially important if the work is carried out for hours. The only drawback of electrical chipsters is the impossibility of working in conditions of high humidity. Too humid air leaves condensate on a working electric motor, which can lead to a short circuit. It should also be noted the attachment of this tool to the outlet. If there is a generator. This drawback can be completely circumvented by connecting the chipper to the station.

Gasoline are autonomous. They are equipped with an internal combustion engine, which works as a result of burning gasoline. Diesel devices are not produced due to the fact that such motors are much harder, so it is difficult to endure. Gasoline hammers are used in the field, when road work is carried out, the dismantling of the sleepers on the railway, as well as for drilling in a solid rock for installing supports. These chips are quite heavy, and besides this they work very noisy. In addition to the very blow of the peak on the destroyed material to the sound of a working tool, the engine noise is added. It will not be possible to work with gasoline devices indoors. The engine forms exhaust gases. The cost of using such a chipper is the highest, since the price of gasoline is much higher than for electricity.

A pneumatic jack of a hammer is used in conditions when the release of exhaust gases is unacceptable, as well as the use of electric wires. It is such equipment that is installed in mines. A high.Pressure pneumatic hose that comes from the compressor is connected to the device. Working on the surface or nearby. The advantages of this equipment include the possibility of use in conditions with high humidity, as well as the absence of sparkling flashes inside the case, which certainly arise when the electric motor is operating.

Varieties of hammers depending on the shape of the case

Depending on the shape of the case, the chips are divided into horizontal and vertical. Horizontal are the lightest. They are designed to process horizontal planes. It is these tools that are used in the repair work. With their help, you can destroy the walls in the room, as well as perform other varieties of work. Outwardly horizontal chips resemble a conventional drill or peorator. They are quite light, but differ relatively low performance.

Vertical chips are the most difficult. They are designed for vertical installation and destruction of the surface on which the operator stands. Such equipment is used by road builders to remove asphalt and t.P. The weight of such a tool can often reach 30 kg and even higher. The created impact force is very large. The height of such chipsters is designed in such a way as to reach the operator’s waist.

The capacity of the jack of junk ranges from 500 to 2000 watts. Too weak models up to 1200 watts are hardly better than an ordinary peorator, since they are characterized by low performance and weakness of the blow. To fully engage in finishing work when repairing premises, you need a hammer with a capacity of 1200-1600 watts. He will be able to destroy concrete, brick and stone. Powerful rather heavy, and are usually used by road builders, since they are able to ruin elastic asphalt and t.P.

Light have weight up to 6 kg. They are used for work at altitude. They are usually used by industrial climbers for clearing interpanel sutures. Although this equipment is not highly effective in destruction, it is not always possible to take a more difficult tool.

Medium in weight of hammers have a weight of 5 to 10 kg. Typically, this category is represented by horizontal chipsters, which are used in the demolition of walls, as well as for cutting holes and openings.

Heavy hammers have a mass of 10 to 30 kg. They are used by miners, as well as road builders. These are vertical models that can break through even a massive reinforced concrete foundation.

Jackhammer. Types and device. Work and application. Choose

The junk hammer is a shock-mechanical manual tool, which is designed to loosen and split solid materials, such as rock, asphalt, concrete, stone and brick. It is quite difficult and is used to perform complex tasks. The working part of the hammer is the peak, which carries out the splitting.

jack, hammer, jumping, construction, choice

Inside the device is a drive usually in the form of an engine that rotates the connecting rod. The connecting rod is connected to the piston, which tightly adjacent to the inner walls of the metal tube. On one side of the tube, a piston is installed, which is attached to the connecting rod, and from the second it is drowned out by the moving cylinder. While moving the piston forward, air is compressed in the tube chamber. He pushes the cylinder. The frequency of movement of the cylinder fully corresponds to the mobility of the piston. At the end point of removal from the piston, the cylinder strikes the chipper. As a result of the impact, an impulse is created, which is transmitted to the peak. The peak itself remains motionless. The impulse passes through it and hits the surface, which must be destroyed. After the impact, the piston returns with a connecting rod to its original position, while the air is also drawn behind the cylinder. Further, the movement is repeated again. The frequency of the blow has a jack of a hammer is usually about 30 in a second.

The impulse transmitted to the peak can be compared with the blow of a usually hand hammer on a substitute chisel. Due to the high frequency of pulses, which the jam of the jaws itself creates, a fairly quick splitting of materials is carried out. There is practically no pressure at the peak, so its acuity persists longer than if it was used as a cutter.

The use of the cylinder and the air gap between it and the piston is constructive in this system. If the piston will directly beat at the peak or drummer, then the resulting returns will directly affect the drive that rotates. As a result, the tool will become unusable in just a few strokes. The air gap works as a shock absorber, blocking the return.

Electric are the most popular and common due to many advantages. They surpass all other varieties in efficiency, as well as cheapness of service. These chips with relatively small weight have a rather large destructive ability. They create a low level of vibration on the handle, which is especially important if the work is carried out for hours. The only drawback of electrical chipsters is the impossibility of working in conditions of high humidity. Too humid air leaves condensate on a working electric motor, which can lead to a short circuit. It should also be noted the attachment of this tool to the outlet. If there is a generator. This drawback can be completely circumvented by connecting the chipper to the station.

Gasoline are autonomous. They are equipped with an internal combustion engine, which works as a result of burning gasoline. Diesel devices are not produced due to the fact that such motors are much harder, so it is difficult to endure. Gasoline hammers are used in the field, when road work is carried out, the dismantling of the sleepers on the railway, as well as for drilling in a solid rock for installing supports. These chips are quite heavy, and besides this they work very noisy. In addition to the very blow of the peak on the destroyed material to the sound of a working tool, the engine noise is added. It will not be possible to work with gasoline devices indoors. The engine forms exhaust gases. The cost of using such a chipper is the highest, since the price of gasoline is much higher than for electricity.

A pneumatic jack of a hammer is used in conditions when the release of exhaust gases is unacceptable, as well as the use of electric wires. It is such equipment that is installed in mines. A high.Pressure pneumatic hose that comes from the compressor is connected to the device. Working on the surface or nearby. The advantages of this equipment include the possibility of use in conditions with high humidity, as well as the absence of sparkling flashes inside the case, which certainly arise when the electric motor is operating.

Varieties of hammers depending on the shape of the case

Depending on the shape of the case, the chips are divided into horizontal and vertical. Horizontal are the lightest. They are designed to process horizontal planes. It is these tools that are used in the repair work. With their help, you can destroy the walls in the room, as well as perform other varieties of work. Outwardly horizontal chips resemble a conventional drill or peorator. They are quite light, but differ relatively low performance.

Vertical chips are the most difficult. They are designed for vertical installation and destruction of the surface on which the operator stands. Such equipment is used by road builders to remove asphalt and t.P. The weight of such a tool can often reach 30 kg and even higher. The created impact force is very large. The height of such chipsters is designed in such a way as to reach the operator’s waist.

The capacity of the jack of junk ranges from 500 to 2000 watts. Too weak models up to 1200 watts are hardly better than an ordinary peorator, since they are characterized by low performance and weakness of the blow. To fully engage in finishing work when repairing premises, you need a hammer with a capacity of 1200-1600 watts. He will be able to destroy concrete, brick and stone. Powerful rather heavy, and are usually used by road builders, since they are able to ruin elastic asphalt and t.P.

Light have weight up to 6 kg. They are used for work at altitude. They are usually used by industrial climbers for clearing interpanel sutures. Although this equipment is not highly effective in destruction, it is not always possible to take a more difficult tool.

Medium in weight of hammers have a weight of 5 to 10 kg. Typically, this category is represented by horizontal chipsters, which are used in the demolition of walls, as well as for cutting holes and openings.

Heavy hammers have a mass of 10 to 30 kg. They are used by miners, as well as road builders. These are vertical models that can break through even a massive reinforced concrete foundation.

How to work with a jack of a hammer

Jacking hammer is a tool that works in shock mode in the most difficult operating conditions. That is why the working properties of this tool determine the specifics of working with it.

#Source_Engine Полезные программы. Hammer

Before starting work with shock equipment, you should adhere to a simple rule. Keep the workplace clean and dry. Extraneous objects, including unnecessary equipment, should be removed. If you hammer the walls or drill deep holes in them, then you should first check them with a hidden wiring detector so that you suddenly do not hit the current. Further, when working in places with a large cluster of people, enclose the working area from the entrance of unauthorized persons so that they do not be close to a working tool. One of the most important rules that should be observed is reading the instructions for the tool, it indicates the basic characteristics of the jackhammer and the rules for working with it. This will protect the tool from breakdowns when improper operation, and you. From injuries.

Take care of the equipment. The operator’s clothes should be dense and close the body as much as possible to protect it from sparks, fragments of concrete or brick. Also, we should not forget about soundproofing headphones, gloves and glasses. If the working area is very dusty, then the respiratory system will protect the respirator well.

Preparation of a jack of a hammer for work

The tool itself, like the workplace, requires careful preparation. First, inspect it for external damage, whether all nodes and equipment are reliably tightened. Particular attention should be paid to an electric wire so that he does not have strong bends or breaks. Ideally, the voltage of the mains must be checked by a multimeter to make sure that it corresponds to the voltage for which the hammer is designed. With unstable voltage, use a stabilizer, it will avoid a tool breakdown during jumps in the mains. Following the rules for preparing a hammer for work allows not only to be dismantled with its help, but also to prevent premature breakdown of the unit. It should be borne in mind that if you work with a pneumatic tool, then the compressor should have higher power and pressure pressure than the characteristics of the chipping hammer. Thanks to this, you exclude interruptions in the operation of equipment due to power loss.

As for equipment, always make sure that the equipment cartridge is clean. The chisel is selected by the type of shank and the size of the hole in the hammer.

First of all, the chipping hammer requires regular lubrication, while the new equipment is generally lubricated several times per shift. With constant use, the amount of lubricant decreases to a couple times per working day.

Next, note that the handle and the shock mechanism must move freely, t.You will have to work continuously for a long time.

If you work with an electric tool, then, accordingly, it cannot be used with high humidity or in the open air. He can shorten, hit you with an electric shock and break.

If you remove the old asphalt coating or getting freezing the ground, then work only with a hammer that has high power rates. And vice versa, you should not remove the tile in the bathroom for mining to mining minerals without adjusting the revolutions. Lose both the jackpot and walls in the bathroom.

Do not make a lot of effort during work, otherwise the equipment with the motor will suffer. By the way, immediately after using the unit, let the equipment cool down so as not to get a burn. T.The state of accessories to equipment directly affects the efficiency of the chipping hammer, make sure that they are always well sharpened (for example, flat chisels) and are stored in a dry place processed with a special composition against rust. The equipment should also be lubricated before operation, in particular, this applies to cases when you hammer the hole with a drill.

While working with an electric hammer, follow the electric wire so that it does not fall under the cutting part or does not spin around your foot. Also look so that he is not damaged by the fragments, and do not pull for it to pull out the fork.

How to use the chipper?

Before starting work, the device should be checked for performance and lack of hidden defects that can lead to emergency situations. It should be remembered about the basic principles of security, namely:

  • Do not make maximum efforts when compressing the hands on the handle;
  • Comply with recommendations on the value of the working pressure;
  • Use special protective equipment (gloves, helmets, glasses, etc.D.);
  • Observe the correct position of the peak to, during and at the end of the work;
  • Keep a safe distance from the apparatus.

НЕВОЗМОЖНО СДЕРЖАТЬ ЭМОЦИИ! СИЛЬНЕЙШАЯ ВОЕННАЯ ДРАМА! Отчий Берег / ANCESTRAL LAND (English Sub)

Useful tips and instructions when working with a jack of a hammer

The first thing you should pay attention to is the lubrication of individual elements of the hammer. Professional builders prefer to lubricate the tool several times per shift. At the end of the work, the tool should “cool down”, t.To. In the process, its elements are subject to increased heating. Also, during operation, attention should be paid to the state of the wire: construction practice is known when it fell under the cutting part of the tool, and also twisted around the operator’s legs, which led to rather decayed consequences.

| Denial of responsibility | Contacts |RSS